Stihl 1124 · Section B · 2 of 14 · 26 parts
Cylinder, Muffler
Fits 088.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (26)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1124 020 1207 | Cylinder with piston Ø 60 mm → replaced by 1124 020 1209 TI 9/2009 | 1 |
| 2 | 1124 030 2007 | Piston Ø 60 mm Fitment / change note → | 1 |
| 3 | 1124 034 3010 | Piston ring Ø 60x1.2 mm | 2 |
| 4 | 1124 034 1500 | Piston pin 13x8x39 | 1 |
| 5 | 9463 650 1300 | Snap ring 13x1 | 2 |
| 6 | 0000 953 0818 | Stud M5 | 1 |
| 7 | 1124 020 9410 | Decompression valve | 1 |
| 8 | 1122 084 1405 | Cover Fitment / change note → | 1 |
| 9 | 9022 341 1370 | Spline screw IS-M6x30 | 4 |
| 10 | 1124 029 2310 | Cylinder gasket | 1 |
| 11 | 9512 003 3440 | Needle cage 13 x17x17.5 | 1 |
| 12 | 1124 149 0610 | Muffler gasket | 1 |
| 13 | 1124 140 0625 | Muffler → replaced by 1124 140 0604 TI 9/2009 | 1 |
| 14 | 1124 145 2905 | Muffler cover | 1 |
| 15 | 1124 141 9005 | Screen | 1 |
| 16 | 1124 140 0620 | Muffler | 1 |
| 17 | 1124 145 2900 | Muffler cover | 1 |
| 18 | 9022 313 0660 | Spline screw IS-M4x12 | 4 |
| 19 | 1124 145 1905 | Tension wedge | 2 |
| 20 | 1124 145 1800 | Tension spring | 1 |
| 21 | 1124 145 2005 | Support | 2 |
| 22 | 9291 021 0120 | Washer 5.3 | 4 |
| 23 | 9022 341 0980 | Spline screw IS-M5x16 | 4 |
| 24 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 25 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1124 007 1051 | Set of gaskets 088 Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 088
088: engine, intake flange and cooling changes
A wider big-end bearing and lightweight flywheel distinguish the launch construction from 084.
- The illustrated new intake flange (1) is described as improving airflow and torque. The crankshaft has a wider big-end bearing, with strengthened crankshaft and crankcase. No dimensions, ordering numbers or cross-model swap permission are supplied.
- The cylinder has increased cooling surface area. A lightweight flywheel with polymer fan and small high-power magnets is described as increasing cooling air volume by approximately 20%, improving acceleration from idle to maximum speed, handling and control, and reducing main-bearing load.
- These are historical manufacturer design claims relative to 084, not measurements reproduced here. No introduction serial, 084 retrofit or later MS880 applicability is inferred.
Source: TI 35/1996, p. 1 · TI 35/1996, p. 3 — Cover and sections1.3–1.5.
No additional parts-table entry added.
Historical fitment · 088
088: decompression valve and protective cover
Cover 1122 084 1405 sits between cylinder and shroud.
- The complete valve screws into the cylinder. Its axial plunger has a conical lower end, retained in upper or lower position by three spring-loaded balls offset 120 degrees. Diagram labels are body (1), plunger (2), balls (3), not separate orderable part numbers.
- Pushing the plunger down opens the bore before starting. During cranking, part of the cylinder pressure escapes through that bore; remaining compression stays below closing pressure. After ignition, pressure lifts the plunger and the cone closes the bore. No numeric opening or closing pressure is given.
- The shroud opening has a raised surround to protect against accidental valve contact. Cover 1122 084 1405 is installed between cylinder and shroud to help exclude dust and dirt. This cover is not the complete shroud or valve.
- The stated benefit is reduced starter-rope effort. Construction description is not authorization to operate hardware or evidence of a valve rebuild procedure.
Source: TI 35/1996, p. 1 · TI 35/1996, p. 4 — Cover and section1.6 complete construction/function, drawings137TI006/007 and171TI003.
Part numbers (1)
- 1122 084 1405 — Decompression-area coverRequired cover · 088; between cylinder and shroud
Service note · 088
088: cast muffler mounting
Two wedges and one spring attach the muffler to the cylinder; two straps attach it to the crankcase.
- The launch 088 uses a large baffled cast lightmetal muffler for improved silencing. The drawing labels muffler (1), two wedges (2), spring (3) and cylinder (4).
- Two straps (5) secure the muffler to crankcase (6). These are distinct cylinder-side and crankcase-side attachments; drawing callouts are not ordering numbers.
- No clamp torque, strap interchange, 084 retrofit or later muffler-generation applicability is supplied.
Source: TI 35/1996, p. 5 — Section1.7 and drawings171TI004/005.
No additional parts-table entry added.
Historical fitment · 088
088: gasket and carburetor service aids
Launch servicing-aid numbers do not establish kit contents.
- Gasket set 088 1124 007 1051, carburetor parts kit 1124 007 1060 and gasket panel 088 0457 281 2204 are listed as new servicing aids. Contents are not enumerated; no kit-to-every-later-carburetor assertion is inferred from the linked IPL assembly.
- Other tools/aids and general tightening torques are referred to the separate 088 service manual. No unstated torque is filled in from 084 or a successor model.
- The bulletin says all repair times are the same as 084, but gives no operation-by-operation times. It also announces a separate 088 illustrated parts list; neither statement proves another document was reviewed here.
- If started during repairs or maintenance, the source requires compliance with local regulations and owner-manual safety precautions. This offline reference work does not start a machine.
Source: TI 35/1996, p. 7 · TI 35/1996, p. 8 — Sections4.2,5 repair preface,5.3–5.4 and6.
Part numbers (3)
- 1124 007 1051 — 088 gasket setServicing aid · 088; contents unspecified
- 1124 007 1060 — Carburetor parts kitServicing aid · 088; launch carburetor; contents unspecified
- 0457 281 2204 — 088 gasket panelServicing aid · 088; not a torque table
Historical fitment · 088
088: locking strip and cylinder removal precautions
Close the decompression valve before inserting the locking strip.
- Locking strip 0000 893 5903 blocks the crankshaft via the spark-plug hole. It must not be inserted until the decompression valve is closed; if open, piston/strip force can bend the valve.
- Before lifting the cylinder off the piston, use a knife to separate the gasket from the cylinder base, as illustrated, to prevent the piston snagging the gasket edge and being damaged.
- These are the printed service precautions, not a complete dismantling sequence, cutting-depth specification or permission to apply arbitrary crankshaft force.
Source: TI 35/1996, p. 7 — Sections5.1.1–5.1.2 and drawing137TI002.
Part numbers (1)
- 0000 893 5903 — Locking stripConditional service tool · 088; only with decompression valve closed
Historical fitment · 088
088: leakage-test preparation and pressures
Replace the decompression valve with the specified plug before the test.
- Flange 1124 850 4205 seals the muffler opening for leakage testing. Plug 1122 025 2200 must be installed instead of the decompression valve before the leakage test; the source refers to the service manual for the full procedure.
- The decompression valve is removed/installed with a standard deep-well 13-mm socket. The adjacent tightening torque is 14 Nm (10.3 lbf.ft); do not apply it as a general cylinder, flange or carburetor torque.
- Printed engine pressure test: 0.6 bar (8.7 psi); engine vacuum test: 0.6 bar (8.7 psi). The vacuum value is a magnitude in the vacuum-test row, not positive pressure or an absolute-pressure statement. Carburetor pressure test: 0.4 bar (5.8 psi).
- No dwell time, permissible leak-down, complete port-sealing sequence or carburetor setup is printed. These values alone are not a complete executable test or a verified test result.
Source: TI 35/1996, p. 7 · TI 35/1996, p. 8 — Section4.1 flange and section 5.2.1 entire test data.
Part numbers (2)
- 1124 850 4205 — Muffler-opening sealing flangeLeakage-test tool · 088; muffler opening
- 1122 025 2200 — Decompression-port plugLeakage-test prerequisite · 088; replaces decompression valve
Service note · 088
088 from production start: piston 2007 and clutch 2005
The 084 service replacements were already fitted to the 088 from the beginning.
- TI17 explicitly says piston 1124 030 2007 and clutch 1124 160 2005 have been installed in model 088 since the START OF PRODUCTION. These are existing 088 production facts, not a 1997 replacement or a new 088 cutoff. No production-start date is given.
- The piston has a reinforced pin boss, optimized lubricating recesses and SIX CROSSES in two columns of three. The clutch is identified as "05" in prose and "/05" after a boxed mark in the original drawing. No dimensional or test result is inferred from either identification illustration.
- The 084-only sections announce these assemblies as 084 replacements. Do NOT transfer their old-piston deletion or old-clutch/component stock rules to an unstated earlier 088 design. The separate carburetor section is the 088 change in this bulletin.
- Historical TI17/1997 evidence for the named model and section only. No serial cutoff is supplied. Factory availability describes the bulletin date, not present stock. No MS880/MS881 scope, reciprocal component interchange or physical verification inferred. No hardware operation was performed.
Source: TI 17/1997, p. 1 · TI 17/1997, p. 2 — 088 from production start: piston 2007 and clutch 2005.
Part numbers (2)
- 1124 030 2007 — Piston with reinforced boss and six crosses088 from start of production · 088; 088 from production start: piston 2007 and clutch 2005
- 1124 160 2005 — Clutch with 05 identification088 from start of production · 088; 088 from production start: piston 2007 and clutch 2005
Wrong number or missing part for the 088? Report a correction →