← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section B · 2 of 17 · 29 parts

Cylinder, Muffler

Fits 026.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171717171819220212223242526273456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (29)

PosPart numberDescriptionQty
1 1118 029 2306 Cylinder gasket 0.5 mm 1
2 1121 029 2305 Cylinder gasket 1 mm 1
3 9512 003 2250 Needle cage 10x13x12.5 1
4 1121 020 1203 Cylinder with piston Ø 44 mm Fitment / change note → 1
5 1121 030 2001 Piston Ø 44 mm 1
6 1121 034 3010 Piston ring Ø 44x1.2 mm 2
7 1121 034 1505 Piston pin 10x6x30 1
8 9463 650 1000 Snap ring 10 2
9 0000 953 0818 Stud M5 2
10 1128 020 9400 Decompression valve Fitment / change note → 1
11 1122 084 1405 Cover Fitment / change note → 1
12 1121 084 7100 Cap 1
13 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
14 1118 149 0600 Muffler gasket 1
15 1121 140 0604 Muffler 1
16 1121 145 0802 Exhaust casing 1
17 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 4
18 1121 140 0606 Muffler 1
19 1121 140 0802 Exhaust casing 1
20 1118 141 9005 Screen 1
21 9099 021 0810 Self-tapping screw 4.2x9.5 1
22 1110 400 7005 Spark plug Bosch WSR 6 F 1
22 0000 400 7000 Spark plug NGK BPMR7A 1
23 1121 140 0605 Muffler 1
24 1121 145 0805 Exhaust casing 1
25 9022 341 0980 Spline screw IS-M5x16 2
26 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
27 1122 025 2200 Plug Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 1121 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 026

026: decompression cylinder and shroud need closures when unused

Only the new cylinder and shroud were supplied; non-decompression use requires the cylinder plug and shroud cap, not an open hole.

X 32 252 039 — 026 production introduction of the new filter system and decompression valve; not the earlier complete-system retrofit threshold.

  • The valve is opened manually and closes automatically when the engine starts firing. The raised shroud opening protects against accidental contact, and cover 1122 084 1405 between cylinder and shroud reduces dirt ingress. Starting comfort is a source claim, not a bench result.
  • Only new cylinder with piston 1121 020 1209 and shroud 1121 080 1609 remain available in the 1995 bulletin. For use without decompression, seal the tapped cylinder hole with plug 1122 025 2200 and the shroud opening with cap 1122 084 7100. The plug is included with the cylinder (item 20 includes 21); the cap with the shroud (24 includes 25). All other parts remain as before.
  • Use a standard deep-well 13-mm socket for the decompression valve; source torque is 14 Nm (10.3 lbf.ft), for the valve only. For the engine pressure test, the TI recommends removing the valve and sealing its hole with plug 1122 025 2200.
  • IMPORTANT: remove the decompression valve before fitting the piston-locking strip during repair. No pressure-test value, cylinder-fastener torque or complete test procedure is supplied here.
  • The section is explicitly 026; the shared bulletin header does not establish this cylinder on 024 or successor MS260. These are source instructions, not a performed hardware procedure.

Source: TI 31/1995, p. 1 · TI 31/1995, p. 2 · TI 31/1995, p. 3 · TI 31/1995, p. 4 · TI 31/1995, p. 5 — Sections 1, 1.2–1.5: valve operation, closures, service and rows 20–25.

Part numbers (8)
  • 1121 020 1208 — Cylinder with pistonOriginal · 026; valve/closure configuration conditions above
  • 1121 020 1209 — Cylinder with pistonNew; includes plug · 026; valve/closure configuration conditions above
  • 1122 025 2200 — Cylinder plugRequired closure when valve absent · 026; valve/closure configuration conditions above
  • 1128 020 9400 — Decompression valveNew · 026; valve/closure configuration conditions above
  • 1122 084 1405 — Cover between cylinder and shroudNew · 026; valve/closure configuration conditions above
  • 1121 080 1608 — ShroudOriginal · 026; valve/closure configuration conditions above
  • 1121 080 1609 — ShroudNew; includes cap · 026; valve/closure configuration conditions above
  • 1122 084 7100 — Shroud capRequired closure when valve absent · 026; valve/closure configuration conditions above

Conditional replacement · 026 / MS 260

026 / MS 260: ignition-lead routing, harness and 44 mm cylinder

Routing changes involve the crankcase, shroud and cylinder; the second illustrated harness is not assigned a variant.

  • The ignition lead is carried in an insulating tube within the crankcase cable channel. A retainer near the annular-buffer mounting holds it in position. The shroud wall between carburetor box and cylinder has a molded guide; three cylinder fins were shortened to accommodate it. This describes the revised manufactured geometry, not an instruction to grind an old cylinder.
  • Short-circuit and ground wires are enclosed in shrink tube and routed as a harness to the carburetor box in an insulating tube. The yellow/green ground wire is secured by the lower ignition-module mounting screw.
  • The summary defines harness 1121 440 3002 as including cable lug 0751 030 8969 (A5-1.5, unchanged), contact sleeve 1110 442 7000 replacing 1119 442 7000, terminal socket 0751 030 8957 (4.8-1/0.8, unchanged), and insulating tube. The previous contact sleeve and 90 mm tube 1121 405 8001 remain available for older machines, but the new tube is not supplied separately and has no independent part number in this table.
  • The diagram additionally labels harness 1121 440 3003, but the TI does not assign its model/variant or list it in the summary. It is retained as an unassigned illustrated reference, not approved as a substitute for 1121 440 3002 or attributed to a heated variant.
  • For the explicitly named 026 and MS 260, the 44 mm cylinder with piston changes from 1121 020 1209 to 1121 020 1203. The previous version is supplied only while factory stocks last. The coordinated routing geometry does not establish universal component interchange.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 2 · TI 43/2001, p. 4 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Section7 routing and both harness drawings; summary rows28–32,38/remarks1–3.

Part numbers (9)
  • 1121 440 3002 — Wiring harnessSummary assembly including items29–32 · Only the named model/configuration; see conditions
  • 1121 440 3003 — Illustrated wiring harnessUnassigned diagram reference; no variant fitment established · No model/variant assigned by TI43
  • 0751 030 8969 — Cable lug A5-1.5Unchanged · Only the named model/configuration; see conditions
  • 1119 442 7000 — Contact sleevePrevious; retained · Only the named model/configuration; see conditions
  • 1110 442 7000 — Contact sleeveNew · Only the named model/configuration; see conditions
  • 0751 030 8957 — Terminal socket 4.8-1/0.8Unchanged · Only the named model/configuration; see conditions
  • 1121 405 8001 — Insulating tube 90 mmPrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 1209 — 44 mm cylinder with pistonPrevious; stocks only · Only the named model/configuration; see conditions
  • 1121 020 1203 — 44 mm cylinder with pistonNew · Only the named model/configuration; see conditions

Wrong number or missing part for the 026? Report a correction →