← 021/023/025 · MS 210/230/250

Stihl 1123 · Section C · 3 of 19 · 23 parts

Engine 025

Fits 025.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 42 mm (this machine only), Ø 42.5 mm (also listed for the MS 230, MS 230 C, MS 250, MS 250 C). Not interchangeable — measure your cylinder before ordering.

Position —

Go to table row → Where else is this used →
11011121213131416171823456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 1123 020 1206 Cylinder with piston Ø 42.5 mm 1
2 1123 020 1207 Cylinder with piston Ø 42.5 mm 1
3 1123 030 2011 Piston Ø 42.5 mm 1
4 1123 030 2002 Piston Ø 42 mm Fitment / change note → 1
5 1123 034 3006 Piston ring Ø 42.5x1.2 mm 2
6 1123 034 3003 Piston ring Ø 42x1.2 mm Fitment / change note → 2
7 4119 034 1500 Piston pin 10x6.5x28 1
8 9463 650 1000 Snap ring 10 2
9 0000 988 5211 Connector 1
10 9512 003 2250 Needle cage 10x13x12.5 Fitment / change note → 1
11 1123 030 0408 NLA Crankshaft 1
11 1123 030 0410 Crankshaft 1
12 9503 003 0340 Grooved ball bearing 6202 → replaced by 9503 003 0346 TI 6/2001 2
12 9503 003 0341 Grooved ball bearing 6202 2
13 9638 003 1581 Oil seal 15x25x5 Fitment / change note → 2
13 9639 003 1585 Oil seal 15x25x5 Fitment / change note → 2
13 9639 003 1586 Oil seal 15x25x5 2
14 9468 621 1520 Circlip 15x1 1
16 9075 478 4195 Pan head self-tapping screw IS-D5.3x41 4
17 1123 020 9400 Decompression valve Fitment / change note → 1
18 1110 400 7005 Spark plug Bosch WSR 6 F 1
18 0000 400 7000 Spark plug NGK BPMR7A 1
Not numbered on the diagram — assemblies, kits and options
— 0783 830 2000 Tube of sealant Dirko HT red not illustrated 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 021 / 023 / 025

021 / 023 / 025: easy-start version and market-specific valve omission

Manual primer, decompression valve and ElastoStart are the three described components, but some early easy-start saws omitted the valve.

  • The source introduces easy-start VERSIONS of 021, 023, 025, not a universal replacement of all variants. Manual fuel pump (drawing 1) primes the carburetor metering chamber; the source claims about 40% fewer pulls. This is a historical claim, not a measured guarantee or a claim of 40% less pulling force.
  • Decompression valve (2) is manually opened and automatically closes after firing; ElastoStart grip (3) cushions compression peaks. A NUMBER of easy-start saws up to X 30 950 036 were supplied WITHOUT a decompression valve in SOME markets. This is a qualified omission boundary, not a universal introduction cutoff or proof that every earlier saw lacks the valve.
  • Only the ElastoStart retrofit is expressly authorized across all three model families on page 5. Do not treat the parts roster or this overview as approval to retrofit the entire primer/decompression system.
  • Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.

Source: TI 10/1994, p. 1 — 021 / 023 / 025: easy-start version and market-specific valve omission.

No additional parts-table entry added.

Service note · 021 / 023 / 025

021 / 023 / 025 easy start: decompression valve operation and 14 Nm torque

Manually opened valve closes after ignition; service uses a long-reach 13 mm socket.

  • Complete valve 1123 020 9400 screws into cylinder. Body (1) contains axially moving tapered plunger (2); THREE spring-loaded balls (3), spaced 120 degrees, hold upper/lower positions. Push plunger DOWN to lower detent before starting: taper lifts from body, opening escape bore. During cranking some cylinder gas escapes and remaining pressure stays below closing threshold.
  • Only after mixture ignites and engine runs does cylinder pressure exceed valve closing pressure, forcing plunger UP so taper closes bore. No numeric closing-pressure threshold is supplied. Drawings show mechanism, not internal service-part availability.
  • Removal/installation uses standard commercial LONG-REACH 13 mm socket to ISO 2725 or DIN 3124. Tighten to 14 Nm (10.3 lbf.ft). This is valve torque, not cylinder or spark-plug torque. Some easy-start machines up to X 30 950 036 omitted the valve in some markets; do not assume presence from model alone.
  • Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.

Source: TI 10/1994, p. 1 · TI 10/1994, p. 3 · TI 10/1994, p. 5 · TI 10/1994, p. 6 — 021 / 023 / 025 easy start: decompression valve operation and 14 Nm torque.

Part numbers (1)
  • 1123 020 9400 — Complete decompression valve, itemAincluded in listed easy-start cylinder assemblies · 021 / 023 / 025 easy start: decompression valve operation and 14 Nm torque

Service note · 025

025: model-specific easy-start cylinder and piston

1123 020 1217 is the listed 025 easy-start assembly including decompression valveA.

  • Page 6 assigns cylinder with piston 1123 020 1217 specifically to 025 EASY START, including decompression valve 1123 020 9400 (A). The separate 021/023/025 cylinder numbers are not a cross-model interchange claim. No bore, piston dimension, original cylinder replacement number or full easy-start conversion procedure is supplied.
  • Page 1 qualifies valve presence: a number of easy-start saws up to X 30 950 036 lacked a valve in some markets. Preserve that statement alongside the spare-assembly inclusion; do not silently infer every originally supplied cylinder had a valve.
  • Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.

Source: TI 10/1994, p. 1 · TI 10/1994, p. 6 — 025: model-specific easy-start cylinder and piston.

Part numbers (2)
  • 1123 020 1217 — Cylinder with piston, 025 easy startmodel-specific assembly; includesA · 025: model-specific easy-start cylinder and piston
  • 1123 020 9400 — Decompression valve, itemAincluded · 025: model-specific easy-start cylinder and piston

Service note · 025

025: revised piston ring, unchanged 42 mm piston number

New ring 1123 034 3003 replaces 1121 034 3001 only in the stated 025 application.

  • Section 6 is specifically Piston ring (025). Ring 1121 034 3001 changes to 1123 034 3003; 42 mm piston 1123 030 2002 keeps its number and includes ring item 1. Unmodified piston version remains factory-supplied until existing stocks are exhausted.
  • Original ring remains available for OTHER models, which are not named here. Do not extend the 025 ring replacement to 021 or 023 just because they share the bulletin cover. Introduction in progress, no serial or physical ring dimensions beyond the piston D42 label.
  • Historical TI 13/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 13/1994, p. 4 — 025: revised piston ring, unchanged 42 mm piston number.

Part numbers (3)
  • 1123 030 2002 — 42 mm piston including ring item 1unchanged number; old version while stocks last · 025: revised piston ring, unchanged 42 mm piston number
  • 1121 034 3001 — Original 025 piston ringretained for other models · 025: revised piston ring, unchanged 42 mm piston number
  • 1123 034 3003 — Revised 025 piston ring, item 1new · 025: revised piston ring, unchanged 42 mm piston number

Service note · 023 / 025

023 / 025: loose piston-pin needle cage remains required

TI13 distinguishes 023/025 spare cage from the revised integral-cage 021 rod.

  • Replacement needle cage 9512 003 2250 is explicitly still required for models 023 and 025 because the revised 021 connecting rod incorporates a press-fitted cage. Do not bind 021 rod 1123 030 1202 as a 023/025 replacement; neither a new 023/025 rod number nor a separate cutoff is supplied.
  • The last-TI pointer 04.93 and publication date March 7, 1994 are source context, not an assertion that the earlier TI or a full service manual has been reviewed.
  • Historical TI 13/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 13/1994, p. 4 — 023 / 025: loose piston-pin needle cage remains required.

Part numbers (1)
  • 9512 003 2250 — Replacement piston-pin needle cagerequired for 023 and 025 in stated revision context · 023 / 025: loose piston-pin needle cage remains required

Service note · 021 / 023 / 025

021 / 023 / 025 leakage test: replace decompression valve with plug

Plug 1122 025 2200 required before testing; 13-mm deep socket for valve.

  • On the named saws EQUIPPED WITH A DECOMPRESSION VALVE, plug 1122 025 2200 MUST be installed IN PLACE OF THE VALVE BEFORE THE LEAKAGE TEST. This is a test preparation step, not evidence of permanent valve deletion or an instruction to test through the valve.
  • Decompression valve removal and installation use a standard commercial 13-mm DEEP WELL SOCKET. Immediately following valve-installation wording gives tightening torque 14 Nm (10 ft lbs.). Preserve that valve context; no separate plug torque is explicitly identified.
  • The TI refers to the service manual for the leakage test; it does not specify test pressure, vacuum, duration, leakage limit or the complete blocking procedure. None is inferred from this note. Shared engine sheets show decompression valves but do not prove every model variant has one.
  • Later shared engine sheet A key 16 lists the plug. Binding to engine sheets A/B/C provides navigation for 021/023/025; it does not extend this valve instruction to an unequipped version.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 29/1995, p. 4 — Section 5.1 leakage-test service note.

Part numbers (1)
  • 1122 025 2200 — Plugrequired in place of decompression valve before leakage test · 021 / 023 / 025; Section 5.1 leakage-test service note

Service note · 021 / 023 / 025

021 / 023 / 025 locking strip: close decompression valve first

Open valve may bend when piston presses against the locking strip.

  • On saws EQUIPPED WITH A DECOMPRESSION VALVE, the valve MUST BE CLOSED BEFORE locking strip 0000 893 5903 is inserted into the SPARK PLUG HOLE. If left open, the valve may be bent by the piston pressing against the strip. Closed-valve prerequisite is distinct from removing the valve and fitting a plug for a leakage test.
  • No piston position, turning direction, applied torque or permission to run the engine with a locking strip is supplied. This precaution is not a complete disassembly procedure or proof that the strip is suitable for every other saw model.
  • Footer: August 7, 1995, D1/MTK-st; prior TI 17/1995 is bibliographic. It is not a serial cutoff or production date for these in-progress changes. No hardware procedure has been performed.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 29/1995, p. 4 — Section 5.2 locking-strip precaution and footer.

Part numbers (1)
  • 0000 893 5903 — Locking stripinsert only after closing decompression valve · 021 / 023 / 025; Section 5.2 locking-strip precaution and footer

Service note · 021 / 023 / 025

021/023/025: oil seal depends on engine-pan separation

Assembled cylinder and pan permit press-fitting only 9638 003 1581.

  • Section 3: IF THE ENGINE PAN IS SEPARATED from the cylinder during repair, production oil seal 9639 003 1585 WITH RIGID HOUSING MAY be installed. This is conditional permission, not an instruction that it must replace every 1581 seal.
  • IF CYLINDER AND ENGINE PAN ARE STILL ASSEMBLED, ONLY oil seal 9638 003 1581 (the replacement supplied up to then) MAY BE PRESS-FITTED. Equal dimensions or coexistence in an IPL do not make 1585 a press-in replacement in this assembled condition.
  • The summary table prints original --- and new 9638 003 1581 even though the prose calls 1581 the previously supplied replacement. Preserve both statements: the table does not establish a 1581→1585 supersession or cancel the assembly-state restriction.
  • The detailed technical reasons are explicitly deferred to TI39/1990. That source is unavailable in the retained 690-TI corpus and bounded service-documentation PDF filename inventory (766 PDFs); no mechanical rationale, insertion tool, depth, sealant or torque is invented.
  • Later engine sheets A (021), B (023/023 L) and C (025) list BOTH seal numbers as 15x25x5, quantity 2, under their shared seal key. Those are IPL dimensions/quantities, not additional specifications printed in this TI and not unrestricted interchange.
  • Historical TI24/1996 guidance only. No serial cutoff is stated; introduction is in progress, not a verified calendar date. Shared IPL sheets do not extend applicability to other variants or MS successor models. Supply statements are historical, not present stock guarantees. No hardware operation was performed.

Source: TI 24/1996, p. 1 · TI 24/1996, p. 3 — 021/023/025: oil seal depends on engine-pan separation.

Part numbers (2)
  • 9639 003 1585 — Oil seal with rigid housingPermitted when pan is separated · 021/023/025; installation depends on pan/cylinder assembly state
  • 9638 003 1581 — Oil seal, existing replacementOnly press-fit seal while pan/cylinder remain assembled · 021/023/025; installation depends on pan/cylinder assembly state

Service note · 023 / 025

023 / 025: replacement-crankshaft needle cage is installed with the pin

This service distinction is not the 021 press-fitted needle sleeve.

  • Page 1 explicitly distinguishes replacement crankshafts for models 023 and 025: the needle cage is installed along with the piston pin. This contrasts with the new 021 crankshaft small-end needle sleeve press-fitted into the rod. No 023/025 replacement-crankshaft, needle-cage or piston-pin part number is supplied in this statement; none is invented.
  • The separate service note on page 1 and remark 2 on page 2 require original piston 1123 030 2001 to remain in model 023 saws. This is NOT a piston requirement for 025 and does not transfer the 021 cutoff X 34 944 403 to either model. The shared engine sheet mentions 023 L, but this statement only explicitly names 023.
  • Historical TI13/1997 evidence for the exact named model/configuration only. Shared IPL labels are discovery links, not applicability to every model or later carburetor suffix on that sheet. Availability statements describe 1997, not current stock. No successor-model scope, universal retrofit or tested interchange is inferred. No hardware operation was performed.

Source: TI 13/1997, p. 1 · TI 13/1997, p. 2 — 023 / 025: replacement-crankshaft needle cage is installed with the pin.

Part numbers (1)
  • 1123 030 2001 — Original piston still required on 023023 service exception only; NOT a 025 piston specification · 023 only; the 023/025 needle-cage statement does not assign this piston to 025.

Wrong number or missing part for the 025? Report a correction →