← 021/023/025 · MS 210/230/250

Stihl 1123 · Section Q · 16 of 19 · 46 parts

Carburetor WT-283C, WT-498A, WT-503, WT-313 USA

Fits 021, 023, 025.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192212223242526272829330313233343536373839440414256789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (46)

PosPart numberDescriptionQty
1 1115 121 5401 Valve jet 1
2 4117 122 9402 Plug 1
3 1123 121 5640 Fixed jet 0.53 Fitment / change note → → replaced by 1130 121 5600 TI 34/2001 1
4 1120 121 5600 Fixed jet 0.56 1
5 1123 121 5625 Fixed jet 0.55 Fitment / change note → 1
6 4116 121 5100 Inlet needle 1
7 1120 122 3001 Spring 1
8 1113 121 5000 Inlet control lever 1
9 1113 121 9200 Spindle 1
10 1114 122 7400 Round head screw 1
11 1120 129 0900 Gasket 1
12 1113 121 4705 Metering diaphragm 1
13 1113 121 0800 End cover 1
14 1106 122 7400 Round head screw 4
15 1114 121 7800 Strainer 1
16 1121 121 4801 Pump diaphragm 1
17 1120 129 0905 Gasket 1
18 1123 121 0802 End cover 1
19 1114 122 7100 Screw 1
21 1123 122 6201 Idle speed adjustment screw 1
22 1113 122 3205 Torsion spring 1
23 1123 120 7101 Throttle shaft with lever 1
24 1123 121 3301 Throttle shutter 1
25 1115 122 7400 Round head screw 1
26 1117 122 9000 E-clip 1
27 1123 122 6802 Low speed adjustment screw 1
28 1115 122 3002 Spring 1
29 1111 121 8605 Washer 1
30 4124 122 3600 Sealing ring 1
31 1123 122 3201 Torsion spring 1
32 1123 120 7201 Choke shaft with lever 1
33 1110 122 7400 Round head screw 1
34 1123 122 9000 E-clip 1
35 1123 122 3900 Elbow connector 1
36 1123 121 2901 Choke shutter 1
37 4130 122 3905 Connector 1
38 4133 120 8600 Non-return valve 1
39 4117 122 6200 Idle speed adjustment screw 1
40 1129 121 5600 Fixed jet 0.50 option 1
41 1121 121 5604 Fixed jet 0.48 option 1
42 not sold separately Fixed jet 0.60 no longer available from factory 1
Not numbered on the diagram — assemblies, kits and options
— 1123 120 0614 Carburetor WT-503A Fitment / change note → 1
— 1123 120 0610 Carburetor WT-283C Fitment / change note → 1
— 1123 120 0616 Carburetor WT-498A 1
— not sold separately Carburetor WT-313 no longer available from factory
— 1123 007 1061 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 025

025 California: WT283A replaces WT313 at its own cutoff

WT283A is already used on 021 and 023; the change applies to 025 California only.

X 34 191 135 — 025 California WT313 to WT283A change only; independent of 021 crank drive.

  • For 025 CALIFORNIA ONLY, from X 34 191 135, original WT 313 carburetor 1123 120 0612 is replaced by WT 283 A 1123 120 0610. WT283A is already installed in models 021 and 023 and already supplied as a spare for them; that context does not give those models a new cutoff.
  • Table item 1 WT313 explicitly includes item 3, fixed jet 1123 121 5615. The original WT313 assembly and that jet are NO LONGER AVAILABLE FROM THE FACTORY under remark 1. New WT283A is remark 2, already a spare for 021/023. Do not turn the table dash in the old-carburetor row into a claim that no replacement assembly exists.
  • The source says spare parts for these TWO carburetors are identical EXCEPT fixed jets. This is not a statement about every later carburetor listed on the IPL sheet: its WT-283C label is not silently substituted for the source WT283A. No calibration settings or current emissions certification is established. Last-TI reference 38/1996 is bibliographic context, not a dependent procedure.
  • Historical TI13/1997 evidence for the exact named model/configuration only. Shared IPL labels are discovery links, not applicability to every model or later carburetor suffix on that sheet. Availability statements describe 1997, not current stock. No successor-model scope, universal retrofit or tested interchange is inferred. No hardware operation was performed.

Source: TI 13/1997, p. 4 — 025 California: WT283A replaces WT313 at its own cutoff.

Part numbers (2)
  • 1123 120 0612 — Original WT313 carburetor; includes item 3No longer available from factory · 025; 025 California: WT283A replaces WT313 at its own cutoff
  • 1123 120 0610 — New WT283A carburetorReplacement; already spare for 021/023 · 025; 025 California: WT283A replaces WT313 at its own cutoff

Service note · 025

025 California WT313: permitted replacement fixed jet

Deleted 0.6 mm jet 5615 may be replaced by 5610; its diameter is not stated.

  • Fixed jet 1123 121 5615, DIAMETER 0.6 mm, is the deleted WT313 jet and table item 3 included in old carburetor item 1. The source explicitly permits fixed jet 1123 121 5610 as a replacement IN WT313.
  • NO diameter is given for replacement jet 1123 121 5610 on this page. Do not transfer the deleted jet’s 0.6 mm dimension to it, infer reciprocal interchange, or identify it as the WT283A production jet without separate evidence. The table omits a new jet number, but the preceding prose supplies the permitted replacement.
  • The independent X 34 191 135 cutoff concerns the 025 California carburetor production change. It does not limit this old-WT313 service-jet statement to post-cutoff machines. The common-spares claim excludes fixed jets and remains limited to WT313 / WT283A.
  • Historical TI13/1997 evidence for the exact named model/configuration only. Shared IPL labels are discovery links, not applicability to every model or later carburetor suffix on that sheet. Availability statements describe 1997, not current stock. No successor-model scope, universal retrofit or tested interchange is inferred. No hardware operation was performed.

Source: TI 13/1997, p. 4 — 025 California WT313: permitted replacement fixed jet.

Part numbers (2)
  • 1123 121 5615 — Deleted WT313 fixed jet, diameter 0.6 mmNo longer available from factory · 025; 025 California WT313: permitted replacement fixed jet
  • 1123 121 5610 — Permitted WT313 replacement fixed jet; diameter unstatedConditional service replacement · 025; 025 California WT313: permitted replacement fixed jet

Conditional replacement · 021

021: WT 503 and the 0.53 mm repair jet

WT 283 A changes to WT 503; repair permission covers both named versions.

X 37 731 266 — Production introduction of the model-specific smaller fixed jets and carburetor designations; not a model identity range or a lower limit on repair eligibility.

  • Historical TI08/1998: smaller fixed-jet orifices allow for the fleece air filter introduced in TI38/1996. Production modification is printed FROM machine number X 37 731 266; retain the X prefix and do not turn it into a model-identification range. The service permissions apply IN CASE OF A REPAIR and are not restricted to post-cutoff machines. Factory availability is historical, not current stock. No successor-model scope or verified physical interchange is inferred. No hardware operation was performed.
  • 021 production changes from WT 283 A, fixed jet 0.57 mm, to WT 503, fixed jet 0.53 mm. Summary item 1 original carburetor 1123 120 0610 includes item 4 jet 1123 121 5610; new item 2 carburetor 1123 120 0614 includes item 5 jet 1123 121 5640. Do not use the 023/025 0.55 mm branch for 021.
  • Fixed jet 1123 121 5640, DIAMETER 0.53 mm, MAY BE INSTALLED in WT 283 A AND WT 503 on 021 IN CASE OF A REPAIR. The permission names both old and new carburetors, not every WT series carburetor.
  • With the EXCEPTION OF FIXED JETS, the parts of WT 283 A, WT 503 and WT 283 B are identical according to this TI. That exception is essential; no identical-parts claim is made here for WT 498/WT 498 A or later WT 503A/WT 283C.
  • The old 0.57 mm jet 1123 121 5610 is DELETED WITHOUT REPLACEMENT as a supply item. This does not cancel the explicitly permitted model-specific smaller repair jets. Summary remark 1 says original WT 283 A and old jet are NO LONGER AVAILABLE FROM FACTORY; it does not withdraw the reused 0610 number in its new 023/025 WT 283 B configuration.
  • The later 2012 IPL describes 1123 120 0614 as WT-503A, while TI08 says WT 503. Preserve that suffix difference. Its 0.53 jet row has a later TI34/2001 supersession annotation; that is not the 1998 instruction or proof of equal calibration. TI38/1996 fleece-filter guidance is already source-reviewed; no filter conversion procedure is invented here.

Source: TI 8/1998, p. 1 · TI 8/1998, p. 2 — 021 matrix/service note, common parts/deletion prose and summary items1,2,4,5/remark1.

Referenced bulletin evidence: TI 38/1996, p. 1 — Fleece filter change; already reviewed source context.

Part numbers (4)
  • 1123 120 0610 — WT 283 A; includes old jet item 4Original for 021 · 021; exact carburetor version and repair restrictions in this note
  • 1123 120 0614 — WT 503; includes 0.53 jet item 5New for 021 · 021; exact carburetor version and repair restrictions in this note
  • 1123 121 5610 — Fixed jet 0.57 mmDeleted without replacement; old version unavailable · 021; exact carburetor version and repair restrictions in this note
  • 1123 121 5640 — Fixed jet 0.53 mmNew; permitted repair jet for 021 WT 283 A / WT 503 · 021; exact carburetor version and repair restrictions in this note

Conditional replacement · 023 / 025

023 / 025: WT 283 B retains the 0610 number

0.55 mm repair jet covers WT 313, WT 283 A and WT 283 B.

X 37 731 266 — Production introduction of the model-specific smaller fixed jets and carburetor designations; not a model identity range or a lower limit on repair eligibility.

  • Historical TI08/1998: smaller fixed-jet orifices allow for the fleece air filter introduced in TI38/1996. Production modification is printed FROM machine number X 37 731 266; retain the X prefix and do not turn it into a model-identification range. The service permissions apply IN CASE OF A REPAIR and are not restricted to post-cutoff machines. Factory availability is historical, not current stock. No successor-model scope or verified physical interchange is inferred. No hardware operation was performed.
  • 023 and 025 production changes from WT 283 A with a 0.57 mm fixed jet to WT 283 B with a 0.55 mm fixed jet. BOTH carburetor versions use 1123 120 0610. Summary item 1 original includes item 4 jet 1123 121 5610; new item 3 includes item 6 jet 1123 121 5625. An unchanged assembly number does not identify the installed jet or suffix.
  • Fixed jet 1123 121 5625, DIAMETER 0.55 mm, MAY BE INSTALLED in WT 313, WT 283 A AND WT 283 B for the 023/025 service heading IN CASE OF A REPAIR. The TI specifically identifies WT 313 as the predecessor to WT 283 A IN MODEL 025; it does not establish WT 313 as an original 023 production carburetor.
  • TI13/1997 page4 scoped the earlier 025 WT313-to-WT283A production change to CALIFORNIA and X 34 191 135. It permitted 1123 121 5610 as a WT313 repair jet without giving its diameter. TI08/1998 now supplies the 0.57 mm identity of 5610, deletes it and permits 0.55 mm 1123 121 5625. Preserve the earlier source and scope; neither its cutoff nor its old repair permission overrides this later instruction. TI08 does not print a California-only qualifier on its 023/025 service heading.
  • Except for FIXED JETS, WT 283 A, WT 503 and WT 283 B parts are said to be identical. Their model-conditioned jet sizes remain different. Original WT 283 A and 0.57 mm jet 1123 121 5610 carry remark 1: NO LONGER AVAILABLE FROM FACTORY. The jet is DELETED WITHOUT REPLACEMENT as a supply item, alongside the explicit smaller-jet repair permission; do not flatten this into a universal supersession.
  • The later shared 2012 IPL calls 1123 120 0610 WT-283C, not the WT 283 B in TI08. It retains 1123 121 5625 described as 0.55. The later sheet is navigation/comparison evidence, not a reason to rewrite this historical B suffix or extend scope to successor models.

Source: TI 8/1998, p. 1 · TI 8/1998, p. 2 — 023/025 matrix and full repair note, TI13 predecessor reference, summary items1,3,4,6/remark1.

Referenced bulletin evidence: TI 13/1997, p. 4 — Earlier California WT313 replacement and repair jet; retain edition scope.

Part numbers (3)
  • 1123 120 0610 — WT 283 A to WT 283 B; same number, different jet inclusionOriginal and modified versions · 023, 025; exact carburetor version and repair restrictions in this note
  • 1123 121 5610 — Fixed jet 0.57 mm; original item 4Deleted without replacement · 023, 025; exact carburetor version and repair restrictions in this note
  • 1123 121 5625 — Fixed jet 0.55 mm; new item 6New and permitted repair jet for named carburetors · 023, 025; exact carburetor version and repair restrictions in this note

Wrong number or missing part for the 021, 023, 025? Report a correction →