Stihl 1121 · Section A · 1 of 16 · 45 parts
Crankcase
Fits 024.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (45)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1121 020 2117 | Crankcase | 1 |
| 1 | 1121 020 2112 | Crankcase → replaced by 1121 020 2117 TI 43/2001 | 1 |
| 2 | 9371 470 2610 | Cylindrical pin 5x18 | 2 |
| 3 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 4 | 1128 640 9100 | Valve | 1 |
| 5 | 0000 988 5211 | Connector | 1 |
| 6 | 9416 868 6531 | Hollow rivet 6.5x0.5x6.8 | 2 |
| 7 | 1120 162 5200 | Pin | 1 |
| 8 | 1121 162 5205 | Pin | 1 |
| 9 | 1121 162 5200 | Pin | 2 |
| 10 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 5 |
| 11 | 9523 003 4260 | Grooved ball bearing 15x35x13 | 1 |
| 12 | 9503 003 0320 | Grooved ball bearing 16002 | 1 |
| 13 | 9640 003 1600 | Oil seal 15x29.6x4 | 1 |
| 14 | 9640 003 1190 | Oil seal 12x20x5 | 1 |
| 15 | 1122 647 9400 | Hose | 1 |
| 16 | 1117 640 3800 | Pickup body | 1 |
| 17 | 1121 029 0500 | Gasket | 1 |
| 18 | 1121 030 0400 | Crankshaft | 1 |
| 19 | 1121 030 0405 | Crankshaft | 1 |
| 20 | 1120 036 8500 | Woodruff key 2x3.7 | 1 |
| 21 | 1121 640 1905 | Tensioner slide | 1 |
| 22 | 1121 664 1600 | Adjusting screw | 1 |
| 23 | 1125 664 1400 | Thrust pad | 1 |
| 24 | 1122 664 2200 | Cover plate | 1 |
| 25 | 9041 216 0630 | Pan head screw M4x8 Fitment / change note → | 2 |
| 26 | not sold separately | Spur gear not available as a separate item | 1 |
| 27 | not sold separately | Adjusting screw not available as a separate item | 1 |
| 28 | 9646 945 0490 | O-ring 7x1.5 | 1 |
| 29 | 1125 640 1900 | Tensioner slide | 1 |
| 30 | 1122 664 1000 | Inner side plate 0.5 mm Fitment / change note → | 1 |
| 31 | 1122 664 1001 NLA | Inner side plate Fitment / change note → option | 1 |
| 32 | 1120 664 1500 | Tensioning nut | 1 |
| 33 | 1121 664 2800 | Guide piece | 1 |
| 34 | 9043 319 8100 | Pan head screw M5x50 | 1 |
| 35 | 1121 648 6610 | Bumper strip | 2 |
| 36 | 1124 084 8301 | Reflector foil option | 1 |
| 37 | 0000 350 0526 | Filler cap | 1 |
| 38 | 9645 948 2470 | O-ring 23x3 | 1 |
| 39 | 0000 350 0510 | Filler cap | 1 |
| 40 | 0000 359 1210 | Sealing ring | 1 |
| 41 | 0000 350 0900 | Rope | 1 |
| 42 | 0000 353 0600 | Hook | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1121 007 1021 | Chain tensioner kit | 1 |
| — | 1121 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 024 / 026 / 034 / 036
024 / 026 / 034 / 036: sprung side plate requires the revised cover
Side plate 1122 664 1000 changes to 1122 664 1001; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.
- When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
- Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
- The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
- The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
- For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
- Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
- Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
- Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.
Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.
Part numbers (7)
- 1122 664 1000 — Original side platePrevious version · Retained for original cover
- 1122 664 1001 — Sprung-tab side plateNew version · Requires new-version cover
- 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
- 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
- 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
- 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
- 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
Wrong number or missing part for the 024? Report a correction →