← 021/023/025 · MS 210/230/250

Stihl 1123 · Section O · 14 of 19 · 39 parts

Handle housing

Fits 021, 023, 025.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262727282933044056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (39)

PosPart numberDescriptionQty
1 1123 790 1003 Handle housing 1
2 1123 790 1008 Handle housing Fitment / change note → 1
3 1128 182 1005 Throttle trigger 1
4 1117 182 0805 Lockout lever 1
5 1117 182 4500 Torsion spring 1
6 9371 470 2640 Cylindrical pin 5x24 1
7 4130 350 6200 Fuel pump Fitment / change note → → replaced by 4128 120 0100 TI 6/2009 1
8 0000 997 0229 NLA Compression spring Fitment / change note → 1
9 not sold separately Hose 2.2x5.4x68 mm, R1 not available as a separate item 1
10 not sold separately Hose 2.2x5.4x196 mm, R1 not available as a separate item 1
11 1125 122 6600 Collar screw Fitment / change note → 2
12 1123 791 7310 Plug 1
13 1123 442 1602 Contact spring 1
14 1123 791 0600 Handle molding 1
15 1123 791 2805 Annular buffer 1
15 1123 791 2806 Annular buffer 1
16 1123 182 1505 Throttle rod Fitment / change note → 1
17 1123 967 1503 Model plate 021 1
17 1123 967 1508 Model plate 021 C 1
17 1123 967 1504 Model plate 023 1
17 1123 967 1506 Model plate 023 L Fitment / change note → 1
17 1123 967 1507 Model plate 023 C 1
17 1123 967 1505 Model plate 025 1
17 1123 967 1509 Model plate 025 C 1
18 1123 141 2200 Manifold 1
19 1123 141 8600 Impulse hose 1
20 1123 141 5600 Baffle plate 1
21 1123 141 4000 Slide 1
22 1123 791 7500 Cover 1
23 1123 182 0901 Switch shaft 1
24 9075 478 3015 Pan head self-tapping screw IS-D4x15 1
25 1123 791 7505 Cover 1
26 1123 791 1700 Handlebar 1
27 9075 478 4155 Pan head self-tapping screw IS-D5x24 3
28 1123 353 7000 NLA Cover Fitment / change note → 1
29 0000 967 3500 NLA Instruction label 1
30 0000 967 3685 Instruction label 1
40 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2802 Hose 2.2x5.4 mm x 1 m, R1 not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 021 / 023 / 025

021 / 023 / 025: easy-start version and market-specific valve omission

Manual primer, decompression valve and ElastoStart are the three described components, but some early easy-start saws omitted the valve.

  • The source introduces easy-start VERSIONS of 021, 023, 025, not a universal replacement of all variants. Manual fuel pump (drawing 1) primes the carburetor metering chamber; the source claims about 40% fewer pulls. This is a historical claim, not a measured guarantee or a claim of 40% less pulling force.
  • Decompression valve (2) is manually opened and automatically closes after firing; ElastoStart grip (3) cushions compression peaks. A NUMBER of easy-start saws up to X 30 950 036 were supplied WITHOUT a decompression valve in SOME markets. This is a qualified omission boundary, not a universal introduction cutoff or proof that every earlier saw lacks the valve.
  • Only the ElastoStart retrofit is expressly authorized across all three model families on page 5. Do not treat the parts roster or this overview as approval to retrofit the entire primer/decompression system.
  • Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.

Source: TI 10/1994, p. 1 — 021 / 023 / 025: easy-start version and market-specific valve omission.

No additional parts-table entry added.

Service note · 021 / 023 / 025

021 / 023 / 025 easy start: primer flow, hose lengths and sealing

68 mm intake goes on the short rearward nipple; 190 mm return goes on the long central nipple.

  • Manual primer 4130 350 6200 is double-acting and mounted in handle housing. PRESSING the bulb closes the intake and opens return, forcing fuel already in the bulb to tank. RELEASING closes return and opens intake; bulb spring action draws fuel from tank pickup/suction hose through carburetor fuel pump, metering system and primer intake hose. It primes through the carburetor, not directly into the cylinder.
  • Carburetor nipple is on the metering side; non-return valve between metering chamber and jet system prevents the primer draining the jet system. Return enters tank through a grommet next to the tank vent. Air initially appears in the bulb and is progressively returned to tank on presses. Depending on trapped air after dry tank/storage, source says 3–8 presses; proper priming leaves an air bubble about the size of a PEA, not necessarily zero bubbles.
  • Remove by disconnecting both hoses, squeezing two spring tabs and pulling pump from seat. Faulty pump CANNOT be repaired and must be replaced. Install with SHORT intake nipple pointing toward REAR HANDLE; push fully home until tabs snap into place.
  • Fit 68 mm intake hose 1123 358 7600 on SHORT nipple; fit 190 mm return hose 1123 358 7601 on LONG nipple near center. Insert helical spring 0000 997 0229 into intake hose to keep its diameter open/prevent kinking, then connect intake to carburetor nipple. Route return through carburetor box and retainers into tank grommet 0000 989 0816. Grommet MUST be fitted for a good seal. Page 5 diagram hose keys 2/3 differ from page 6 roster keys 9/11; keep contexts separate.
  • Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.

Source: TI 10/1994, p. 2 · TI 10/1994, p. 5 · TI 10/1994, p. 6 — 021 / 023 / 025 easy start: primer flow, hose lengths and sealing.

Part numbers (5)
  • 4130 350 6200 — Manual fuel primer, page 6 item 8new easy-start part; replace if faulty · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
  • 1123 358 7600 — 68 mm intake hose, item 9short rearward nipple · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
  • 0000 997 0229 — Intake anti-kink spring, item 10required in intake hose · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
  • 1123 358 7601 — 190 mm return hose, item 11long central nipple · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing
  • 0000 989 0816 — Tank return-hose grommet, item 5required sealing part · 021 / 023 / 025 easy start: primer flow, hose lengths and sealing

Service note · 021 / 023 / 025

021 / 023 / 025 easy start: engine and handle housing inclusion boundaries

Engine housing includes items 2–4; handle housing includes collar screw 7.

  • Engine housing 1123 020 3006 (item 1) includes valve 1128 640 9100 (2), notched pin 2.6x8 0000 974 1200 (3) and collar screw 1123 664 2400 (4). This valve is not decompression valve 1123 020 9400 or primer non-return valve. No valve function beyond this roster is inferred.
  • Handle housing 1123 790 1008 (6) includes collar screw 1125 122 6600 (7). Tank grommet 0000 989 0816 is separately item 5, not within the printed engine-housing items 2–4 or handle-housing item 7 inclusion. The primer service requires the grommet for sealing.
  • Items 2, 3, 4, 7 carry remark 1: included in other versions of 021/023. It is not a new blanket 025 cross-version claim. No unchanged old housing number or whole-system retrofit is stated.
  • Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.

Source: TI 10/1994, p. 5 · TI 10/1994, p. 6 — 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries.

Part numbers (7)
  • 1123 020 3006 — Engine housing, item 1includes 2–4 · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries
  • 1128 640 9100 — Valve, item 2included; remark 1 · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries
  • 0000 974 1200 — Notched pin 2.6x8, item 3included; remark 1 · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries
  • 1123 664 2400 — Collar screw, item 4included; remark 1 · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries
  • 0000 989 0816 — Rubber grommet, item 5separate roster item · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries
  • 1123 790 1008 — Handle housing, item 6includes 7 · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries
  • 1125 122 6600 — Collar screw, item 7included; remark 1 · 021 / 023 / 025 easy start: engine and handle housing inclusion boundaries

Service note · 021 / 023 / 025

Series 1123 throttle rod: 24 mm original offset becomes 38 mm

New rod 1123 182 1505 can replace 1123 182 1500 throughout the historical series 1123 range.

  • Throttle rod 1123 182 1505 is adapted to the 023 L filter system and can be installed in ALL SERIES 1123 chain saws. The original 1123 182 1500 is NO LONGER AVAILABLE FROM THE FACTORY. This is the 1995 scope, not proof for every future MS-series redesign.
  • The drawing labels original LEFT offset a=24 mm (0.94 inch), and new RIGHT offset b=38 mm (1.5 inch). These are the indicated offsets, not total rod lengths. The extracted body corrupts a=24 and b; the original figure controls. Section 5 remark 3 repeats the replacement. Later O handle-housing sheet shows 1505 at key 16.
  • Bound IPL navigation models are 021/023/025. The source explicitly includes 023 L in the series-wide statement, but the canonical structured model list lacks that exact variant; it is not silently renamed 023.
  • Historical TI guidance for the stated variant or accessory only; catalog links and shared numbers are not proof of unrestricted interchange. No serial changeover, current supply guarantee or physical fitment test is implied. No hardware operation was performed.

Source: TI 17/1995, p. 5 · TI 17/1995, p. 10 — Section 2.6 figure 135TI016 and section 5 remark 3.

Part numbers (2)
  • 1123 182 1500 — Original throttle rod24 mm drawing offset; factory supply ended · 021; 023; 025
  • 1123 182 1505 — New throttle rod38 mm drawing offset; historical series 1123 replacement · 021; 023; 025

Service note · 021 / 023 / 025

Series 1123 sprocket cover: replacement remark and misplaced marker

Cover 1123 640 1705 replaces 1123 648 0400; the same printed remark marker on a twist lock remains a source conflict.

  • Section 5 lists chain sprocket cover 1123 640 1705 with remark 2: replaces original 1123 648 0400 on ALL SERIES 1123 saws. Later H chain-brake sheet shows 1705 at key 17. This is the historical 1995 replacement scope, not unlimited compatibility with later redesigns.
  • The ORIGINAL SCAN also puts remark 2 on twist lock 1124 140 9500. Because remark 2 describes replacing a chain sprocket cover, this attachment is internally inconsistent. Retain both printed markers; do NOT create a twist-lock-to-sprocket-cover interchange edge or silently erase the conflict.
  • The table separately lists nameplate 023 L 1123 967 1506. This plate is ONLY for 023 L, not the standard 021/023/025 models used for navigation here. Later O handle-housing sheet key 17 includes this plate among several named variants. A nameplate alone does not convert a saw or identify its power rating.
  • Table item numbers 1–5,7–8 are inclusion references; no item 6 is printed. There are no MOQ, serial cutoffs or dimensional instructions in this parts table. Remark 1 concerns the buffer’s prior use elsewhere; remark 3 concerns the throttle rod, not all listed parts.
  • Historical TI guidance for the stated variant or accessory only; catalog links and shared numbers are not proof of unrestricted interchange. No serial changeover, current supply guarantee or physical fitment test is implied. No hardware operation was performed.

Source: TI 17/1995, p. 10 — Section 5 sprocket-cover/nameplate rows, remarks 1–3 and footer.

Part numbers (4)
  • 1123 640 1705 — Chain sprocket coverremark 2 historical series 1123 replacement · 021; 023; 025
  • 1123 648 0400 — Original chain sprocket coverreplaced by 1123 640 1705 · 021; 023; 025
  • 1124 140 9500 — Twist lockmisplaced remark 2 retained · 021; 023; 025
  • 1123 967 1506 — Nameplate 023 LONLY 023 L; not all navigation models · 023 L only

Service note · 021 / 023 / 025

021/023/025 easy start: primer-hose cover and locating pin

Cover fits behind the primer lug and into a provided 2.5 mm housing hole.

  • Section 2 applies to versions WITH EASY START SYSTEM. Cover 1123 353 7000 protects hoses to the fuel pump in the handle housing; no equivalence to later ErgoStart systems is inferred.
  • Drawing 135TI031: cover (1) locates BEHIND TOP LUG (2) of the primer pump; its integral bottom pin (3) locates in a PROVIDED 2.5 mm (0.1 in.) diameter hole in the handle housing. The handle-housing part number remains unchanged; this TI does not print that number or authorize drilling an older housing.
  • Removal: apply thumb to housing, carefully push cover in the ARROW DIRECTION shown in 135TI032 until it leaves its seat, then remove. Reverse this sequence to install. The arrow points diagonally toward the cover near its lower edge; follow the source view, not an invented universal left/right direction.
  • Table introduces the cover with original column ---; the printed introduction line reads number in progress and supplies NO actual machine number. Later sheet O key 28 retains 1123 353 7000 with a no-longer-available flag, not a substitute or current-stock promise.
  • Historical TI24/1996 guidance only. No serial cutoff is stated; introduction is in progress, not a verified calendar date. Shared IPL sheets do not extend applicability to other variants or MS successor models. Supply statements are historical, not present stock guarantees. No hardware operation was performed.

Source: TI 24/1996, p. 1 · TI 24/1996, p. 2 — 021/023/025 easy start: primer-hose cover and locating pin.

Part numbers (1)
  • 1123 353 7000 — Primer/fuel-pump hose coverNew cover; locating pin and lug engagement · 021/023/025 easy-start versions with stated housing provision

Wrong number or missing part for the 021, 023, 025? Report a correction →