← 084 · 088 · MS 780/880/881

Stihl 1124 · Section F · 6 of 14 · 21 parts

Ignition system

Fits 088.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819234567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (21)

PosPart numberDescriptionQty
1 1124 400 1210 Flywheel Fitment / change note → → replaced by 1124 400 1201 TI 9/2009 1
2 9211 260 1340 Hexagon nut M10x1 1
3 1124 400 1309 Ignition module EY-V Fitment / change note → → replaced by 1124 400 1301 TI 56/2003 1
4 not sold separately Ignition lead 200 mm not available as a separate item 1
5 0000 989 1010 Grommet 1
6 1125 448 1201 Lead retainer 1
7 1124 440 1101 Short circuit wire → replaced by 1124 440 3000 TI 9/2009 1
8 1119 442 7000 Contact sleeve no longer available from factory 1
9 0751 030 8953 NLA Terminal socket 4.8-1 no longer available from factory 1
10 1124 440 2200 Ground wire 1
11 0751 030 8969 Terminal socket A5-1.5 no longer available from factory 1
12 1121 405 8001 Insulating hose 90 mm / 3.5'' 1
13 1124 442 0400 NLA Insulating hose 160 mm / 6.3'' 1
14 9291 021 0120 Washer 5.3 3
15 9022 341 1050 Spline screw IS-M5x25 3
16 1128 405 1000 Spark plug boot 1
17 0000 998 0604 Torsion spring 1
18 0000 989 1004 Grommet 2
19 1128 084 1400 Cover 1
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m option 1
— 0000 930 2251 Ignition lead 10 m option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 088

088: engine, intake flange and cooling changes

A wider big-end bearing and lightweight flywheel distinguish the launch construction from 084.

  • The illustrated new intake flange (1) is described as improving airflow and torque. The crankshaft has a wider big-end bearing, with strengthened crankshaft and crankcase. No dimensions, ordering numbers or cross-model swap permission are supplied.
  • The cylinder has increased cooling surface area. A lightweight flywheel with polymer fan and small high-power magnets is described as increasing cooling air volume by approximately 20%, improving acceleration from idle to maximum speed, handling and control, and reducing main-bearing load.
  • These are historical manufacturer design claims relative to 084, not measurements reproduced here. No introduction serial, 084 retrofit or later MS880 applicability is inferred.

Source: TI 35/1996, p. 1 · TI 35/1996, p. 3 — Cover and sections1.3–1.5.

No additional parts-table entry added.

Historical fitment · 088

088: series 1124 replacement ignition assignment

1124 400 1309 and the listed flywheel pairing for series 1124; 200 mm ignition lead.

  • Listed configuration: 1124 400 1309 with flywheel 1124 400 1210.
  • Printed ignition-lead length: 200 mm (7 7/8 in). Preserve the printed metric and inch values; no rounding correction is inferred.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.

Part numbers (2)
  • 1124 400 1309 — Replacement ignition moduleAssigned replacement · 088, series 1124, only with the listed flywheel branch
  • 1124 400 1210 — Listed configuration flywheelRequired pairing · 088, series 1124; listed configuration only

Wrong number or missing part for the 088? Report a correction →