← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section P · 15 of 17 · 39 parts

Carburetor WJ-69B

Fits 066.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922020222323242425262728293303132333435363738456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (39)

PosPart numberDescriptionQty
1 1122 121 5603 Fixed jet 0.62 Fitment / change note → 1
2 1110 121 5100 Inlet needle 1
3 1117 122 3005 Spring 1
4 1117 121 9200 Spindle 1
5 1117 121 5000 Inlet control lever 1
6 1114 122 7400 Round head screw 1
7 1115 121 5401 Valve jet 1
8 1122 121 0700 Cup plug 1
9 1116 129 0900 Gasket 1
10 1117 121 4700 Metering diaphragm 1
11 1122 121 0805 End cover 1
12 1121 122 7101 Screw 4
13 1114 121 7800 Strainer 1
14 1115 121 4800 Pump diaphragm 1
15 1115 129 1100 Gasket 1
16 1115 120 0800 End cover 1
17 1121 122 7101 Screw 4
18 1115 121 3301 Throttle shutter 1
19 1122 121 2900 Choke shutter 1
20 1115 122 7400 Round head screw 2
22 1122 122 6703 High speed adjustment screw Fitment / change note → 1
23 4203 122 3600 Sealing ring 2
24 4203 121 2700 Cap Fitment / change note → 2
25 1122 122 6200 Idle speed adjustment screw 1
26 1122 122 3200 Torsion spring 1
27 1122 120 7101 Throttle shaft with lever 1
28 1110 122 9300 Clip 1
29 1106 122 7400 Round head screw 1
30 1122 122 3205 Torsion spring 1
31 1122 120 7200 Choke shaft with lever 1
32 1117 122 9000 E-clip 1
33 1122 121 7700 Clamp 1
34 5910 890 4500 Puller Fitment / change note → option 1
35 1122 121 5602 Fixed jet 0.72 1
36 1115 121 0700 Cup plug 1
37 1122 122 6702 High speed adjustment screw 1
38 1122 122 6705 High speed adjustment screw 1
Not numbered on the diagram — assemblies, kits and options
— 1122 120 0618 NLA Carburetor WJ-69B Fitment / change note → 1
— 1122 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 066

066: WJ-69 EPA carburetor and version-specific components

WJ-69 replaces WJ-65; jet 62 becomes jet 64 in this TI, not the later IPL.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • WJ-65 1122 120 0616 becomes WJ-69 1122 120 0618. WJ-69 carries remark 2: ONLY machines with EPA approval. Original WJ-65 remains a spare under remark 1; it is not declared discontinued.
  • Page 1 figure items: 1 H screw and 2 L screw have knurled heads to hold caps; 3 caps restrict adjustment; 4 O-rings seal screws to body; 5 insert bores have molded stops. These figure numbers differ from page 6 summary numbers.
  • Summary row 1 H screw 1122 122 6706 → 1122 122 6703; row 3 L screw 1122 122 6802 → 1122 122 6803. Each screw includes row 2 O-ring. Row 2 appears twice with -*- instead of an order number; remark 3 says no longer available as replacement. Do not invent an O-ring number or a separately orderable replacement.
  • Row 3 low-speed-screw line also carries remark 2, EPA-only. Preserve that row-level restriction; do not infer unrestricted interchange from matching screw descriptions. Original H screw has remark 1 retaining it as a spare.
  • Old-only row 4 fixed jet 62 is 1122 121 5603; new-only row 5 fixed jet 64 is 1122 121 5604. Row 6 adds TWO caps 4203 121 2700. Heading each carburetor includes items 1–6 does not override the old/new dashes or merge both jets into one version. All other parts as before.
  • The later IPL calls the same complete numbers WJ-65A and WJ-69B. Its WJ-69B sheet lists fixed jet 0.62 (1122 121 5603), whereas this TI assigns 64 (1122 121 5604) to new WJ-69. Keep that version/jet discrepancy explicit, not a silent correction or permission to change jets.

Source: TI 2/1998, p. 1 · TI 2/1998, p. 6 — Sections 1/1.1, five function items and summary carburetor rows 1–6/remarks.

Part numbers (9)
  • 1122 120 0616 — WJ-65 assemblyOriginal, retained spare · 066; match the version and EPA restrictions in conditions
  • 1122 120 0618 — WJ-69 assemblyNew, EPA-only · 066; match the version and EPA restrictions in conditions
  • 1122 122 6706 — H screw including O-ringOriginal, retained spare · 066; match the version and EPA restrictions in conditions
  • 1122 122 6703 — H screw including O-ringNew · 066; match the version and EPA restrictions in conditions
  • 1122 122 6802 — L screw including O-ringOriginal column, row carries EPA restriction · 066; match the version and EPA restrictions in conditions
  • 1122 122 6803 — L screw including O-ringNew column, row carries EPA restriction · 066; match the version and EPA restrictions in conditions
  • 1122 121 5603 — Fixed jet 62Original, retained spare · 066; match the version and EPA restrictions in conditions
  • 1122 121 5604 — Fixed jet 64New · 066; match the version and EPA restrictions in conditions
  • 4203 121 2700 — Limiter cap, twoNew · 066; match the version and EPA restrictions in conditions

Service note · 066

066: capped standard setting starts at the lean stops

H 3/4 and L 1/4 open from the lean stops; each cap permits 270° travel.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • The factory optimum and owner-manual standard are H = 3/4 turn open, L = 1/4 turn open, STARTING FROM THE LEAN STOP in each case. This is not the cap-off, seat-based basic setting.
  • Integrally molded bore stops permit 270° adjustment of each cap. This allows leaner high-altitude correction if needed and helps prevent enrichment beyond EPA emission limits.
  • Only if the engine runs unsatisfactorily at higher altitude: check standard setting, warm engine, then turn H and L clockwise (leaner) as needed within permitted travel. Too lean a setting exceeds maximum permissible engine speed and may damage the engine. No numerical maximum speed is specified here.

Source: TI 2/1998, p. 2 — Section 1.2 including 270° diagram, altitude correction and warning.

No additional parts-table entry added.

Service note · 066

066: single-use cap removal and uncapped basic setting

Both screws open one full turn from lightly seated; new caps must match the original lug diagram.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • To replace adjusting screws or clean the carburetor, remove caps with puller 5910 890 4500. Rotate caps/screws COUNTERCLOCKWISE to the stop; screw the puller into each cap COUNTERCLOCKWISE until it comes off.
  • Caps are damaged during disassembly and MUST NOT be reused. After fitting screws, with caps OFF and screws LIGHTLY against their seats, open H ONE FULL TURN and L ONE FULL TURN.
  • Always fit NEW caps. Insert them with lug positions exactly as shown by the arrows in original figure 137TI036 KN on page 3, then push until flush with insert 1. LA is below the H/L pair in that view. No guessed orientation from another model is substituted.
  • This cap/screw position equals the capped standard in section 1.2. The full-turn seat-based basic setting and fractional lean-stop standard have different reference points.

Source: TI 2/1998, p. 2 · TI 2/1998, p. 3 — Sections 1.3/1.3.1/1.3.2 including puller and lug-position drawings.

Part numbers (1)
  • 5910 890 4500 — Limiter-cap pullerServicing tool · 066; match the version and EPA restrictions in conditions

Service note · 066

066: 2,500 rpm idle and 50:1 emission-approval evidence

Use a tachometer for LA adjustment; TI27 emission details remain a source gap.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • Set engine idle speed to 2,500 rpm with idle-speed screw LA; USE A TACHOMETER. LA is distinct from mixture screws H and L.
  • EPA approval was obtained with 50:1 fuel/oil mix. The TI says no emission measurements are available for other ratios; it does not establish equivalent emissions for another mix.
  • The factory applies the illustrated U.S. EPA Phase 1 engine-information label to machines conforming to the modified standard. The specimen’s family/type/displacement/date placeholders are not an individual machine identity or a numeric production cutoff.
  • TI27/1997 is delegated for emission and Federal Emission Control Systems Utility Engines details. It is absent from retained 690 TIs and the current 766-PDF resource filename inventory; bounded absence reverified this batch. Missing text is not fabricated. Last-TI 01.98 footer is bibliographic, not a delegated repair procedure.

Source: TI 2/1998, p. 1 · TI 2/1998, p. 3 — Cover label and sections 1.3.3/1.4/1.5.

No additional parts-table entry added.

Conditional replacement · 066

066: new screwdriver guide fits flush with limiter caps

1122 123 7501 accompanies the new carburetor and replaces 7500.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • Grommet 1122 123 7501 replaces 1122 123 7500 together with the new carburetor. It guides the carburetor screwdriver, fits the illustrated carburetor recess and is flush with limiter caps. H, L and LA markings in the drawing identify controls; they are not new mixture settings.
  • Original grommet remains available as a spare under remark 1. Match actual carburetor/guide geometry; no stand-alone universal retrofit is established.

Source: TI 2/1998, p. 4 · TI 2/1998, p. 6 — Section 2 and drawing 137TI037 KN, summary row 7/remark 1.

Part numbers (2)
  • 1122 123 7500 — Original screwdriver guide grommetRetained original spare · 066; match the version and EPA restrictions in conditions
  • 1122 123 7501 — Shaped guide grommetNew · 066; match the version and EPA restrictions in conditions

Wrong number or missing part for the 066? Report a correction →