← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section B · 2 of 17 · 24 parts

Cylinder

Fits 066.

Parts diagrams →

Historical fitment & changes (10) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819192202122234567789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 1122 020 1209 Cylinder with piston Ø 54 mm → replaced by 1122 020 1211 TI 27/2003 — 91.6 cc 1
2 1122 020 1211 Cylinder with piston Ø 54 mm Fitment / change note → — 91.6 cc 1
4 1122 030 2005 Piston Ø 54 mm — 91.6 cc 1
5 1122 034 3001 Piston ring Ø 54x1.2 mm — 91.6 cc 2
6 1122 034 1500 Piston pin 12x8x33 1
7 9463 650 1200 Snap ring 12x1 1
8 1122 025 2200 Plug Fitment / change note → 1
9 9022 371 1350 Spline screw IS-M6x25 Fitment / change note → → replaced by 9022 341 1370 TI 3/1999 4
10 1128 020 9400 Decompression valve Fitment / change note → 1
11 1122 084 1405 Cover 1
12 1122 029 2301 Cylinder gasket 0.5 mm Fitment / change note → 1
13 1122 029 2306 Cylinder gasket 1 mm 1
14 1125 007 1021 Spur gear / chain adjusting screw kit 1
15 9646 945 0490 O-ring 7x1.5 1
16 1125 640 1900 Tensioner slide 1
17 1125 664 1400 Thrust pad 1
18 1122 664 2200 Cover plate 1
19 9041 216 0630 Pan head screw M4x8 Fitment / change note → 2
20 1122 664 4500 Support 1
21 1128 664 1001 Inner side plate 0.9 mm Fitment / change note → → replaced by 1128 664 1002 TI 12/1994 1
22 1128 664 1002 NLA Inner side plate Fitment / change note → → replaced by 1128 664 1001, 1128 664 1001 TI 10/2007 option 1
23 9512 003 3281 Needle cage 12x17x13 1
Not numbered on the diagram — assemblies, kits and options
— 1122 007 1053 Set of gaskets 1
— 1122 007 1054 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 044 / 064 / 066

044 / 064 / 066: sprung side plate requires the revised cover

Side plate 1128 664 1001 changes to 1128 664 1002; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.

  • When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
  • The separate 1122-group cover row applies ONLY to 044 and 066 with wrap-around handles. It does not extend that cover to 064 or every 044/066.
  • Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
  • The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
  • The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
  • For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
  • Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
  • Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
  • Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.

Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.

Part numbers (7)
  • 1128 664 1001 — Original side platePrevious version · Retained for original cover
  • 1128 664 1002 — Sprung-tab side plateNew version · Requires new-version cover
  • 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
  • 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
  • 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
  • 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
  • 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping

Historical fitment · 066

066 wrap handle: matched crankshaft, crankcase and seals

The longer crankshaft and revised crankcase form a matched revision; the standard flush-cut Magnum is excluded at this date.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • From X 33 917 066, crankshaft 1122 030 0408 replaces 1122 030 0407 in the wrap-handle modification. The new shaft has a larger big-end bearing, is approximately 4 mm (0.16 in) longer, changes the taper diameter from 13.5 to 15.0 mm (0.53 to 0.6 in), and changes the ignition-end thread from M8 to M10.
  • Crankcase 1122 020 2103 replaces 1122 020 2102 with increased bearing spacing, enlarged oil-seal seat and revised generator seat. Seal BS 13.5×20×4, 9640 003 1355, gives way to BS 15×22×4, 9640 003 1560. The diagrams show the distinct generator mounting seats; no unprinted dimensions are inferred.
  • The bulletin expressly prohibits intermixing original and new-version parts during repairs. A replacement shaft alone is not an approved conversion. The new flywheel also requires the new crankshaft AND crankcase.
  • This line modification does not yet apply to the 066 Magnum with standard flush-cut handle. Summary remark 2 says that version will change later, but supplies no later serial or date.
  • Historical spare availability is retained: old crankcase for older machines; old crankshaft and seal versions for older machines and 064 under remark 3. This does not make the new 066 parts fit 064.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — 1.1–1.2 and summary items 1–4 / remarks 1–3.

Part numbers (6)
  • 1122 030 0407 — Original crankshaftOriginal matched set · Earlier 066 wrap-handle configuration
  • 1122 030 0408 — Longer crankshaftNew matched set · 066 wrap-handle revision only
  • 1122 020 2102 — Original crankcaseOriginal matched set · Earlier 066 configuration
  • 1122 020 2103 — Revised crankcaseNew matched set · 066 wrap-handle revision only
  • 9640 003 1355 — Oil seal BS 13.5×20×4Original seal · Original seat
  • 9640 003 1560 — Oil seal BS 15×22×4Revised seal · Enlarged seat

Service note · 064 / 066

064 / 066: higher cylinder base requires matching longer screws

Cylinder/piston 1122 020 1208 keeps its number; original and revised hardware must not be mixed.

  • The higher cylinder base requires FOUR IS-M6 x 25 spline screws 9022 371 1350 instead of FOUR IS-M6 x 20 screws 9022 371 1300. The cylinder fin is shortened around the mounting screws. A combination of original and new versions is NOT permitted.
  • The summary keeps cylinder with piston 1122 020 1208 unchanged and includes new screw item 2. The part number alone cannot identify base height or approve either screw length. No torque value, cylinder diameter or separate 064/066 cylinder assignment is supplied; do not infer universal cylinder interchange from the two-model heading.
  • TI08/1994 names historical 064 and 066, series 1122, not later MS models. All six changes are in progress; no numeric serial cutoff is supplied. Publication date is January 31, 1994; 08.94 is the bulletin identifier, not an August production date. MOQ columns are commercial order quantities, not installed counts. No physical interchange test was performed.

Source: TI 8/1994, p. 1 — higher cylinder base requires matching longer screws.

Part numbers (3)
  • 1122 020 1208 — Cylinder with piston, same number across revisionunchanged number · higher cylinder base requires matching longer screws
  • 9022 371 1300 — IS-M6 x 20 spline screw, fouroriginal version · higher cylinder base requires matching longer screws
  • 9022 371 1350 — IS-M6 x 25 spline screw, fournew version · higher cylinder base requires matching longer screws

Service note · 066

066: coated steel gasket is single-use and excludes low-compression versions

Install raised side up; do not replace a 1.0 mm low-compression gasket with the 0.5 mm steel gasket.

X 29 588 802 — Printed component-specific introduction, not a universal machine cutoff or unrestricted interchange guarantee.

  • FROM X 29 588 802, coated steel cylinder gasket improves screwed-joint settling behavior. Source specifies 0.06 mm (0.0024 in) rubber coating on BOTH sides for resilience and mating-face unevenness. It calls the steel gasket 0.5 mm; do not calculate a new total thickness from these statements.
  • Install with RAISED SIDE UP as illustrated. Gasket may be used ONCE ONLY; fit a NEW gasket whenever cylinder is removed and refitted. Steel gasket (0.5 mm) MUST NOT be installed in countries using LOW-COMPRESSION machines with 1.0 mm cylinder gasket. No conversion of such machines is authorized.
  • Piston/cylinder 1122 020 1208 and cylinder gasket 1122 029 2301 keep their numbers. Only modified gasket is factory-available. Footnote 2 literally says new version is included in scope of supply of ITEM 2 for approx. TWO YEARS, although item 2 is itself the gasket. Preserve this SELF-REFERENTIAL supply ambiguity, not silently change to item 1 or infer a second gasket. Table separately places gasket under piston/cylinder inclusion.
  • Gasket cutoff X 29 588 802 is not the crankshaft cutoff X 29 588 002 from TI19.94. This TI names 066, not 064 or MS660.
  • Historical TI 22/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 22/1994, p. 1 — 066: coated steel gasket is single-use and excludes low-compression versions.

Part numbers (2)
  • 1122 020 1208 — Piston and cylinder, item 1unchanged number · 066: coated steel gasket is single-use and excludes low-compression versions
  • 1122 029 2301 — Cylinder gasket, item 2unchanged number; modified version · 066: coated steel gasket is single-use and excludes low-compression versions

Service note · 066

066: separate the 0.5 mm gasket before lifting off the cylinder

Separate the gasket from the cylinder base before pulling the cylinder off the piston, to prevent snagging damage.

  • Section 2 explicitly names 066 cylinder/cylinder gasket (0.5 mm), despite the broader 064/066 bulletin heading. It is NOT a 064 instruction or a requirement to replace every gasket with 0.5 mm. No cylinder/gasket order number or serial cutoff is supplied.
  • To avoid possible piston damage from snagging on the gasket edge, ALWAYS separate the gasket from the cylinder base with a screwdriver BEFORE taking the cylinder off the piston. The printed sequence is: loosen and remove FOUR IS M6x25 spline screws from the cylinder; raise the cylinder a little; carefully separate the gasket from the cylinder base flange with a screwdriver; pull the cylinder off the piston.
  • Illustration 137TI002 shows the screwdriver at the slightly raised cylinder base. No pry force, lift distance, tightening torque, sealant or reassembly specification is supplied; none is inferred from the drawing.
  • Refer to and observe “Exposing the Cylinders” in the service manual before this operation. The exact 064/066 service manual was not identified in the retained 74-entry manual catalog or108-PDF cover inventory; the archive docs/resource filename check also found no named manual candidate. This is a bounded source gap, not universal absence. The TI is an addendum, not a complete disassembly procedure.
  • The later 066 cylinder IPL independently lists 0.5 mm and 1 mm gaskets, plus an M6x25 screw with a later TI 03/1999 replacement annotation. Those later rows do not supply a missing 1995 part number or authorize gasket-thickness substitution. Neither the filter introduction cutoff nor the 064 heading is inherited by this 066 service note.
  • Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.

Source: TI 10/1995, p. 1 · TI 10/1995, p. 2 — Sections 1–2: complete two pages, illustrations 132BB001–003 and 137TI002, full summary and remarks.

No additional parts-table entry added.

Service note · 066

066 decompression valve: manual opening and automatic closure

Body, plunger and three detent balls; 13-mm long-reach socket, 14 Nm valve torque, and a separate pressure-test plug.

X 32 231 689 — Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.

  • The valve reduces compression pressure and starter-rope effort during starting. Body (1) contains an axially moving plunger (2) with a conical bottom; THREE spring-loaded balls (3), each offset 120 degrees, hold its upper or lower position. Figure component labels are not the part-summary key numbers. The complete valve screws into the cylinder.
  • Before starting, pushing the plunger DOWN moves the cone away from the body and OPENS the valve. During the upward piston stroke, some gas escapes through the body bore; remaining compression stays below closing pressure. Only after ignition does cylinder pressure exceed closing pressure, pushing the plunger UP and closing the bore. Automatic closure is not a claim that rope cranking alone closes it. No numerical closing pressure is supplied.
  • The service note specifies a standard commercial LONG-REACH 13-mm socket for valve removal/installation and tightening torque 14 Nm (10.3 lbf.ft). That is VALVE torque, not cylinder-fastener or blanking-plug torque. No thread sealant or additional tightening step is supplied here.
  • For the engine pressure test, the TI recommends REMOVING THE DECOMPRESSION VALVE and sealing its tapped hole with plug 1122 025 2200. This is distinct from cap 1122 084 7100 closing a SHROUD opening on a machine without the valve. No test pressure, duration or complete engine-testing procedure is supplied.
  • Table key 3 identifies decompression valve 1128 020 9400, MOQ H 1; key 2 is plug 1122 025 2200, MOQ H 5. MOQ 5 does not mean five plugs per cylinder. Later 066 B sheet keys 10 and 8 respectively corroborate these numbers, not the universal suitability of other valves sharing a similar body.
  • Historical TI guidance for model 066 only, subject to the stated version restrictions; shared series or part numbers do not extend this guidance to successor models. No present-day stock guarantee, physical interchange verification or model-identification serial interval is implied. No hardware operation was performed.

Source: TI 22/1995, p. 1 · TI 22/1995, p. 2 · TI 22/1995, p. 3 — Section 1 complete operating explanation, figures 137TI006/007/008, service note and valve/plug rows.

Part numbers (2)
  • 1128 020 9400 — Decompression valvetable key 3; MOQ 1; valve torque 14 Nm · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.
  • 1122 025 2200 — Cylinder threaded-hole plugtable key 2; MOQ 5; pressure-test blanking plug · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.

Service note · 066

066 cylinder change: 1208 to 1210, including the plug

Keep the 1995 cylinder pair separate from later 1209/1211 catalog entries and the separately listed valve.

X 32 231 689 — Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.

  • The original cylinder with piston 1122 020 1208 becomes 1122 020 1210, table key 1, MOQ H 1. “Including item 2” refers to PLUG 1122 025 2200, NOT the separately listed decompression valve at item 3. Do not silently substitute the valve for the included plug.
  • Remark 1 says the ORIGINAL CYLINDER remains factory-supplied only while EXISTING STOCKS LAST. This is a 1995 supply statement, not current availability or a guarantee that every old machine can take the new cylinder without further checks. The TI does not provide a cylinder bore, piston dimension or a complete conversion-kit list.
  • Later 066 B cylinder sheet keys 1 and 2 list 1122 020 1209 and 1122 020 1211, not this TI’s 1208 and 1210. Retain both pairs as edition-specific evidence; no undocumented 1208-to-1209 or 1210-to-1211 supersession is inferred. Later sheet keys 8/10 do corroborate the plug and valve numbers.
  • The summary says ALL OTHER PARTS AS BEFORE. That does not remove the explicit shroud/cover/cap changes in the same table or authorize extending the 066 change to 064 or MS 660.
  • Historical TI guidance for model 066 only, subject to the stated version restrictions; shared series or part numbers do not extend this guidance to successor models. No present-day stock guarantee, physical interchange verification or model-identification serial interval is implied. No hardware operation was performed.

Source: TI 22/1995, p. 1 · TI 22/1995, p. 3 — Section 1 introduction and complete cylinder/plug/valve summary rows with remark 1.

Part numbers (3)
  • 1122 020 1208 — Original cylinder with pistontable key 1; historical factory stocks only · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.
  • 1122 020 1210 — New cylinder with pistontable key 1; includes item 2 plug; MOQ 1 · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.
  • 1122 025 2200 — Plugincluded item 2; separate order MOQ 5 · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.

Service note · 066

066: raised cylinder-gasket side faces crankcase; single use

1122 029 2301 must be renewed after cylinder disassembly; 064 is outside this section.

  • Section6 is specifically 066 CYLINDER GASKET, despite the two-model bulletin heading. Cylinder gasket(1)1122 029 2301 must be installed with its RAISED SIDE FACING THE CRANKCASE(2) to reduce cylinder-base load. Figure137TI019 identifies gasket1 and crankcase2; do not reverse the embossed side.
  • The gasket may be used ONCE ONLY. Always install a NEW gasket after disassembling the cylinder. No reuse exception, sealant, tightening torque or full cylinder-disassembly procedure is supplied. The TI does not supply a thickness; later IPL thickness is not silently imported into this instruction.
  • The extracted text corrupts this part number as NNOO=MOV=OPMN. The original scan clearly prints1122 029 2301; scan transcription is pinned to page4 section6 rather than silently replacing the canonical body.
  • Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.

Source: TI 8/1997, p. 4 — 066: raised cylinder-gasket side faces crankcase; single use.

Part numbers (1)
  • 1122 029 2301 — 066 cylinder-base gasketSingle-use; raised side toward crankcase · 066; only the described configuration

Service note · 066

066 crankshaft ignition end: service tool and screw sleeve

Both 5910 890 2220 and 5910 893 2421 are specified for removal and installation.

X 33 917 066 — TI15/1997 service-note boundary for the referenced revised 066 configuration; not a universal flush-cut/064/successor cutoff.

  • For CRANKSHAFT, IGNITION END, use service tool 5910 890 2220 (1) AND screw sleeve 5910 893 2421 (2) for removal AND installation. These are separate numbered tools, not alternate choices or a single combined part number.
  • Drawing 137TI020 KN labels the plate/tool (1) and upright screw sleeve (2); 137TI021 KN shows the tool assembly at the crankcase. These pictures do not specify the mounting-hole selection, a clutch-side procedure, tightening torque or operating-force limit. This screw sleeve is NOT the oil-seal press sleeve 1122 893 2405.
  • TI15/1997 applies these service notes to model 066 from machine number X 33 917 066 and explicitly refers to the TI02/1996 engineering changes: larger big-end bearing, wider-spaced crankcase bearings and lightweight flywheel. The notes supplement the 064, 066 shop manual; naming that joint manual does NOT extend the modification to 064 or MS successors.
  • Scope tension retained: TI15/1997 says 066 without repeating the handle qualifier; cited TI02/1996 sections 1 and 2 say WRAP HANDLE ONLY and exclude the standard flush-cut 066 Magnum at that date. Its summary says that version changes later but gives no date or cutoff. TI15 does not establish that later introduction. Identify the revised configuration; the serial alone is not proof of universal fitment. TI02 forbids mixing old/new crank-drive parts and requires the new crankshaft AND crankcase with the lightweight flywheel.
  • TI15 page 2 delegates detailed use of the special tools to the existing 064, 066 shop manual. That exact manual is not established in the verified local STIHL service documentation/owner PDF pools; detailed procedure remains a documented source gap. Later MS650/660 workshop material and the 2012 general tool catalogue are not treated as the missing historical manual. No unprinted torque, force, thread engagement, seal depth or complete repair sequence is supplied here. Last-TI08/1997 is bibliographic context, not a dependent procedure.
  • Tool numbers below are transcribed from the original scans; the retained extracted text has corrupted font-encoded digits. Originals and extraction remain unchanged. Historical source guidance only; no current availability, physical interchange or hardware execution established. No hardware operation was performed.

Source: TI 15/1997, p. 1 · TI 15/1997, p. 2 — 066 crankshaft ignition end: service tool and screw sleeve.

Referenced bulletin evidence: TI 2/1996, p. 1 · TI 2/1996, p. 2 · TI 2/1996, p. 4 — Referenced configuration only: sections1.1/1.2/2.1 and summary remark2.

Part numbers (2)
  • 5910 890 2220 — Service tool, drawing item 1Crankshaft ignition-end removal and installation · 066 revised configuration described in TI15/1997; ignition end only where specified
  • 5910 893 2421 — Screw sleeve, drawing item 2Used with service tool 5910 890 2220 · 066 revised configuration described in TI15/1997; ignition end only where specified

Conditional replacement · 066

066: revised cylinder ports retain bore, stroke and mounting dimensions

1122 020 1211 replaces 1210; changed timing works with the muffler changes.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • Cylinder-port modifications change timing to optimize combustion; together with section 5 muffler changes they reduce emissions to the specified limits. Bore, stroke and mounting dimensions remain as before.
  • Cylinder WITH PISTON changes 1122 020 1210 → 1122 020 1211. Original assembly remains a spare under remark 1. No piston-only number, port dimensions or timing angles are supplied; unchanged mounting dimensions alone do not prove unrestricted cylinder/muffler combinations.

Source: TI 2/1998, p. 4 · TI 2/1998, p. 6 — Section 3, summary row 8 and remark 1.

Part numbers (2)
  • 1122 020 1210 — Cylinder with pistonOriginal, retained spare · 066; match the version and EPA restrictions in conditions
  • 1122 020 1211 — Cylinder with piston, modified portsNew · 066; match the version and EPA restrictions in conditions

Wrong number or missing part for the 066? Report a correction →