Stihl 1124 · Section L · 11 of 15 · 35 parts
Carburetor HT-7A
Fits 084.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1110 122 9410 | Plug | 1 |
| 2 | 1124 121 5601 | Fixed jet 0.90 | 1 |
| 3 | 1124 121 5403 | Valve jet | 1 |
| 4 | 1124 121 2900 | Choke shutter | 1 |
| 5 | 1106 122 7400 | Round head screw | 2 |
| 6 | 1124 122 3200 | Torsion spring | 1 |
| 7 | 1124 120 7200 | Choke shaft with lever | 1 |
| 8 | 1110 129 0900 | Gasket | 1 |
| 9 | 1110 121 4700 | Metering diaphragm | 1 |
| 10 | 1124 121 0803 | End cover | 1 |
| 11 | 1124 122 7102 | Screw | 4 |
| 12 | 1124 121 4800 | Pump diaphragm | 1 |
| 13 | 1110 129 1110 | Gasket | 1 |
| 14 | 1124 121 0802 | End cover | 1 |
| 15 | 1110 122 7700 | Oval head screw | 4 |
| 16 | 1124 122 6801 | Low speed adjustment screw | 1 |
| 17 | 1124 122 6701 | High speed adjustment screw | 1 |
| 18 | 1124 121 5000 | Inlet control lever | 1 |
| 19 | 1124 122 3000 | Spring → replaced by 1124 122 3001 TI 34/1997 | 1 |
| 20 | 1110 121 9200 | Spindle | 1 |
| 21 | 1110 122 7800 | Oval head screw | 1 |
| 22 | 1110 121 5100 | Inlet needle | 1 |
| 23 | 4221 121 7800 | Strainer | 1 |
| 24 | 1124 122 6200 | Idle speed adjustment screw | 1 |
| 25 | 1124 122 5400 | Sleeve | 2 |
| 26 | 1124 121 7700 | Clamp | 1 |
| 27 | 1110 122 9005 | E-clip | 2 |
| 28 | 1124 121 8600 | Washer | 1 |
| 29 | 1124 122 3210 | Torsion spring | 1 |
| 30 | 1124 120 7100 | Throttle shaft with lever | 1 |
| 31 | 1124 121 3301 | Throttle shutter | 1 |
| 32 | 1124 121 0801 | End cover | 1 |
| 33 | 1106 122 7400 | Round head screw | 4 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1124 120 0607 | Carburetor HT-7A Fitment / change note → | 1 |
| — | 1124 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 084
084: optional 0.88 mm jet for HT-7 A
Optional high-altitude jets selected by stamped carburetor type; exact table associations and restrictions retained.
- Use ONLY the type designation stamped on the carburetor body, not the saw model or carburetor part number alone. Each row below retains its exact printed suffix; later suffixes and MS successor models are not admitted by a shared number or sheet.
- These are OPTIONAL smaller-bore high-altitude jets, not standard jets or unconditional replacements. For adjustable carburetors WITH a semi-fixed jet, TI29/1998 permits leaner adjustment down to H = 0 if necessary; the smaller-bore option is for very high altitude when that range is insufficient. This is not a universal H setting for other designs and no numeric altitude threshold is supplied.
- Do NOT use the smaller-bore high-altitude jets at lower altitudes: an overly lean mixture can cause engine damage. Replacement is for trained personnel; press-fit positioning depends on the separate Carburetors handbook. No complete installation procedure, regulatory approval or physical interchange test is claimed. No hardware operation was performed.
- HT 7 A: carburetor 1124 120 0607; optional fixed jet 1124 121 5606, bore 0.88 mm; source model 084. No USA-only asterisk is printed on this row.
- The retained exact HT-7A sheet lists fixed jet 1124 121 5601 at 0.90 mm; this optional 0.88 mm item remains a historical overlay, not a fabricated replacement of its standard row.
Source: TI 29/1998, p. 1 · TI 29/1998, p. 2 — Page 1 complete guidance and page 2 HT 7 A table rows.
Part numbers (2)
- 1124 120 0607 — Carburetor HT 7 ASource type association · 084; stamped HT 7 A only
- 1124 121 5606 — High-altitude fixed jet, 0.88 mmOptional, not standard · HT 7 A; 084; high-altitude conditions only
Wrong number or missing part for the 084? Report a correction →