Stihl 1122 · Section C · 3 of 17 · 22 parts
Muffler
Fits 066.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (22)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 140 0602 | Muffler → replaced by 1122 140 0604 TI 27/2003 | 1 |
| 2 | 1122 145 0801 NLA | Exhaust casing | 1 |
| 3 | 1122 140 0603 | Muffler → replaced by 1122 140 0609 TI 19/1995 | 1 |
| 4 | 1122 141 9001 NLA | Screen | 1 |
| 5 | 1122 140 0800 | Exhaust casing | 1 |
| 6 | 1118 141 9005 | Screen | 1 |
| 7 | 9099 021 0810 | Self-tapping screw 4.2x9.5 | 1 |
| 8 | 1122 140 0613 | Muffler Fitment / change note → | 1 |
| 9 | 1122 145 0807 | Exhaust casing | 1 |
| 10 | 1122 149 0500 | Gasket Fitment / change note → | 1 |
| 11 | 1122 140 0614 | Muffler | 1 |
| 12 | 1122 145 0811 | Exhaust casing | 1 |
| 13 | 1125 149 0601 | Muffler gasket | 1 |
| 14 | 9022 341 0980 | Spline screw IS-M5x16 | 2 |
| 15 | 9022 341 1300 | Spline screw IS-M6x20 | 2 |
| 16 | 9022 341 0910 | Spline screw IS-M5x6 | 2 |
| 17 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 17 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 18 | 0000 148 6000 | Tensioning gear | 2 |
| 19 | 1122 140 0609 | Muffler Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 007 1053 | Set of gaskets | 1 |
| — | 1122 007 1054 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 066
066: smaller-outlet muffler is EPA-only; renew the casing gasket
Outlet reduces from 16 to 11 mm; older machines retain the original muffler.
- Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
- Lower-casing exhaust opening reduces from 16 mm (0.63 in) to 11 mm (0.43 in). Muffler 1122 140 0609 becomes 1122 140 0613. This is not a finish-only change.
- NEW MUFFLERS with the smaller exhaust opening MAY ONLY be used on machines with EPA approval. ORIGINAL MUFFLERS should still be used on OLDER MACHINES; the original remains available as a spare under remark 1. Do not treat the new number as universal supersession.
- New gasket 1122 149 0500 is BETWEEN FRONT AND REAR MUFFLER CASINGS, as drawn—not between cylinder and muffler. Use a NEW GASKET whenever the UPPER CASING is removed. The source uses front/rear and upper-casing terminology; the drawing fixes the joint. No torque is given.
- Summary says all other parts as before and introduction in progress. Historical spare availability is not current stock, and this EPA-only restriction must remain visible with replacement numbers.
Source: TI 2/1998, p. 5 · TI 2/1998, p. 6 — Complete section 5, outlet/casing drawing and summary rows 10–11.
Part numbers (3)
- 1122 140 0609 — Original 16 mm-outlet mufflerRetained for older machines · 066; match the version and EPA restrictions in conditions
- 1122 140 0613 — New 11 mm-outlet mufflerEPA-only · 066; match the version and EPA restrictions in conditions
- 1122 149 0500 — Gasket between muffler casingsNew; renew when upper casing removed · 066; match the version and EPA restrictions in conditions
Wrong number or missing part for the 066? Report a correction →