← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section C · 3 of 17 · 23 parts

Oil pump

Fits 026.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415151617181922021212233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 1121 640 3203 Oil pump adjustable 1
2 not sold separately Clutch drum not available as a separate item 1
3 0000 958 0408 Washer 2
4 0000 997 2002 Compression spring 1
5 1121 647 0603 Pump piston 1
6 1121 641 9400 Bearing bushing 1
7 9646 945 0160 O-ring 4x2 2
8 1128 647 4806 Control bolt 1
9 9380 620 1090 Roll pin 2x10 1
10 0000 958 1234 Washer 1
11 1121 640 7111 Worm 1
12 1121 647 3100 Carrier 1
13 0000 993 0508 Ring 12x15x12 1
14 9022 313 0660 Spline screw IS-M4x12 2
15 0000 958 0407 Washer 2
16 0000 997 0504 Compression spring 1
17 1121 647 0601 Pump piston 1
18 1121 647 7002 NLA Plug 1
19 1121 640 7110 Worm 1
20 1121 640 3202 Oil pump 65 (0.65 mm stroke) Fitment / change note → 1
21 1121 640 9400 Hose 75 mm / 3'' 1
22 1121 036 1600 Worm 1
Not numbered on the diagram — assemblies, kits and options
— 1121 007 1043 Conversion kit oil pump, adjustable option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 026

026: check oil-pump piston lubrication

Before fitting a new oil pump and when servicing 026, check the pump-piston lubrication and replenish it if necessary.

  • The source sequence is: pry the plastic plug out of the pump body; apply a little grease to the piston control face; refit the plug. Replenishment is conditional on the lubrication check, not a stated periodic grease interval.
  • TI31/1995 gives no pump, piston or plug part number, grease specification, measured quantity or changeover serial in this section. The catalog sheet supplies context only: no catalog number is promoted into this source note, and no adjustable/non-adjustable interchange is claimed.
  • This section says 026, not 024. These are historical source instructions, not an executed hardware procedure.

Source: TI 31/1995, p. 6 — Section 2: complete numberless oil-pump service note.

No additional parts-table entry added.

Conditional replacement · 026

026: off-white oil pump 65 is for non-adjustable systems only

Pump 1121 640 3202 replaces die-cast 1121 640 3210 only on 026 with a non-adjustable pump; its 0.65 mm stroke and delivery remain unchanged.

  • Section 1 right column explicitly applies only to 026 with non-adjustable oil pump. Figure 133TI041 KN and summary items 3–4 change magnesium die-cast 1121 640 3210 to off-white-plastic 1121 640 3202. Both are oil pump 65 with 0.65 mm stroke; the TI states delivery rate remains unchanged, without providing a flow-volume measurement.
  • Prose says replacement in the foreseeable future; the page 2 summary says introduction on 026 is in progress. Neither supplies a serial or exact calendar cutoff. The previous pump remains factory-supplied only while existing stocks last under remark 1.
  • The exact 026 oil-pump IPL also includes adjustable 1121 640 3203 and conversion-kit rows. Their presence does not override the non-adjustable restriction or make the 024 black 3201 pump an 026 replacement. No adjustable conversion or cross-model pump interchange is admitted.
  • TI12/1999 historical guidance for the explicitly named 024/026 configurations only. No MS successor or general part-number-prefix compatibility is inferred. Factory supply statements are historical, not current availability. No physical interchange, oil-delivery measurement or brake test was performed.

Source: TI 12/1999, p. 1 · TI 12/1999, p. 2 · TI 12/1999, p. 3 — All three original USA pages: contents, sections1–4, four figures, all summaries, remarks and serial conditions.

Part numbers (2)
  • 1121 640 3210 — Previous oil pump 65; magnesium die-cast bodyOld non-adjustable pump; stocks-only supply · 026 with non-adjustable oil pump only; TI12/1999 section-specific conditions apply
  • 1121 640 3202 — New oil pump 65; off-white plastic, 0.65 mm strokeSame stated delivery; non-adjustable systems only · 026 with non-adjustable oil pump only; TI12/1999 section-specific conditions apply

Wrong number or missing part for the 026? Report a correction →