← 021/023/025 · MS 210/230/250

Stihl 1123 · Section E · 5 of 19 · 17 parts

Quick chain tensioner

Fits 021, 023, 025.

Parts diagrams →

Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151623456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (17)

PosPart numberDescriptionQty
1 1123 640 1700 NLA Chain sprocket cover Fitment / change note → 1
2 1123 648 3800 NLA Cover plate Fitment / change note → 1
3 1123 648 2202 NLA Adjusting wheel 1
4 9104 003 8600 NLA Self-tapping screw P3x10 Fitment / change note → 1
5 1121 660 1000 Wing nut 1
6 not sold separately Torsion spring not available as a separate item 1
7 not sold separately Cap not available as a separate item 1
8 not sold separately Handle not available as a separate item 1
9 not sold separately Cylindrical pin 3m6x26 not available as a separate item 2
10 1123 664 2402 NLA Collar screw Fitment / change note → 1
11 1123 660 3001 NLA Tensioning gear 1
12 9041 319 0600 NLA Pan head screw M4x5 Fitment / change note → 1
13 1123 664 0501 Bumper spike Fitment / change note → 1
14 9075 478 4115 Pan head self-tapping screw IS-D5x16 Fitment / change note → 2
15 1123 021 2800 Insert Fitment / change note → 1
16 0812 370 1000 Screwdriver T27x120x70 1
Not numbered on the diagram — assemblies, kits and options
— 1123 007 1008 NLA Quick tensioner parts Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 021 / 023 / 025

021 / 023 / 025: quick tensioner operation and anti-rotation lock

Hand-tightened wingnut locks by folding its toothed wing closed.

  • Conventional tensioning first adjusts the chain, then clamps the bar with mounting nuts; screwdriver/combination wrench are needed. In quick-tensioner drawing135TI001, adjusting wheel1 rotates tensioning gear2, which converts rotation into forward/backward guide-bar travel to tension/slacken the chain.
  • Wingnut3 engages the collar stud and clamps the guide bar; tighten ONLY BY HAND. It can turn only when hinged wing4 is folded OUT. With the wing closed, its teeth engage the chain-sprocket-cover teeth to prevent loosening. Do not substitute a wrench torque or operate it with the wing forced closed.
  • Drawing135TI001 also marks a feature5 without naming it in the operation text. It is not automatically page4 table key5 (wingnut): figure numbering and spare-parts numbering are different contexts. No clockwise/counterclockwise adjustment direction, numeric chain slack or complete use procedure is specified here.
  • Historical TI 42/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 42/1994, p. 2 · TI 42/1994, p. 3 — quick tensioner operation and anti-rotation lock.

No additional parts-table entry added.

Service note · 021 / 023 / 025

021 / 023 / 025: quick tensioner stud roles and cover

Only the front collar stud clamps the bar; the short rear screw prevents rotation.

  • In drawing135TI002, FRONT collar stud1 alone clamps the cutting attachment on quick-tensioner machines. REAR collar screw2 prevents guide-bar rotation; only its 5 mm (0.2 in) head projects from the engine housing. This is projection, not a tightening torque or the full screw length.
  • Adjusting wheel, wingnut and anti-rotation teeth are integrated in the chain sprocket cover. The cover projects forward farther than the conventional arrangement, requiring the longer spiked bumper. Do not use a conventional two-nut clamping procedure for the illustrated quick tensioner.
  • The spiked-bumper comparison135TI011 labels original1123 664 0500 on the LEFT and longer1123 664 0501 for quick tensioner on the RIGHT. No numeric spike length or fabrication dimensions are specified.
  • Historical TI 42/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 42/1994, p. 3 — quick tensioner stud roles and cover.

Part numbers (2)
  • 1123 664 0500 — Original spiked bumperComparison left; inadequate reach after retrofit · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 664 0501 — Longer quick-tensioner spiked bumperComparison right; required with retrofit · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply

Service note · 021 / 023 / 025

021 / 023 / 025: quick tensioner retrofit requires longer bumper

Kit1123 007 1008 may retrofit the listed models only with mandatory bumper1123 664 0501.

  • The source permits quick-tensioner retrofit to ALL existing021,023 and025 using mounting kit1123 007 1008. It does not extend this historical authorization automatically to MS210/230/250, unnamed variants or arbitrary tensioner parts.
  • After retrofit, the integrally molded bumper on021/023 and original separate bumper1123 664 0500 on025 no longer reach the wood sufficiently. For SAFETY, longer spiked bumper1123 664 0501 supplied in the kit MUST be fitted; it is not an optional accessory. Its longer spikes restore saw support in the cut.
  • Detailed FITTING AND USE instructions are supplied with the kit. They are not reproduced in this four-page TI; a scoped named-file search did not establish the exact kit insert. Two local1123-family manuals are not established as that insert, and one produces PDF text-parser errors. The kit-document dependency remains unverified, not proof that the named source is absent globally. Do not present these TI notes as the complete kit installation/use procedure.
  • Historical TI 42/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 42/1994, p. 2 · TI 42/1994, p. 3 · TI 42/1994, p. 4 — quick tensioner retrofit requires longer bumper.

Part numbers (3)
  • 1123 007 1008 — Quick chain tensioner mounting kitRetrofit kit; bumper mandatory · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 664 0500 — Original025 spiked bumperInsufficient reach with quick-tensioner cover · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 664 0501 — Longer spiked bumperMandatory safety component · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply

Service note · 021 / 023 / 025

021 / 023 / 025: quick tensioner cover parts and ambiguous order quantity

The adjusting-wheel MOQ cell visibly reads101/overprinted10-plus1; do not silently normalize it.

  • Complete mounting kit1123 007 1008 contains table keys1–11,MOQ1. Chain sprocket cover1123 640 1700 (key1,MOQ1) includes keys2–4: adjusting wheel1123 648 2200; P3x10 screw9104 003 8600 (MOQ10); cover plate1123 648 3800 (MOQ1). The wingnut is a separate kit row, not within the stated cover keys2–4.
  • The adjusting-wheel MOQ cell extracts as “101”; the original high-resolution PDF also shows a trailing/overprinted1 beside10. Preserve this source ambiguity: no confirmed numeric order quantity is admitted for that row, and neither101 nor10 is an installation quantity. No matching footnote explains the extra1.
  • Wingnut1123 660 1000 (key5) MOQ1. Collar screw1123 664 2402 (key6) MOQ10. These table key numbers must not be substituted into page2 operating-diagram numbering. MOQ is minimum order quantity, not a count fitted to one saw.
  • Historical TI 42/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 42/1994, p. 4 — quick tensioner cover parts and ambiguous order quantity.

Part numbers (7)
  • 1123 007 1008 — Complete quick tensioner mounting kit; keys1–11MOQ1 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 640 1700 — Chain sprocket cover; key1,includes2–4MOQ1 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 648 2200 — Adjusting wheel; key2MOQ cell101/overprinted10-plus1 unresolved · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 9104 003 8600 — P3x10 screw; key3MOQ10 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 648 3800 — Cover plate; key4MOQ1 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 660 1000 — Wingnut; key5MOQ1 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 664 2402 — Collar screw; key6MOQ10 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply

Service note · 021 / 023 / 025

021 / 023 / 025: quick tensioner gear, bumper and fitting tools

Two bumper screws is an explicit quantity; blank MOQ cells remain unspecified.

  • Tensioning gear1123 660 3000 (key7,MOQ1) includes M4x5 screw9041 319 0600 (key8,MOQ10). Spiked bumper1123 664 0501 (key9) MOQ5. DG5x16 screw9075 478 4115 (key10) has explicit2x installation quantity. Screwdriver0812 370 1145 is key11.
  • Both DG5x16 screw and screwdriver carry remark1: already supplied for other models. Their MOQ cells are BLANK, not zero and not copied from neighboring rows. The table supplies neither screw tightening torque nor screwdriver-tip specification. Two screws is a part quantity, distinct from MOQ.
  • The printed bulletin identifier is42.94 but the footer is Waiblingen,February1,1995 and copyright1995,Andreas Stihl,D1/MTK-st. Keep the retained1994-42 identifier separate from the printed publication date; no serial cutoff is inferred. Prior-bulletin reference38.94 is provenance, not permission to substitute parts from every topic in that TI.
  • Historical TI 42/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 42/1994, p. 4 — quick tensioner gear, bumper and fitting tools.

Part numbers (5)
  • 1123 660 3000 — Tensioning gear; key7,includes8MOQ1 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 9041 319 0600 — M4x5 screw; key8MOQ10 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 1123 664 0501 — Longer spiked bumper; key9MOQ5 · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 9075 478 4115 — DG5x16 screw; key10,2xMOQ unspecified;already supplied for other models · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply
  • 0812 370 1145 — Screwdriver; key11MOQ unspecified;already supplied for other models · 021 / 023 / 025 with the specified quick-tensioner configuration; historical kit restrictions apply

Service note · 021 / 023 / 025

021 / 023 / 025 quick tensioner: replace rear housing stud

Replacement housing needs collar screw 2402; slow stud removal protects threads.

  • Replacement standard housing 1123 020 3005 and easy-start housing 1123 020 3006 arrive with TWO COLLAR STUDS OF THE SAME LENGTH. For a saw WITH QUICK CHAIN TENSIONER, the REAR stud (1) MUST be replaced by collar screw 1123 664 2402 (2). The screw may be transferred from the faulty housing or ordered separately. This is conditional conversion of the replacement housing, not a change to every standard-tensioner saw.
  • Use M8 stud puller 5910 893 0501 to unscrew the rear stud SLOWLY from the replacement housing: removing it too quickly may damage the housing thread. Remove the collar screw from the faulty housing when reusing it. Apply a LITTLE OIL to the new or original screw thread; oil grade and numerical extraction speed are not specified.
  • Position screw in replacement-housing hole, rotate COUNTERCLOCKWISE UNTIL IT DROPS DOWN SLIGHTLY, then screw home CLOCKWISE to APPROXIMATELY 8 Nm (6.0 lbf.ft). Its collar MUST BUTT AGAINST THE ENGINE HOUSING like the original stud. Do not replace this thread-engagement step with a cutting or drilling operation.
  • Install the engine housing as described in the service manual and fit the REQUIRED longer-spike bumper 1123 664 0501; its separate mounting torque is 3.7 Nm (2.8 lbf.ft), not the collar screw torque. TI 42/1994 is cited and retained locally; this note does not reproduce the full engine-housing replacement procedure.
  • Later quick-tensioner sheet E key 10 lists 2402. Later housing sheet D lists 3003/3004 instead of the TI 3005/3006; that difference is not a proven supersession. Figures identify the rear location and seated collar, not a numerical stud-length specification.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 29/1995, p. 3 — Section 3.2 collar-stud conversion and figures 135TI024/025 SC.

Part numbers (5)
  • 1123 020 3005 — Standard replacement engine housingtwo equal-length studs supplied · 021 / 023 / 025; Section 3.2 collar-stud conversion and figures 135TI024/025 SC
  • 1123 020 3006 — Easy-start replacement engine housingtwo equal-length studs supplied · 021 / 023 / 025; Section 3.2 collar-stud conversion and figures 135TI024/025 SC
  • 1123 664 2402 — Rear collar screwrequired for quick tensioner · 021 / 023 / 025; Section 3.2 collar-stud conversion and figures 135TI024/025 SC
  • 5910 893 0501 — M8 stud pullerslow removal of rear stud · 021 / 023 / 025; Section 3.2 collar-stud conversion and figures 135TI024/025 SC
  • 1123 664 0501 — Longer-spike bumpermandatory companion requirement · 021 / 023 / 025; Section 3.2 collar-stud conversion and figures 135TI024/025 SC

Service note · 021 / 023 / 025

021 / 023 / 025 quick tensioner requires longer-spike bumper

Bumper 0501 is mandatory; 0500 is the illustrated comparison, not an alternative.

  • For SAFETY REASONS, spiked bumper 1123 664 0501 MUST be fitted to the engine housing of machines WITH A QUICK CHAIN TENSIONER. Longer spikes help provide better contact with the wood during cutting; this is not an optional accessory recommendation.
  • When replacing the engine housing, remove 0501 from the faulty housing and mount it on the replacement; tightening torque 3.7 Nm (2.8 lbf.ft). The earlier collar-screw step uses approximately 8 Nm; do not transfer that torque to the bumper.
  • Figure LEFT is original comparison bumper 1123 664 0500; RIGHT is 1123 664 0501 for the quick tensioner. No dimensions or modification procedure are supplied; do not infer that 0500 can be reshaped to meet the requirement.
  • Later quick-tensioner sheet E key 13 lists 0501 and chain-brake sheet H key 19 lists 0500. Co-listing on shared-model sheets does not make them interchangeable for the stated quick-tensioner application.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 29/1995, p. 3 — Section 3.2 spiked-bumper service step, safety statement and figure 135TI011.

Part numbers (2)
  • 1123 664 0500 — Comparison spiked bumperillustration left; not the required quick-tensioner version · 021 / 023 / 025; Section 3.2 spiked-bumper service step, safety statement and figure 135TI011
  • 1123 664 0501 — Longer-spike bumperrequired for quick chain tensioner · 021 / 023 / 025; Section 3.2 spiked-bumper service step, safety statement and figure 135TI011

Historical fitment · 021 / 023 / 025

021/023/025: quick-tensioner stiffener retrofit

Added stiffener reinforces the bar mounting flange; the kit number stays unchanged.

  • Section 1: stiffener 1123 021 2800 is installed IN THE ENGINE HOUSING to increase rigidity at the bar mounting flange. Drawing 135TI030 shows its location; this is not a chain-cover washer or a replacement bar stud.
  • The stiffener CAN BE BACKFITTED to machines WITH A QUICK CHAIN TENSIONER brought in for repair or servicing. This does not establish fitment to standard-tensioner machines or a complete standard-to-quick conversion procedure.
  • Quick chain tensioner kit 1123 007 1008 retains the SAME original/new number and now includes item 2, stiffener 1123 021 2800. Only the modified kit is available from the factory under remark 1. An older kit bearing the same number is not proof that the stiffener is present.
  • Later SCS 01-2012 sheet E lists the stiffener as Insert at key 15 and marks kit 1008 no longer available. These later catalog labels do not negate the 1996 inclusion/backfit statement or promise current availability.
  • Historical TI24/1996 guidance only. No serial cutoff is stated; introduction is in progress, not a verified calendar date. Shared IPL sheets do not extend applicability to other variants or MS successor models. Supply statements are historical, not present stock guarantees. No hardware operation was performed.

Source: TI 24/1996, p. 1 — 021/023/025: quick-tensioner stiffener retrofit.

Part numbers (2)
  • 1123 007 1008 — Quick chain tensioner kit, including stiffenerSame-number revised kit · 021/023/025 with quick chain tensioner
  • 1123 021 2800 — Stiffener for bar mounting flangeNew; conditional retrofit · 021/023/025 with quick chain tensioner

Wrong number or missing part for the 021, 023, 025? Report a correction →