Stihl 1122 · Section O · 14 of 17 · 40 parts
Carburetor WJ-65A, WJ-67A, WJ-76A
Fits 066.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 121 5604 | Fixed jet 0.64 Fitment / change note → | 1 |
| 2 | 1122 121 5607 | Fixed jet 0.74 | 1 |
| 3 | 1110 121 5100 | Inlet needle | 1 |
| 4 | 1117 122 3005 | Spring | 1 |
| 5 | 1117 121 9200 | Spindle | 1 |
| 6 | 1117 121 5000 | Inlet control lever | 1 |
| 7 | 1114 122 7400 | Round head screw | 1 |
| 8 | 1115 121 5401 | Valve jet | 1 |
| 9 | 1122 121 0700 | Cup plug Fitment / change note → | 1 |
| 10 | 1116 129 0900 | Gasket | 1 |
| 11 | 1117 121 4700 | Metering diaphragm | 1 |
| 12 | 1122 121 0805 | End cover | 1 |
| 13 | 1121 122 7101 | Screw | 4 |
| 14 | 1115 121 3301 | Throttle shutter | 1 |
| 15 | 1115 122 7400 | Round head screw | 2 |
| 16 | 1128 122 3003 | Spring Fitment / change note → | 2 |
| 18 | 1122 122 6802 | Low speed adjustment screw Fitment / change note → | 1 |
| 19 | 1122 122 6706 | High speed adjustment screw Fitment / change note → | 1 |
| 20 | 4203 122 3600 | Sealing ring Fitment / change note → | 2 |
| 21 | 1122 122 6200 | Idle speed adjustment screw | 1 |
| 22 | 1122 122 3200 | Torsion spring | 1 |
| 23 | 1122 120 7101 | Throttle shaft with lever | 1 |
| 25 | 1106 122 7400 | Round head screw | 1 |
| 26 | 1122 122 3205 | Torsion spring | 1 |
| 27 | 1122 120 7200 | Choke shaft with lever | 1 |
| 28 | 1117 122 9000 | E-clip | 1 |
| 29 | 1114 121 7800 | Strainer | 1 |
| 30 | 1115 121 4800 | Pump diaphragm | 1 |
| 31 | 1115 129 1100 | Gasket | 1 |
| 32 | 1115 120 0800 | End cover | 1 |
| 33 | 1121 122 7101 | Screw | 4 |
| 34 | 1122 121 2900 | Choke shutter | 1 |
| 35 | 1122 121 7700 | Clamp | 1 |
| 36 | 1122 121 5603 | Fixed jet 0.62 Fitment / change note → option | 1 |
| 37 | 1122 121 5601 | Fixed jet 0.66 | 1 |
| 38 | 1122 122 6705 | High speed adjustment screw Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 120 0621 | Carburetor WJ-67A Fitment / change note → → replaced by 1122 120 0618 TI 27/2003 | 1 |
| — | 1122 120 0623 | Carburetor WJ-76A | 1 |
| — | 1122 007 1060 | Set of carburetor parts | 1 |
| — | 1122 120 0616 | Carburetor WJ-65A Fitment / change note → → replaced by 1122 120 0621, 1122 120 0618 TI 1/1998 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 066
066 non-EPA carburetors: WJ-65 / WJ-51 to WJ-67
WJ-67 1122 120 0621 replaces WJ-65 on 066 and WJ-51 on 066 Magnum only on machines without EPA approval.
X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.
- This standardization explicitly applies only to machines without EPA approval, including older 066 and 066 M (Magnum). Do not apply it to an EPA carburetor or infer a 064 application from the imported index title; the original cover names model 066.
- The 1998 designations are WJ-65, WJ-51 and WJ-67. Later A suffixes in the current assembly title do not silently rename the source versions or prove identical internal parts.
- The 066 WJ-67 row prints includes items 1 and 2 although fixed jet 62 is in the original column and fixed jet 64 in the new column. Preserve that inclusion wording without interpreting it as an instruction to install both jets or as a tuning choice.
- The 066 Magnum WJ-67 row includes items 3–6: high-speed screw, low-speed screw (printed lower speed screw), spring and sealing ring. The shared complete-carburetor number does not erase those summary distinctions.
- Remark 1 keeps original WJ-65, fixed jet 62 and the original high-/low-speed screws available as spares; remark 2 says fixed jet 64 is already in inventory. Original spring remains for older machines under remark 4. No separate availability remark is printed beside WJ-51. These are historical supply statements, not current stock.
- The summary prints introduction from X39 176186 for the modification, but section 1 expressly also describes replacements for older non-EPA machines. That serial does not exclude the stated older-machine replacement or authorize an EPA conversion. No carburetor setting is supplied here.
Source: TI 1/1998, p. 1 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Section1 and complete carburetor summary rows, items1–6 and remarks.
Part numbers (12)
- 1122 120 0616 — WJ-65 carburetorOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 120 0614 — WJ-51 carburetor (066 Magnum)Original version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 120 0621 — WJ-67 carburetorNew version · 066; exact 1998 configuration and conditions apply
- 1122 121 5603 — Fixed jet 62Original version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 121 5604 — Fixed jet 64New version · 066; exact 1998 configuration and conditions apply
- 1122 122 6704 — High-speed screwOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 122 6706 — High-speed screwNew version · 066; exact 1998 configuration and conditions apply
- 1122 122 6801 — Low-speed screwOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1122 122 6802 — Low-speed screwNew version · 066; exact 1998 configuration and conditions apply
- 1115 122 3002 — SpringOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
- 1128 122 3003 — SpringNew version · 066; exact 1998 configuration and conditions apply
- 4203 122 3600 — Sealing ringNew version · 066; exact 1998 configuration and conditions apply
Service note · 066
066 Standard: WJ 41 to WJ 48 carburetor
EY-V adaptation changes fixed jet, high-speed screw and cup plug; carburetor introduction precedes ignition.
X 31 067 138 — 066 adapted carburetor only; not the ignition/flywheel cutoff or a model-production range.
- Page 4 assigns WJ 48 to 066 Standard. The table replaces WJ 41 1122 120 0607 with WJ 48 1122 120 0616; both assembly headings say they include items 1–4. New complete carburetor MOQ 1. No new interchangeable repair-kit number is given.
- Fixed jet 0.72 mm 1122 121 5602 becomes 0.62 mm 1122 121 5603. High speed adjusting screw 1122 122 6702 becomes 1122 122 6705. Cup plug 1115 121 0700 becomes 1122 121 0700. All three old component types remain available for older machines (remark 2); each new component has MOQ 1.
- Figure 134TI002 identifies the fixed-jet marking 62 for WJ 48 and 64 for WJ 51/52. Those markings represent 0.62/0.64 mm jets, not 62/64 mm bores or carburetor identities by themselves.
- Original WJ 41 has remark 1: no longer available from factory.
- Carburetor cutoff X 31 067 138 is for 066; page 4 prints only the 064 cutoff, while page 5 supplies BOTH model cutoffs. Neither equals ignition/flywheel cutoff X 31 067 164. Do not rewrite the earlier carburetor introduction to make a single simultaneous conversion boundary.
- The exact-model 2012 carburetor sheet is a navigation context, NOT identification with its later WJ-65A/WJ-67A/WJ-76A configurations. In particular 1122 120 0616 is labeled WJ 48 here but WJ-65A in the later IPL; the shared number does not prove identical calibration or supersession. Preserve the historical jet/screw assignments; no complete current tuning or retrofit procedure is supplied.
- Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.
Source: TI 51/1994, p. 4 · TI 51/1994, p. 5 — 066 Standard: WJ 41 to WJ 48 carburetor.
Part numbers (8)
- 1122 120 0607 — Original WJ 41 carburetororiginal; availability as qualified · 066 only in the exact version/configuration described here
- 1122 120 0616 — New WJ 48 carburetorincludes items 1–4; MOQ 1 · 066 only in the exact version/configuration described here
- 1122 121 5602 — Original fixed jet 0.72 mmolder machines · 066 only in the exact version/configuration described here
- 1122 121 5603 — New fixed jet 0.62 mmMOQ 1 · 066 only in the exact version/configuration described here
- 1122 122 6702 — Original high-speed screwolder machines · 066 only in the exact version/configuration described here
- 1122 122 6705 — New high-speed screwMOQ 1 · 066 only in the exact version/configuration described here
- 1115 121 0700 — Original cup plugolder machines · 066 only in the exact version/configuration described here
- 1122 121 0700 — New cup plugMOQ 1 · 066 only in the exact version/configuration described here
Service note · 066
066 Magnum / USA-CDN table: WJ 35 to WJ 51 carburetor
EY-V adaptation changes fixed jet, high-speed screw and cup plug; carburetor introduction precedes ignition.
X 31 067 138 — 066 adapted carburetor only; not the ignition/flywheel cutoff or a model-production range.
- Page 4 assigns WJ 51 to 066 Magnum; page 5 labels the WJ 35/51 table USA/CDN. The table replaces WJ 35 1122 120 0611 with WJ 51 1122 120 0614; both assembly headings say they include items 1–4. New complete carburetor MOQ 1. No new interchangeable repair-kit number is given.
- Fixed jet 0.72 mm 1122 121 5602 becomes 0.64 mm 1122 121 5604. High speed adjusting screw 1122 122 6705 becomes 1122 122 6704. Cup plug 1115 121 0700 becomes 1122 121 0700. All three old component types remain available for older machines (remark 2); each new component has MOQ 1.
- Figure 134TI002 identifies the fixed-jet marking 62 for WJ 48 and 64 for WJ 51/52. Those markings represent 0.62/0.64 mm jets, not 62/64 mm bores or carburetor identities by themselves.
- The WJ 35 original-carburetor row has NO availability remark; do not transfer the WJ 41/WJ 42 factory-unavailability note to WJ 35. Page 4 says Magnum, whereas the WJ 35/51 table labels USA/CDN; retain both descriptions without equating all Magnum and USA/CDN configurations.
- Carburetor cutoff X 31 067 138 is for 066; page 4 prints only the 064 cutoff, while page 5 supplies BOTH model cutoffs. Neither equals ignition/flywheel cutoff X 31 067 164. Do not rewrite the earlier carburetor introduction to make a single simultaneous conversion boundary.
- The exact-model 2012 carburetor sheet is a navigation context, NOT identification with its later WJ-65A/WJ-67A/WJ-76A configurations. In particular 1122 120 0616 is labeled WJ 48 here but WJ-65A in the later IPL; the shared number does not prove identical calibration or supersession. Preserve the historical jet/screw assignments; no complete current tuning or retrofit procedure is supplied.
- Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.
Source: TI 51/1994, p. 4 · TI 51/1994, p. 5 — 066 Magnum / USA-CDN table: WJ 35 to WJ 51 carburetor.
Part numbers (8)
- 1122 120 0611 — Original WJ 35 carburetororiginal; availability as qualified · 066 only in the exact version/configuration described here
- 1122 120 0614 — New WJ 51 carburetorincludes items 1–4; MOQ 1 · 066 only in the exact version/configuration described here
- 1122 121 5602 — Original fixed jet 0.72 mmolder machines · 066 only in the exact version/configuration described here
- 1122 121 5604 — New fixed jet 0.64 mmMOQ 1 · 066 only in the exact version/configuration described here
- 1122 122 6705 — Original high-speed screwolder machines · 066 only in the exact version/configuration described here
- 1122 122 6704 — New high-speed screwMOQ 1 · 066 only in the exact version/configuration described here
- 1115 121 0700 — Original cup plugolder machines · 066 only in the exact version/configuration described here
- 1122 121 0700 — New cup plugMOQ 1 · 066 only in the exact version/configuration described here
Service note · 066
066 carburetor heating (Arctic / VH): WJ 42 to WJ 52 carburetor
EY-V adaptation changes fixed jet, high-speed screw and cup plug; carburetor introduction precedes ignition.
X 31 067 138 — 066 adapted carburetor only; not the ignition/flywheel cutoff or a model-production range.
- Page 4 assigns WJ 52 to 066 with carburetor heating (Arctic); page 5 labels the WJ 42/52 table VH. The table replaces WJ 42 1122 120 0609 with WJ 52 1122 120 0615; both assembly headings say they include items 1–4. New complete carburetor MOQ 1. No new interchangeable repair-kit number is given.
- Fixed jet 0.72 mm 1122 121 5602 becomes 0.64 mm 1122 121 5604. High speed adjusting screw 1122 122 6705 becomes 1122 122 6704. Cup plug 1115 121 0700 becomes 1122 121 0700. All three old component types remain available for older machines (remark 2); each new component has MOQ 1.
- Figure 134TI002 identifies the fixed-jet marking 62 for WJ 48 and 64 for WJ 51/52. Those markings represent 0.62/0.64 mm jets, not 62/64 mm bores or carburetor identities by themselves.
- Original WJ 42 has remark 1: no longer available from factory.
- Carburetor cutoff X 31 067 138 is for 066; page 4 prints only the 064 cutoff, while page 5 supplies BOTH model cutoffs. Neither equals ignition/flywheel cutoff X 31 067 164. Do not rewrite the earlier carburetor introduction to make a single simultaneous conversion boundary.
- The exact-model 2012 carburetor sheet is a navigation context, NOT identification with its later WJ-65A/WJ-67A/WJ-76A configurations. In particular 1122 120 0616 is labeled WJ 48 here but WJ-65A in the later IPL; the shared number does not prove identical calibration or supersession. Preserve the historical jet/screw assignments; no complete current tuning or retrofit procedure is supplied.
- Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.
Source: TI 51/1994, p. 4 · TI 51/1994, p. 5 — 066 carburetor heating (Arctic / VH): WJ 42 to WJ 52 carburetor.
Part numbers (8)
- 1122 120 0609 — Original WJ 42 carburetororiginal; availability as qualified · 066 only in the exact version/configuration described here
- 1122 120 0615 — New WJ 52 carburetorincludes items 1–4; MOQ 1 · 066 only in the exact version/configuration described here
- 1122 121 5602 — Original fixed jet 0.72 mmolder machines · 066 only in the exact version/configuration described here
- 1122 121 5604 — New fixed jet 0.64 mmMOQ 1 · 066 only in the exact version/configuration described here
- 1122 122 6705 — Original high-speed screwolder machines · 066 only in the exact version/configuration described here
- 1122 122 6704 — New high-speed screwMOQ 1 · 066 only in the exact version/configuration described here
- 1115 121 0700 — Original cup plugolder machines · 066 only in the exact version/configuration described here
- 1122 121 0700 — New cup plugMOQ 1 · 066 only in the exact version/configuration described here
Service note · 064 / 066
064 / 066: revised 13000 rpm maximum with bar and chain
The historical maximum is measured with guide bar and properly tensioned chain, not as a bare-powerhead speed.
- Maximum permissible speed changes: 064 from 12,000 to 13,000 rpm; 066 CDIC A from 13,500 rpm CUT-OFF speed to 13,000 rpm; 066 USA/CDN from 13,500 to 13,000 rpm. These old values belong to their named ignition variants; do not infer that all original modules had electronic governors.
- ALL engine speeds are measured with GUIDE BAR and PROPERLY TENSIONED CHAIN. This is not a bare-powerhead limit or a replacement for exact-version servicing instructions. The ungoverned EY-V has no implied automatic 13,000 rpm limiter.
- The separate 900 rpm ignition cut-in is not an idle speed. No idle setting, H-screw turns or target-specific numerical air gap is supplied. No engine was run or adjusted.
- Footer refers to previous TI 45.94 on 064/066 and is dated December 15, 1994. This is a prior-information pointer, not a required missing retrofit document or proof of blanket later-model applicability.
- Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.
Source: TI 51/1994, p. 4 · TI 51/1994, p. 5 — 064 / 066: revised 13000 rpm maximum with bar and chain.
No additional parts-table entry added.
Conditional replacement · 066
066: WJ-69 EPA carburetor and version-specific components
WJ-69 replaces WJ-65; jet 62 becomes jet 64 in this TI, not the later IPL.
- Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
- WJ-65 1122 120 0616 becomes WJ-69 1122 120 0618. WJ-69 carries remark 2: ONLY machines with EPA approval. Original WJ-65 remains a spare under remark 1; it is not declared discontinued.
- Page 1 figure items: 1 H screw and 2 L screw have knurled heads to hold caps; 3 caps restrict adjustment; 4 O-rings seal screws to body; 5 insert bores have molded stops. These figure numbers differ from page 6 summary numbers.
- Summary row 1 H screw 1122 122 6706 → 1122 122 6703; row 3 L screw 1122 122 6802 → 1122 122 6803. Each screw includes row 2 O-ring. Row 2 appears twice with -*- instead of an order number; remark 3 says no longer available as replacement. Do not invent an O-ring number or a separately orderable replacement.
- Row 3 low-speed-screw line also carries remark 2, EPA-only. Preserve that row-level restriction; do not infer unrestricted interchange from matching screw descriptions. Original H screw has remark 1 retaining it as a spare.
- Old-only row 4 fixed jet 62 is 1122 121 5603; new-only row 5 fixed jet 64 is 1122 121 5604. Row 6 adds TWO caps 4203 121 2700. Heading each carburetor includes items 1–6 does not override the old/new dashes or merge both jets into one version. All other parts as before.
- The later IPL calls the same complete numbers WJ-65A and WJ-69B. Its WJ-69B sheet lists fixed jet 0.62 (1122 121 5603), whereas this TI assigns 64 (1122 121 5604) to new WJ-69. Keep that version/jet discrepancy explicit, not a silent correction or permission to change jets.
Source: TI 2/1998, p. 1 · TI 2/1998, p. 6 — Sections 1/1.1, five function items and summary carburetor rows 1–6/remarks.
Part numbers (9)
- 1122 120 0616 — WJ-65 assemblyOriginal, retained spare · 066; match the version and EPA restrictions in conditions
- 1122 120 0618 — WJ-69 assemblyNew, EPA-only · 066; match the version and EPA restrictions in conditions
- 1122 122 6706 — H screw including O-ringOriginal, retained spare · 066; match the version and EPA restrictions in conditions
- 1122 122 6703 — H screw including O-ringNew · 066; match the version and EPA restrictions in conditions
- 1122 122 6802 — L screw including O-ringOriginal column, row carries EPA restriction · 066; match the version and EPA restrictions in conditions
- 1122 122 6803 — L screw including O-ringNew column, row carries EPA restriction · 066; match the version and EPA restrictions in conditions
- 1122 121 5603 — Fixed jet 62Original, retained spare · 066; match the version and EPA restrictions in conditions
- 1122 121 5604 — Fixed jet 64New · 066; match the version and EPA restrictions in conditions
- 4203 121 2700 — Limiter cap, twoNew · 066; match the version and EPA restrictions in conditions
Wrong number or missing part for the 066? Report a correction →