← 084 · 088 · MS 780/880/881

Stihl 1124 · Section A · 1 of 14 · 31 parts

Crankcase

Fits 088.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11101112131415161718192202122232425262728293330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 1124 020 2116 Crankcase 1
2 0000 988 5215 Connector 1
3 9371 470 2610 Cylindrical pin 5x18 2
4 1120 162 5200 Pin 1
5 1121 162 5205 Pin 1
6 1121 162 5200 Pin 2
7 0000 974 1200 Notched pin 2.6x8 1
8 1124 640 9100 Valve 1
9 9465 620 2720 Snap ring 47 1
10 9523 003 4386 Grooved ball bearing 20x47x15 1
11 9523 003 4385 Grooved ball bearing 20x47x15 1
12 9503 003 6676 Grooved ball bearing 6203 1
13 1124 664 2406 Collar screw 2
14 9022 341 1050 Spline screw IS-M5x25 8
15 9022 341 1310 Spline screw IS-M6x18 2
16 9022 341 0980 Spline screw IS-M5x16 2
17 1124 647 9400 Hose 1
18 1117 640 3800 Pickup body 1
19 9640 003 2250 Oil seal B20x39x4 1
20 9640 003 1855 Oil seal 17x32.9x5 1
21 1124 029 0510 Gasket → replaced by 1124 029 0501 TI 9/2009 1
22 1124 030 0404 Crankshaft 1
23 1120 036 8500 Woodruff key 2x3.7 1
24 0000 350 0525 Filler cap 1
25 9645 948 7734 O-ring 25x3.5 1
26 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
27 0000 359 1220 Sealing ring 1
28 0000 350 0900 Rope 1
29 0000 353 0600 Hook 1
30 1125 791 2810 Stop buffer 1
Not numbered on the diagram — assemblies, kits and options
— 1124 007 1051 Set of gaskets 088 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 088

088: engine, intake flange and cooling changes

A wider big-end bearing and lightweight flywheel distinguish the launch construction from 084.

  • The illustrated new intake flange (1) is described as improving airflow and torque. The crankshaft has a wider big-end bearing, with strengthened crankshaft and crankcase. No dimensions, ordering numbers or cross-model swap permission are supplied.
  • The cylinder has increased cooling surface area. A lightweight flywheel with polymer fan and small high-power magnets is described as increasing cooling air volume by approximately 20%, improving acceleration from idle to maximum speed, handling and control, and reducing main-bearing load.
  • These are historical manufacturer design claims relative to 084, not measurements reproduced here. No introduction serial, 084 retrofit or later MS880 applicability is inferred.

Source: TI 35/1996, p. 1 · TI 35/1996, p. 3 — Cover and sections1.3–1.5.

No additional parts-table entry added.

Service note · 088

088: 084 comparison specifications

Keep maximum-power speed, permissible speed and mean idle speed distinct.

  • The comparison is printed in 084 / 088 order: engine speed at maximum power 9,300 / 8,500 rpm; maximum torque 7.5 Nm (5.5 lb.ft) / 8.0 Nm (5.9 lb.ft), both at 6,000 rpm.
  • Weight 9.4 kg (20.7 lb) / 9.9 kg (21.8 lb); power-to-weight ratio 1.5 / 1.6 kg/kW. This table does not specify a dry-weight or cutting-attachment convention; do not invent one or derive an exact power rating from rounded ratios.
  • Fuel capacity 1250 cm³ (2.64 US pt) / 1300 cm³ (2.75 US pt); oil capacity 630 cm³ (1.33 US pt) / 700 cm³ (1.48 US pt).
  • Maximum permissible speed with Rollomatic bar and chain is 12,500 / 12,000 rpm; mean idle speed is 2,000 / 2,500 rpm. Neither is the speed at maximum power, nor a general unloaded adjustment target.
  • The air-filter comparison is 084 oil-impregnated cotton HD versus 088 wire mesh (winter option) and dry element. It does not apply the 088 no-oil rule to the original 084 filter.
  • Sound pressure Lpeq to ISO 7182 is 102 / 101 dB(A); sound power Lweq to ISO 9207 is 111 / 112 dB(A). Superscript 1 is printed after both standards but no explanatory footnote appears on the retained page; test-condition detail is not invented.
  • These are dated comparison values, not new measurements, complete engine specifications or automatic applicability to later 084/088 revisions and MS successors.

Source: TI 35/1996, p. 6 — Section2 entire084/088 comparison table.

No additional parts-table entry added.

Wrong number or missing part for the 088? Report a correction →