Stihl 1123 · Section P · 15 of 19 · 37 parts
Carburetor WT-215, WT-286
Fits 021, 023, 025.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1115 121 5401 | Valve jet | 1 |
| 2 | 4117 122 9402 | Plug | 1 |
| 3 | 4116 121 5100 | Inlet needle | 1 |
| 4 | 1120 122 3001 | Spring | 1 |
| 5 | 1113 121 5000 | Inlet control lever | 1 |
| 6 | 1113 121 9200 | Spindle | 1 |
| 7 | 1114 122 7400 | Round head screw | 1 |
| 8 | 1120 129 0900 | Gasket | 1 |
| 9 | 1113 121 4705 | Metering diaphragm | 1 |
| 10 | 1113 121 0800 | End cover | 1 |
| 11 | 1106 122 7400 | Round head screw | 4 |
| 12 | 1114 121 7800 | Strainer | 1 |
| 13 | 1121 121 4801 | Pump diaphragm | 1 |
| 14 | 1120 129 0905 | Gasket | 1 |
| 15 | 1123 121 0802 | End cover | 1 |
| 16 | 1114 122 7100 | Screw | 1 |
| 17 | 4117 122 3006 | Spring | 1 |
| 18 | 1123 122 6201 | Idle speed adjustment screw | 1 |
| 19 | 1113 122 3205 | Torsion spring | 1 |
| 20 | 1123 120 7101 | Throttle shaft with lever | 1 |
| 21 | 1123 121 3301 | Throttle shutter | 1 |
| 22 | 1115 122 7400 | Round head screw | 1 |
| 23 | 1117 122 9000 | E-clip | 1 |
| 24 | 1123 122 6801 | Low speed adjustment screw | 1 |
| 25 | 1115 122 3002 | Spring | 1 |
| 26 | 1118 122 6700 | High speed adjustment screw | 1 |
| 27 | 4117 122 3007 | Spring | 1 |
| 28 | 1123 122 3201 | Torsion spring | 1 |
| 29 | 1123 120 7201 | Choke shaft with lever | 1 |
| 30 | 1110 122 7400 | Round head screw | 1 |
| 31 | 1123 122 9000 | E-clip | 1 |
| 32 | 1123 122 3900 | Elbow connector | 1 |
| 33 | 1123 121 2901 | Choke shutter Fitment / change note → | 1 |
| 34 | 1123 121 2902 NLA | Choke shutter Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1123 120 0605 | Carburetor WT-215 Fitment / change note → | 1 |
| — | 1123 120 0615 NLA | Carburetor WT-286A Fitment / change note → | 1 |
| — | 1123 007 1061 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 021 / 023 / 025
021 / 023 / 025 easy start: primer flow, hose lengths and sealing
68 mm intake goes on the short rearward nipple; 190 mm return goes on the long central nipple.
- Manual primer 4130 350 6200 is double-acting and mounted in handle housing. PRESSING the bulb closes the intake and opens return, forcing fuel already in the bulb to tank. RELEASING closes return and opens intake; bulb spring action draws fuel from tank pickup/suction hose through carburetor fuel pump, metering system and primer intake hose. It primes through the carburetor, not directly into the cylinder.
- Carburetor nipple is on the metering side; non-return valve between metering chamber and jet system prevents the primer draining the jet system. Return enters tank through a grommet next to the tank vent. Air initially appears in the bulb and is progressively returned to tank on presses. Depending on trapped air after dry tank/storage, source says 3–8 presses; proper priming leaves an air bubble about the size of a PEA, not necessarily zero bubbles.
- Remove by disconnecting both hoses, squeezing two spring tabs and pulling pump from seat. Faulty pump CANNOT be repaired and must be replaced. Install with SHORT intake nipple pointing toward REAR HANDLE; push fully home until tabs snap into place.
- Fit 68 mm intake hose 1123 358 7600 on SHORT nipple; fit 190 mm return hose 1123 358 7601 on LONG nipple near center. Insert helical spring 0000 997 0229 into intake hose to keep its diameter open/prevent kinking, then connect intake to carburetor nipple. Route return through carburetor box and retainers into tank grommet 0000 989 0816. Grommet MUST be fitted for a good seal. Page 5 diagram hose keys 2/3 differ from page 6 roster keys 9/11; keep contexts separate.
- Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.
Source: TI 10/1994, p. 2 · TI 10/1994, p. 5 · TI 10/1994, p. 6 — 021 / 023 / 025 easy start: primer flow, hose lengths and sealing.
Part numbers (5)
- 4130 350 6200 — Manual fuel primer, page 6 item 8new easy-start part; replace if faulty · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
- 1123 358 7600 — 68 mm intake hose, item 9short rearward nipple · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
- 0000 997 0229 — Intake anti-kink spring, item 10required in intake hose · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
- 1123 358 7601 — 190 mm return hose, item 11long central nipple · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
- 0000 989 0816 — Tank return-hose grommet, item 5required sealing part · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
Service note · 021 / 023 / 025
021 / 023 / 025: WT 286 choke bore differs from standard WT 215
Easy-start WT 286 1123 120 0615 uses 3.8 mm choke bore, not standard 2.1 mm.
- WT 286 carburetor 1123 120 0615 (page 6 item 12) includes choke shutter 1123 121 2902 (13), bore 3.8 mm (0.15 inch). Standard WT 2151123 120 0605 uses choke shutter 1123 121 2901, bore 2.1 mm (0.08 inch). Keep the two shutter numbers and bore sizes distinct.
- Section 2.2 says spare parts are practically identical except choke shutter; page 6 remark 2 says OTHER parts identical to WT 2151123 120 0605. This bounded component-spare statement is not unrestricted complete-carburetor interchange: section 1.1 describes the primer nipple and non-return valve on the new carburetor.
- The non-return valve between metering chamber and jet system is substantially maintenance-free and does not need replacement according to the source. No separate number, repair procedure, jet setting or later WT 286A substitution is supplied.
- Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.
Source: TI 10/1994, p. 2 · TI 10/1994, p. 5 · TI 10/1994, p. 6 — 021 / 023 / 025: WT286 choke bore differs from standard WT215.
Part numbers (4)
- 1123 120 0615 — WT 286 including choke shutter, item 12easy-start carburetor · 021 / 023 / 025: WT 286 choke bore differs from standard WT 215
- 1123 120 0605 — WT 215standard comparison carburetor · 021 / 023 / 025: WT 286 choke bore differs from standard WT 215
- 1123 121 2902 — Choke shutter, item 13; 3.8 mm boreeasy-start · 021 / 023 / 025: WT 286 choke bore differs from standard WT 215
- 1123 121 2901 — Choke shutter; 2.1 mm borestandard · 021 / 023 / 025: WT 286 choke bore differs from standard WT 215
Service note · 021 / 023 / 025
021 / 023 / 025: C1Q-S11G discontinued, component spares retained
Walbro WT 215 replaces the complete Zama carburetor; Zama components remain service spares.
- Zama C1Q-S11G 1123 120 0600, previously alternative production equipment, will no longer be installed. Complete carburetor is no longer available from factory; use Walbro WT 215 1123 120 0605 as replacement. The component parts of the Zama carburetor REMAIN available as spares.
- Introduction in progress, no serial given. This complete-carburetor replacement does not establish interchange of Zama and Walbro internal components or carburetor adjustment values.
- Historical TI 13/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 13/1994, p. 2 — 021 / 023 / 025: C1Q-S11G discontinued, component spares retained.
Part numbers (2)
- 1123 120 0600 — Zama C1Q-S11G carburetordiscontinued complete assembly; component spares retained · 021 / 023 / 025: C1Q-S11G discontinued, component spares retained
- 1123 120 0605 — Walbro WT 215 carburetorspecified complete replacement · 021 / 023 / 025: C1Q-S11G discontinued, component spares retained
Wrong number or missing part for the 021, 023, 025? Report a correction →