← 034 · 036 · MS 340/360

Stihl 1125 · Section S · 18 of 19 · 26 parts

Heating

Fits 034.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252634556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (26)

PosPart numberDescriptionQty
1 1121 440 2201 NLA Ground wire 1
2 1110 432 9200 Grommet 1
3 1121 430 0200 Heating switch 1
4 1128 434 5000 NLA Heating element Fitment / change note → 1
5 1118 431 6700 NLA Terminal socket no longer available from factory 1
6 1118 431 6600 NLA Terminal pin no longer available from factory 1
7 1125 790 1702 Handlebar Fitment / change note → 1
8 1124 442 0400 NLA Insulating hose 160 mm / 6.3'' 1
9 0000 442 7000 NLA Contact sleeve no longer available from factory 1
10 0000 989 0815 Grommet 1
11 1121 791 9000 NLA Clamp 1
12 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' 2
13 1121 442 0406 NLA Insulating hose 40 mm / 1.6'' 1
14 1125 442 0401 NLA Hose 15mm / 5/8'' 1
15 9074 478 4435 Pan head self-tapping screw IS-P6x19 2
16 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 2
17 0000 989 0808 Grommet 1
18 1121 434 5000 NLA Heating element 1
19 9294 021 0140 Washer 6.4 2
20 1125 790 1707 NLA Handlebar Fitment / change note → → replaced by 1125 790 1702 TI 28/1995 1
21 1125 434 5000 NLA Heating element Fitment / change note → 1
22 1118 400 4000 NLA Generator 1
23 1118 431 6600 NLA Terminal pin no longer available from factory 1
24 9041 216 0540 NLA Pan head screw M3.5x12 3
25 1125 400 1205 NLA Flywheel 1
26 1121 405 1900 NLA Support 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 034 / 036

034 / 036 heated-handle flywheel:1208 replaces 1207

Up to 45% more generator output, RPM-dependent; retain matched-heater rule.

  • ONLY MODELS WITH HEATED HANDLES. New flywheel 1125 400 1208 replaces 1125 400 1207 in connection with introduction of a carburetor-heating version. A more powerful permanent magnet increases generator output by UP TO 45%, DEPENDING ON RPM; not a guaranteed 45% increase at all speeds and not a saw-engine power increase.
  • Original figure left identifies the old flywheel with 11 mm (printed 1/2 inch); right identifies the new with 6 mm (printed 1/4 inch) at the indicated magnet feature. Preserve those diagram dimensions and nominal fractions without silently making them exact conversions or calling them overall magnet diameter/strength. More powerful does not imply a larger indicated dimension.
  • Original flywheel no longer factory available; introduction IN PROGRESS. If fitting 1208 to a saw UP TO X 31 813 247, BOTH new front handle 1125 790 1702 AND rear element 1128 434 5000 are required; rear element must be bonded. Original front 1707 or rear element 1125 434 5000 may ONLY be fitted with old flywheel 1207. Do not use the output change as unconditional interchange approval.
  • Later 036 F key 23 lists 1208, while 034 S key 25 lists 1205. That catalog difference is retained, not used to substitute 1205 for the TI 1207/1208 pair or erase the 034 heated-handle source scope.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 4 · TI 28/1995, p. 5 — Section 4.1 flywheel figure and section 4 service restrictions.

Part numbers (2)
  • 1125 400 1207 — Original heated-handle flywheelreplaced · 034 / 036; Section 4.1 flywheel figure and section 4 service restrictions
  • 1125 400 1208 — Higher-output heated-handle flywheelreplacement; matched heaters required · 034 / 036; Section 4.1 flywheel figure and section 4 service restrictions

Service note · 034 / 036

034 / 036 heater identification: resistance at 25°C

Front 1.44–1.76 to 6.3–7.7Ω; rear 0.225–0.275 to 0.9–1.1Ω.

  • Resistance values apply at +25°C (77°F): FRONT heating element original 1.44–1.76 ohms, new 6.3–7.7 ohms; REAR element original 0.225–0.275 ohms, new 0.9–1.1 ohms. Keep front/rear and original/new axes distinct; these are not summed circuit resistances or temperature-independent limits.
  • Front handle 1125 790 1707 is replaced by 1125 790 1702 with higher-resistance heating element. Different front handles can be identified by the table resistance. No separate front-element ordering number is supplied by this TI.
  • Rear element 1125 434 5000 is replaced by 1128 434 5000. Original figure left shows old printed tracks; new element right has THINNER CONDUCTORS IN WAVY LINES. This is a visual distinction, not an inferred conductor thickness or revised wiring diagram.
  • Original front handle and rear element remain available FOR OLDER MACHINES, but may ONLY be fitted with flywheel 1125 400 1207. Installing new 1208 on a saw up to X 31 813 247 requires both new heaters. No meter-lead correction, disconnected-circuit method or tolerance beyond the printed ranges is supplied.
  • Later 034 S keys 7/20 and 036 J keys 13/14 retain new/old handle numbers;034 S keys 4/21 and 036 Q keys 4/5 retain new/old rear elements. Co-listing does not waive the matched-flywheel restriction.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 4 · TI 28/1995, p. 5 — Section 4.2 figure and resistance table.

Part numbers (4)
  • 1125 790 1707 — Original heated front handle1.44–1.76 ohms at 25°C · 034 / 036; Section 4.2 figure and resistance table
  • 1125 790 1702 — New heated front handle6.3–7.7 ohms at 25°C · 034 / 036; Section 4.2 figure and resistance table
  • 1125 434 5000 — Original rear heating element0.225–0.275 ohms at 25°C · 034 / 036; Section 4.2 figure and resistance table
  • 1128 434 5000 — New rear heating element0.9–1.1 ohms at 25°C · 034 / 036; Section 4.2 figure and resistance table

Service note · 034 / 036

034 / 036 new flywheel retrofit requires both new heaters

Up to X 31 813 247: replace front handle and bond new rear element.

up to X 31 813 247 — Older heated-handle saw retrofit condition when installing 1208; not a production start or a tank-system cutoff.

  • Heated-handle saws UP TO machine number X 31 813 247: if installing new flywheel 1125 400 1208, rear heating element 1128 434 5000 MUST BE BONDED into the rear handle and front handle 1125 790 1702 MUST REPLACE the original. This is a paired replacement requirement, not an optional choice of one heater.
  • Original front handle 1125 790 1707 and original rear element 1125 434 5000 may ONLY be fitted to saws equipped with flywheel 1125 400 1207. Their continued spare supply for older machines does not authorize use with 1208.
  • The TI warns that a machine with EITHER old front 1707 OR old rear element 1125 434 5000 AND new flywheel 1208 must not run at full throttle for more than ABOUT 4 MINUTES because heating elements might burn out. This warning does NOT override the required replacement or authorize a four-minute mismatch test; no safe operating duration is established.
  • Summary: flywheel 1207→1208 original no longer factory available; front 1707→1702 and rear 1125 434 5000→1128 434 5000 originals retained for older machines. Introduction IN PROGRESS. The up-to serial is a retrofit condition, NOT proof of a universal production start at the next serial; do not use it to resolve the separate tank-vent/filler-cap cutoff conflict.
  • No adhesive, bonding preparation, cure time or complete heater-installation procedure is specified. Footer June 21, 1995, D1/MTK-al; prior TI 12/1994 is bibliographic. Neither supplies missing installation parameters.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 4 · TI 28/1995, p. 5 — Section 4 service notes, complete summary/remarks and footer.

Part numbers (6)
  • 1125 400 1207 — Original flywheelrequired with original heaters · 034 / 036; Section 4 service notes, complete summary/remarks and footer
  • 1125 400 1208 — New flywheelrequires new heaters on stated older saws · 034 / 036; Section 4 service notes, complete summary/remarks and footer
  • 1125 790 1707 — Original front handleold flywheel only · 034 / 036; Section 4 service notes, complete summary/remarks and footer
  • 1125 790 1702 — New front handlerequired replacement · 034 / 036; Section 4 service notes, complete summary/remarks and footer
  • 1125 434 5000 — Original rear elementold flywheel only · 034 / 036; Section 4 service notes, complete summary/remarks and footer
  • 1128 434 5000 — New rear elementmust be bonded · 034 / 036; Section 4 service notes, complete summary/remarks and footer

Wrong number or missing part for the 034? Report a correction →