← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section Q · 16 of 17 · 25 parts

Shroud, Air filter

Fits 066.

Parts diagrams →

Historical fitment & changes (15) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718191922020212223243456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (25)

PosPart numberDescriptionQty
1 1122 080 1607 Shroud Fitment / change note → 1
2 1122 967 1505 Model plate 066 Fitment / change note → → replaced by 1122 967 1506 TI 53/2002 1
3 1121 084 7100 Cap 1
4 1124 084 8300 Reflector foil 1
5 0000 963 0808 Bushing 3
6 1122 084 7101 Cap 1
7 0000 967 1593 Model plate Magnum 1
8 1122 120 3402 Filter base Fitment / change note → 1
9 1122 120 2200 Flange Fitment / change note → 1
10 9121 319 0960 Stud M5x12x9 Fitment / change note → 1
11 9216 261 0700 Hexagon nut M5 2
12 1122 121 6900 Baffle Fitment / change note → 1
13 1122 141 6300 Air baffle Fitment / change note → 1
14 0000 140 4402 Air filter HD2 1
15 0000 141 0300 Prefilter Fitment / change note → 1
16 0000 120 1653 Air filter, wire mesh option 1
17 1122 140 1002 Filter cover Fitment / change note → 1
18 1122 141 4000 Slide Fitment / change note → 1
19 1124 140 9500 Twist lock Fitment / change note → 1
20 9022 341 0980 Spline screw IS-M5x16 3
21 0000 120 1601 Air filter, fleece option 1
22 0000 141 0600 Prefilter option 1
23 0000 124 1000 Supporting plate option 1
24 1124 129 0900 NLA Gasket Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 0000 120 1655 Air filter option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 044 / 066 / 084

044 / 066 / 084: foam required with the shared HD filter

TI 46/1995 explicitly requires foam 1124 124 0804 on 044, 066 and 084, unlike 046.

Later reviewed guidance: 044 / 064 / 066 / 084: dry HD filter requires inner foam · 066 new filter system: winter mesh, dry HD and foam scope

  • The stated HD assembly 0000 120 1650 was introduced for 044 in TI 20/1995, 066 in TI 10/1995 and 084 in TI 18/1995. Those model names are explicit; no automatic expansion to 064, 088, MS 440, MS 660 or MS 880 is made.
  • The foam is necessary for 044, 066 and 084 but not required for 046; it remains in the shared package. Package contents alone do not determine installation on a specific model.
  • The separate model-specific instruction sheet remains unavailable in the reviewed sources. TI 10/1995 and TI 18/1995 exist in the retained queue but are not declared reviewed by this comparison.

Source: TI 46/1995, p. 10 — 5.1.3: other-model scope of shared HD filter.

Part numbers (2)
  • 0000 120 1650 — HD filter assemblyShared assembly · 044, 066, 084 with foam
  • 1124 124 0804 — Foam elementRequired on named models · 044, 066, 084; not the 046 requirement

Historical fitment · 044 / 064 / 066 / 084

044 / 064 / 066 / 084: dry HD filter requires inner foam

Dry fleece replacement, cleaning and model-specific foam rule.

Later reviewed guidance: 066 new filter system: winter mesh, dry HD and foam scope

  • Dry fleece HD filter 0000 120 1652 replaces oil-impregnated HD filter 0000 120 1650. The new filter carries the crossed-out OIL pictogram and does not need oil impregnation. This is not a blanket no-oil rule for the original filter or unrelated filter materials.
  • When cutting power noticeably drops, clean felt prefilter 0000 141 0300. After several prefilter cleanings, or if power remains low with a clean prefilter, remove the felt prefilter and clean the HD filter; carefully blow from the clean-air side if possible. On 044/064/066/084 also remove inner foam 0000 124 0800 for cleaning.
  • For stubborn dirt or caked fleece, wash filter parts in a clean non-flammable solution, such as warm soapy water. No air-pressure value, solvent recipe, drying duration or oiling step is supplied by this bulletin.
  • Fine trapped dirt may remain after cleaning and shorten cleaning intervals with extended use. Replace the filter when those intervals are no longer practical, or if thorough cleaning after long operation still leaves a noticeable cutting-power loss. No fixed service-hour limit or diagnosis excluding other causes is established.
  • Introduction is in progress, without a numeric cutoff. Original filter 0000 120 1650 was no longer supplied by the factory in this historical source, not a present stock assertion. An included instruction sheet is mentioned but is not reproduced or claimed reviewed here; the printed bulletin procedures above stand on their own.
  • Inner foam element 0000 124 0800 is included in the supplied HD filter and is required for 044, 064, 066 and 084. Refit the applicable inner foam after cleaning; the 046/088 removal rule does not apply to these models.
  • No later MS-model, every air-filter system or physical interchange claim is inferred from the shared part number.

Source: TI 43/1996, p. 1 · TI 43/1996, p. 2 — Both complete pages: dry fleece identification, cleaning, service life, installation and supply summary.

Part numbers (4)
  • 0000 120 1650 — Oil-impregnated HD air filterOriginal · 044 / 064 / 066 / 084
  • 0000 120 1652 — Dry fleece HD air filterReplacement · 044 / 064 / 066 / 084
  • 0000 141 0300 — Felt prefilterCleaning subject · 044 / 064 / 066 / 084
  • 0000 124 0800 — Inner foam elementRequired · 044 / 064 / 066 / 084

Historical fitment · 066

066 new filter system: winter mesh, dry HD and foam scope

The green wire-mesh filter serves normal/winter use; the black HD fleece filter with dry felt prefilter serves dry, very dusty sites. Foam is no longer required on the new-machine arrangement.

X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.

  • The cover mounting screw draws cover, filter and base together so peripheral sealing lips seal the intake. Efficiency, long service life and a perfect seal are source claims, not measured project performance.
  • The TI says clean when engine power noticeably falls. Tool-free selection is remove cover, change filter, refit cover. No solvent, oiling, cleaning interval or full maintenance procedure is invented.
  • Green wire mesh 0000 120 1651 is for normal conditions and winter; black HD fleece 0000 120 1652 for dry, very dusty sites. The replaceable dry felt prefilter 0000 141 0300 protects against coarse dirt. The drawing labels mesh on the left, fleece on the right, and TOP on the fleece prefilter.
  • The foam insert 0000 124 0800 is no longer required for new machines with the revised flange/baffle arrangement. This is not permission to remove foam from earlier 066 systems, 044, 064 or084. The earlier foam-required guidance remains valid within its stated configuration.
  • The HD filter and dry prefilter numbers remain unchanged. Table inclusion items 9 and 10 is retained even though foam item 10 has a dash in the new column; the prose scopes foam omission to new machines. An unchanged filter number alone does not identify the surrounding system.
  • Mesh, HD fleece and prefilter are already in inventory (remark 2). Original foam, filters 1122 120 1621 and 1122 120 1615, carburetor-box cover 1122 140 1900 and baffle 1122 121 7000 remain spares (remark 1); the original box cover includes twist lock item 12. HD conversion kit 1122 007 1031 is no longer supplied from the factory (remark 3). Dashes in the new column are not instructions to discard parts on old machines.

Source: TI 1/1998, p. 1 · TI 1/1998, p. 2 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Sections2,2.1,2.2,2.4; summary items7–10,21–24,42 and remarks.

Part numbers (10)
  • 0000 120 1651 — Winter wire-mesh filterNew version · 066; exact 1998 configuration and conditions apply
  • 0000 120 1652 — HD fleece air filterUnchanged number · 066; exact 1998 configuration and conditions apply
  • 0000 141 0300 — Dry felt prefilterUnchanged number · 066; exact 1998 configuration and conditions apply
  • 0000 124 0800 — Foam filter insertOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 120 1621 — Original air filterOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 120 1615 — Original air filterOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 140 1900 — Carburetor-box coverOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1124 140 9500 — Twist lockUnchanged number · 066; exact 1998 configuration and conditions apply
  • 1122 121 7000 — Original baffleOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 007 1031 — HD air-filter conversion kitOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply

Historical fitment · 066

066 filter base, flange and clip-on baffle

A redesigned flange and clip-on baffle accompany the new 066 intake system; the filter base changes from 1122 120 3411 to 1122 120 3402.

X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.

  • The flange drawing labels item 1. The baffle clips to the flange; the new flange, baffle and cover are said to improve intake efficiency, torque and performance. These are source claims, not project measurements.
  • Filter base item 14 and flange item 15 each list inclusion of unchanged stud item 16 M5x12x9. No torque or thread-repair procedure is supplied.
  • The baffle row lists includes items 18 and 19, but slotted nut 1124 141 8300 and collar screw 1122 122 6605 are original-column entries with new-column dashes. Retain this historical inclusion wording without making the clip-on design require the deleted attachment parts.
  • Original base, baffle, slotted nut and collar screw remain spares under remark 1. The new air guide is1122 141 6300. No blanket old-machine conversion permission follows from these rows; foam omission is limited to the new arrangement.

Source: TI 1/1998, p. 2 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Sections2.3–2.4 and summary items14–20.

Part numbers (9)
  • 1122 120 3411 — Filter baseOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 120 3402 — Filter baseNew version · 066; exact 1998 configuration and conditions apply
  • 1122 120 2200 — FlangeNew version · 066; exact 1998 configuration and conditions apply
  • 9121 319 0960 — Stud M5x12x9Unchanged number · 066; exact 1998 configuration and conditions apply
  • 1122 120 4101 — BaffleOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 121 6900 — BaffleNew version · 066; exact 1998 configuration and conditions apply
  • 1124 141 8300 — Slotted nutOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 122 6605 — Collar screwOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 141 6300 — Air guideNew version · 066; exact 1998 configuration and conditions apply

Historical fitment · 066

066 winter shutter: return to summer near +20°C

New cover 1122 140 1002 has a summer/winter shutter. Return it to summer when outside temperatures rise to about+20°C (68°F) to avoid running problems and overheating.

X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.

  • The new cover draws heated air from around the cylinder in winter position to reduce carburetor icing. Drawing 1 is summer and 2 is winter; the +20°C threshold is the printed approximate return-to-summer instruction, not a new cold-weather switch threshold.
  • Cover 1122 140 1001 changes to 1122 140 1002 and includes unchanged twist lock 1124 140 9500 plus new shutter 1122 141 4000. The original cover remains available as a spare (remark 1).
  • The winter-operation special-accessory cover plate 1122 084 8206 changes to 1122 084 8207; the drawing shows the plate on the fan housing. It is distinct from the filter-cover shutter and shroud rotary shutter.
  • Original preheating kit 1122 007 1027 includes twist lock item 12 and carburetor-box cover 1122 140 1901 (item 38); that cover includes plate item 39, cover 1122 141 2500 and blind rivet 9438 929 4040. The kit, box cover, small cover and rivet have dashes in the new column. All these original parts, including the original plate, remain spares under remark 1. No unprinted new complete preheating kit is inferred.

Source: TI 1/1998, p. 3 · TI 1/1998, p. 4 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Section2.5; section5 cover plate; summary items11–13,37–41.

Part numbers (10)
  • 1122 140 1001 — Filter coverOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 140 1002 — Filter coverNew version · 066; exact 1998 configuration and conditions apply
  • 1124 140 9500 — Twist lockUnchanged number · 066; exact 1998 configuration and conditions apply
  • 1122 141 4000 — Summer/winter shutterNew version · 066; exact 1998 configuration and conditions apply
  • 1122 084 8206 — Winter cover plateOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 084 8207 — Winter cover plateNew version · 066; exact 1998 configuration and conditions apply
  • 1122 007 1027 — Intake-air preheating kitOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 140 1901 — Preheating carburetor-box coverOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 141 2500 — CoverOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 9438 929 4040 — Blind rivetOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply

Conditional replacement · 066

066 new shroud requires its matching nameplate

Shroud 1122 080 1607 replaces 1122 080 1606 and must use new nameplate 1122 967 1505.

X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.

  • The shroud changes with the new intake system; the new nameplate must be used with the new shroud. This is a companion-part requirement, not evidence that the old nameplate fits.
  • The summary shroud includes items 26 and 27. Nameplate changes 1122 967 1504 to 1122 967 1505; rotary shutter 1125 080 8000 has a dash in the new column. That historical inclusion list is not an instruction to fit the old rotary shutter to the new shroud.
  • Original shroud, nameplate and rotary shutter remain spares under remark 1. No whole-system retrofit permission or new rotary-shutter part number is supplied.

Source: TI 1/1998, p. 3 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Section3 and summary items25–27.

Part numbers (5)
  • 1122 080 1606 — ShroudOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 080 1607 — ShroudNew version · 066; exact 1998 configuration and conditions apply
  • 1122 967 1504 — NameplateOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 967 1505 — NameplateNew version · 066; exact 1998 configuration and conditions apply
  • 1125 080 8000 — Rotary shutterOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply

Historical fitment · 066

066 wider housing and protected tank vent

Wider carburetor housing enlarges the filter compartment; tank volume increases about 5%. New vent 1122 350 5803 routes to a protected chamber in that housing.

Later reviewed guidance: 064 / 066: revised tank-vent package without the extra 044/046 ring

X 39 176 186 — TI01/1998 summary introduction of the described 066 modification; not a universal whole-saw interchange boundary.

  • Tank housing 1122 350 0816 changes to 1122 350 0817 and includes carburetor housing item 29, changed 1122 120 0102 to 1122 120 0104. The about 5% volume increase is a source-relative claim; no absolute tank capacity is supplied.
  • The new vent is routed to chamber 1 in the carburetor housing for dust/dirt protection. This routing is not evidence that the old housing accepts the new arrangement unchanged.
  • Original vent 1122 350 5850 remains a spare for machines up to X39 176185; the summary separately limits original-vent availability to the end of 1999 (remark 5). Neither statement is a current-stock claim, and the old-machine limit is one serial below the modification introduction X39 176186.
  • Original carburetor and tank housings remain available for older machines (prose; remark 1 in summary). The TI identifies 36/1997 as the introduction of the original vent and as last-TI bibliography; that retained bulletin is independently reviewed in the linked historical overlay (batch43), not closed by this reference alone. No missing procedure is required to interpret the locally printed change.

Source: TI 1/1998, p. 3 · TI 1/1998, p. 5 · TI 1/1998, p. 6 — Section4 including chamber drawing; summary items28–30 and remarks.

Part numbers (6)
  • 1122 350 0816 — Tank housingOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 350 0817 — Tank housingNew version · 066; exact 1998 configuration and conditions apply
  • 1122 120 0102 — Carburetor housingOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 120 0104 — Carburetor housingNew version · 066; exact 1998 configuration and conditions apply
  • 1122 350 5850 — Tank ventOriginal version / historical spare status · 066; exact 1998 configuration and conditions apply
  • 1122 350 5803 — Tank ventNew version · 066; exact 1998 configuration and conditions apply

Service note · 066

066: polyester felt prefilter replaces foam

1124 141 0301 replaces 1124 141 0300; old stock remains only until exhausted.

  • HD prefilter changes from foam 1124 141 0300 to needled felt with fabric plies, 100% POLYESTER, 1124 141 0301. Claimed benefits: longer cleaning intervals, better fit without stretching for improved seal toward filter, longer life and easier removal/installation. No numeric interval or cleaning method supplied.
  • Original prefilter remains factory-supplied ONLY UNTIL STOCKS EXHAUSTED. Introduction IN PROGRESS with no serial; do not use the cylinder-gasket cutoff. This is a prefilter change, not replacement of the whole HD element or evidence for other saws using the 1124 prefix. Diagram 1=old foam, 2=new felt. Footer April 29, 1994; previous TI19.94 reference is not whole-manual acceptance.
  • Historical TI 22/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 22/1994, p. 2 — 066: polyester felt prefilter replaces foam.

Part numbers (2)
  • 1124 141 0300 — Foam prefilterold; while stocks last · 066: polyester felt prefilter replaces foam
  • 1124 141 0301 — Needled polyester felt prefilternew · 066: polyester felt prefilter replaces foam

Conditional replacement · 064 / 066

064 / 066: modified HD filter needs the old gasket removed

From X 31 067 595: remove gasket 1124 129 0900 before the modified HD element; oil before first use, foam inside, felt TOP outward.

X 31 067 595 — Modified HD filter introduction on explicitly named 064/066 only; not a cylinder changeover or universal model-identification range.

  • The modified HD filter replaces the original metal version with an integrally molded rubber cover and TWO peripheral elastomer sealing lips. The TI states improved sealing between base and cover and filtration in fine dust; these are historical design claims, not measured filtration performance.
  • Before installing the new filter element, REMOVE original gasket 1124 129 0900 from the filter base. Its deletion from the new assembly is NOT universal spare unavailability: remark 4 explicitly retains it as a spare. This TI does not state a reverse-conversion procedure or extend the rule to later HD2 filters.
  • Illustration 132BB001: impregnate the filter element with STIHL HD filter oil BEFORE first installation.132BB002: fit the foam insert IN the HD filter.132BB003: fit felt prefilter 0000 141 0300 OVER the filter, with TOP pointing OUTWARD, then check seating. The felt is designed to sit firmly on the element. No oil quantity, oil order number or cleaning interval is given.
  • Follow the fitting and maintenance instructions supplied in the separate detailed HD-kit information sheet. That exact insert was not identified in the reviewed collection; this note retains the TI instructions but is NOT a complete substitute for the insert. No successor kit instructions are silently substituted.
  • The later 064/066 IPL sheets list HD2 filter 0000 140 4402 and optional air filter 0000 120 1655. These differ from complete HD filter 0000 120 1650 here; no equivalence, supersession or inheritance of the oiling procedure is inferred. The later 066 sheet still lists gasket 1124 129 0900; that does not override the modified-filter removal condition.
  • Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.

Source: TI 10/1995, p. 1 · TI 10/1995, p. 2 — Sections 1–2: complete two pages, illustrations 132BB001–003 and 137TI002, full summary and remarks.

Part numbers (4)
  • 1124 129 0900 — Original filter-base gasket / sealing ringremove for modified filter; remains spare · 064; 066; stated TI conditions
  • 0000 120 1650 — Complete HD filternew historical complete assembly · 064; 066; stated TI conditions
  • 0000 124 0800 — Foam filter insertinside HD filter · 064; 066; stated TI conditions
  • 0000 141 0300 — Felt prefilteroutside HD filter; TOP outward · 064; 066; stated TI conditions

Conditional replacement · 064 / 066

064 / 066: unchanged HD-kit number, revised contents

Kit 1122 007 1031 keeps its number; only its modified version is supplied. New bare elements are not separately available.

X 31 067 595 — Modified HD filter introduction on explicitly named 064/066 only; not a cylinder changeover or universal model-identification range.

  • Complete HD filter 0000 120 1650 (MOQ 1) includes keys 1–3: element, foam insert and felt prefilter. Original element 1124 120 1620 is replaced by a new element marked -*-; remark 1 says the NEW element is not available separately. No standalone new-element number or old-element availability is invented.
  • Keys 2/10: insert 1124 124 0804 becomes 0000 124 0800 (MOQ 10). Keys 3/11: prefilter 1124 141 0301 becomes 0000 141 0300 (MOQ 1). Originals are supplied ONLY until stocks are exhausted (remark 2); MOQ 10 is an ordering minimum, not ten installed inserts.
  • Key 4: HD air filter kit 1122 007 1031 keeps the SAME number in both columns; remark 3 means only its modified version is supplied. The table labels kit contents keys 5–12, while key 8 sealing ring 1124 129 0900 is explicitly deleted on the NEW side. The original key range does NOT reintroduce that ring into the modified kit.
  • Key 5 gasket 1122 129 1100 unchanged; key 6 filter base 1122 120 3410 becomes 1122 120 3411 (MOQ 1, old stock exhausted under remark 2), including key 7 stud 9121 319 0960, unchanged. Keys 9–11 repeat the element/insert/prefilter changes above; key 12 cover 1122 140 1000 unchanged. All other parts as before. Blank MOQ/remark cells do not imply zero or an unstated supply rule.
  • The table calls the unchanged stud M5 x 12 x 10; both later exact-model IPLs call the SAME 9121 319 0960 number M5x12x9. This dimensional-description conflict is preserved, not corrected by assumption. Later 064 gasket 1128 129 1100, covers 1122 140 1001(064)/1002(066), and 066 base 1122 120 3402 also differ; no equivalence or supersession follows from this TI.
  • Both introduction statements print X 31 067 595 for the HD change only. Last TI 51.94 is bibliographic. Footer: Waiblingen, March 06, 1995; ©1995 Andreas Stihl; D1/MTK-al, Technical Documentation. Issue 10.95 is not an October production date.
  • Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.

Source: TI 10/1995, p. 1 · TI 10/1995, p. 2 — Sections 1–2: complete two pages, illustrations 132BB001–003 and 137TI002, full summary and remarks.

Part numbers (13)
  • 0000 120 1650 — HD filter complete; includes 1–3new; MOQ 1 · 064; 066; stated TI conditions
  • 1124 120 1620 — Original HD filter element; keys 1/9new element not supplied separately · 064; 066; stated TI conditions
  • 1124 124 0804 — Original filter insert; keys 2/10available until stocks exhausted · 064; 066; stated TI conditions
  • 0000 124 0800 — New filter insert; keys 2/10MOQ 10 · 064; 066; stated TI conditions
  • 1124 141 0301 — Original felt prefilter; keys 3/11available until stocks exhausted · 064; 066; stated TI conditions
  • 0000 141 0300 — New felt prefilter; keys 3/11MOQ 1 · 064; 066; stated TI conditions
  • 1122 007 1031 — HD air filter kit; key 4unchanged number; modified version only · 064; 066; stated TI conditions
  • 1122 129 1100 — Gasket; key 5unchanged · 064; 066; stated TI conditions
  • 1122 120 3410 — Original filter base; key 6available until stocks exhausted · 064; 066; stated TI conditions
  • 1122 120 3411 — New filter base; key 6MOQ 1; includes stud 7 · 064; 066; stated TI conditions
  • 9121 319 0960 — Stud M5 x 12 x 10 as printed; key 7unchanged; later IPL says M5x12x9 · 064; 066; stated TI conditions
  • 1124 129 0900 — Sealing ring; key 8deleted from new assembly; remains spare · 064; 066; stated TI conditions
  • 1122 140 1000 — Filter cover; key 12unchanged · 064; 066; stated TI conditions

Service note · 066

066 shroud: raised valve opening and required cap without valve

Shroud 1605 becomes 1606; cylinder cover 1405 and shroud cap 7100 have different jobs. Conflicting supply wording retained.

X 32 231 689 — Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.

  • The new shroud has an opening surrounded by a RAISED AREA to protect the decompression valve from accidental contact (figure 137TI011). Separate cover 1122 084 1405 fits BETWEEN CYLINDER AND SHROUD to help prevent dust/dirt entry (figure 137TI010); it is not the shroud-opening cap or a cylinder pressure-test plug.
  • Shroud 1122 080 1605 changes to 1122 080 1606, table key 5, MOQ H 1, INCLUDING ITEM 6 cap 1122 084 7100 (cap MOQ H 1). Cover 1122 084 1405 is table key 4 with blank MOQ, not zero. No installation quantity or separate MOQ is inferred from that blank.
  • If the NEW SHROUD is used on a machine WITHOUT a decompression valve, its opening MUST BE SEALED with the provided cap 1122 084 7100 (figure 137TI009). The conditional shroud replacement does not itself authorize drilling or adding a valve to an earlier cylinder.
  • INTERNAL SOURCE CONFLICT: page 2 says ONLY THE NEW SHROUD is available as a replacement; page 3 assigns remark 1 to the old shroud, saying the ORIGINAL VERSION is factory-supplied while EXISTING STOCKS LAST. Preserve both statements rather than choosing a supply status or inventing an effective date.
  • Later 066 Q sheet key 1 lists shroud 1122 080 1607 and key 6 cap 1122 084 7101, not this TI’s 1606/7100. No undocumented supersession or free mixing of these versions is asserted. Later 066 B key 11 corroborates separate cylinder cover 1122 084 1405.
  • Historical TI guidance for model 066 only, subject to the stated version restrictions; shared series or part numbers do not extend this guidance to successor models. No present-day stock guarantee, physical interchange verification or model-identification serial interval is implied. No hardware operation was performed.

Source: TI 22/1995, p. 2 · TI 22/1995, p. 3 — Section 1 raised-opening and cover figures 137TI009–011, service note, shroud/cap/cover rows and remark 1.

Part numbers (4)
  • 1122 080 1605 — Original shroudtable key 5; stock-limited row conflicts with replacement prose · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.
  • 1122 080 1606 — New shroudtable key 5; includes item 6; MOQ 1 · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.
  • 1122 084 7100 — Shroud-opening capitem 6; required with new shroud on non-valve machine · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.
  • 1122 084 1405 — Cover between cylinder and shrouditem 4; dust/dirt barrier; MOQ not supplied · 066; Decompression-valve introduction on all 066 versions from this machine number; not a model-identification range or the undated HD-cover changeover.

Service note · 066

066 HD filter cover: forward-extended sides on all HD versions

Cover 1122 140 1000 becomes 1122 140 1001; this section gives no serial cutoff.

  • Section 2 replaces filter cover 1122 140 1000 with 1122 140 1001 on ALL HD FILTER VERSIONS of model 066, in connection with changes to Magnum models. Figure 137TI005 identifies old A and new B. The new sides extend FORWARD to close the gap between the carburetor box and filter cover.
  • This is broader HD-version wording than the earlier USA Magnum bulletin, but it does NOT say every non-HD 066 or successor model is covered. Section 2 says “in the future” and supplies NO SERIAL CUTOFF: X 32 231 689 belongs to section 1 decompression-valve changes and is not assigned to this cover.
  • No filter-cover MOQ or original-cover supply status is stated in section 2. Do not transfer remark 1 from the separate decompression-parts table or another region’s earlier bulletin to manufacture one.
  • Later 066 Q shroud/air-filter sheet key 17 lists filter cover 1122 140 1002, not TI-new 1001. This remains a later catalog difference, not an inferred 1001-to-1002 replacement chain or proof that every filter configuration fits.
  • The footer names TI10.95 as the last 066 TI and TI19.95 for USA and dates this issue March 30, 1995. These are bibliographic references, not a substitute serial date, missing installation dependency or claimed present compliance.
  • Historical TI guidance for model 066 only, subject to the stated version restrictions; shared series or part numbers do not extend this guidance to successor models. No present-day stock guarantee, physical interchange verification or model-identification serial interval is implied. No hardware operation was performed.

Source: TI 22/1995, p. 3 — Complete section 2, figure 137TI005 and footer.

Part numbers (2)
  • 1122 140 1000 — Original HD filter coverfigure A; old version · 066; All 066 HD-filter versions; section 2 gives no serial cutoff.
  • 1122 140 1001 — New HD filter coverfigure B; extended forward sides · 066; All 066 HD-filter versions; section 2 gives no serial cutoff.

Service note · 064 / 066

064 / 066: dry fleece HD filter at X 36 262 047

Do not oil the new fleece; preserve the earlier-system inner-foam requirement.

Later reviewed guidance: 066 new filter system: winter mesh, dry HD and foam scope

X 36 262 047 — Dry-fleece HD filter change for 064/066; not later 066 flange/foam deletion.

  • From X 36 262 047, dry-fleece HD filter 0000 120 1652 replaces original HD filter 0000 120 1650, which needs oil impregnation. The new fleece is designed to filter WITHOUT OIL and MUST NOT be impregnated with oil. This no-oil rule is material-specific, not permission to leave the original oil-treated filter dry.
  • The explicit See also TI43/1996 dependency is already reviewed. That source requires inner foam 0000 124 0800 on 064/066 and describes cleaning felt prefilter0000 141 0300 and HD filter. Reuse its exact configuration-specific guidance; dry fleece does not mean omit inner foam.
  • Later TI01/1998 omits foam only for the revised 066 flange/baffle arrangement from X 39 176 186, as documented in the linked later note. That later exception does not apply automatically at this earlier filter cutoff or to 064. Unchanged filter number does not identify the surrounding filter system.
  • Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.

Source: TI 8/1997, p. 2 — 064 / 066: dry fleece HD filter at X 36 262 047.

Referenced bulletin evidence: TI 43/1996, p. 1 · TI 43/1996, p. 2 — Both complete pages: dry fleece identification, cleaning, service life, installation and supply summary.

Part numbers (4)
  • 0000 120 1650 — Original oil-impregnated HD filterOriginal · 064 / 066; only the described configuration
  • 0000 120 1652 — New dry-fleece HD filterReplacement; do not oil · 064 / 066; only the described configuration
  • 0000 124 0800 — Inner foam for earlier 064/066 systemRequired companion from referenced TI43/1996 · 064 / 066; only the described configuration
  • 0000 141 0300 — Felt prefilterCleaning subject from referenced TI43/1996 · 064 / 066; only the described configuration

Service note · 066

066: plastic nameplate requires countersunk shroud holes

Original aluminium nameplates and two rivets remain replacements for older shrouds.

X 33 459 523 — Nameplate and prepared-shroud change only.

  • From X 33 459 523, riveted aluminium 066 nameplate1122 967 1501 changes to clip-in plastic1122 967 1504. New plate pushes into the carburetor-box cover and is retained by TWO LUGS; the shroud has two COUNTERSUNK holes.
  • Plastic plates CANNOT be fitted to the original shroud because its mounting holes are not countersunk. Original aluminium plates and round-head rivets remain available for older machines. This is not an instruction to countersink or modify the old shroud.
  • Each original nameplate listing includes TWO round-head rivets3x6,0000 974 1000. New rivet column is a dash because plastic retention uses lugs; no replacement rivet number or universal plate interchange is invented.
  • Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.

Source: TI 8/1997, p. 3 — 066: plastic nameplate requires countersunk shroud holes.

Part numbers (3)
  • 1122 967 1501 — 066 aluminium nameplateOriginal; retained for older machines · 066; only the described configuration
  • 1122 967 1504 — 066 plastic nameplateNew; requires countersunk shroud · 066; only the described configuration
  • 0000 974 1000 — Round-head rivet3x6, two per original plateOriginal retention; new column dash · 066; only the described configuration

Conditional replacement · 066

066: production setting symbol and symbol-free service cover

New production cover shows H3/4,L1/4; replacement 1122 140 1002 has no setting symbols.

  • Historical TI02/1998 for 066, series 1122 only; EPA restrictions and actual carburetor/version govern. No extension to 064, MS 660 or other successors. Introduction in progress; no serial cutoff supplied. No hardware operation was performed.
  • New production filter cover has the different setting symbol H = 3/4, L = 1/4. Replacement filter cover 1122 140 1002 will be supplied WITHOUT setting symbols.
  • Summary row 9 changes 1122 140 1001 → 1122 140 1002 and retains the original as a spare. A symbol-free replacement cover does not identify the installed carburetor or authorize using one setting for every version.

Source: TI 2/1998, p. 4 · TI 2/1998, p. 6 — Section 4 and summary row 9/remark 1.

Part numbers (2)
  • 1122 140 1001 — Original filter coverRetained original spare · 066; match the version and EPA restrictions in conditions
  • 1122 140 1002 — Replacement filter cover without setting symbolsNew · 066; match the version and EPA restrictions in conditions

Wrong number or missing part for the 066? Report a correction →