← 034 · 036 · MS 340/360

Stihl 1125 · Section B · 2 of 17 · 18 parts

Cylinder

Fits 036.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516234455667777889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (18)

PosPart numberDescriptionQty
1 9512 003 2340 Needle cage 10x14x13 1
2 1125 020 1215 Cylinder with piston Ø 48 mm — 61.5 cc 1
3 1125 020 1206 Cylinder with piston Ø 48 mm → replaced by 1125 020 1215 TI 55/2002 — 61.5 cc 1
4 1125 030 2001 Piston Ø 48 mm — 61.5 cc 1
5 1125 034 3001 Piston ring Ø 48x1.2 mm — 61.5 cc 2
6 1125 034 1500 Piston pin 10x6x32 1
7 9463 650 1000 Snap ring 10 2
8 0000 953 0818 Stud M5 2
9 1122 025 2200 Plug Fitment / change note → 1
10 1121 084 7100 Cap 1
11 1128 020 9400 Decompression valve Fitment / change note → 1
12 1122 084 1405 Cover Fitment / change note → 1
13 1119 029 2301 Cylinder gasket 0.5 mm 1
14 1125 029 2301 NLA Cylinder gasket 1 mm 1
15 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
16 1110 400 7005 Spark plug Bosch WSR 6 F 1
16 0000 400 7000 Spark plug NGK BPMR7A 1
Not numbered on the diagram — assemblies, kits and options
— 1125 007 1050 NLA Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 036

036 decompression valve: operation and cylinder change

Factory introduction from X 32 622 640; ignition pressure closes the manually opened valve.

  • From machine number X 32 622 640, model 036 gains decompression valve 1128 020 9400 and the new air filter system. Cylinder with piston 1125 020 1213 becomes 1125 020 1216; the new cylinder supply includes plug 1122 025 2200. The valve is a separate summary row, not listed as included in the cylinder supply. Original cylinder remains factory supplied only while stocks last; all other parts as before.
  • The complete valve screws into the cylinder. Body (1), axially moving conical plunger (2) and three spring-loaded balls (3), spaced 120 degrees apart, retain upper/lower positions. Pressing the plunger DOWN manually opens the bore before starting. Some compressed mixture escapes through the arrowed bore during cranking, reducing starter effort; remaining pressure is below closing pressure. After IGNITION, pressure exceeds closing pressure, pushes the plunger UP and closes the bore.
  • No numeric closing-pressure threshold, valve rebuild procedure or permission to run a test is supplied. Later cylinder sheet B lists 1125 020 1215/1206, not TI 1213/1216; that difference does not establish a supersession or extend these changes to MS 360.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 1 · TI 30/1995, p. 2 · TI 30/1995, p. 3 — Sections 1 and 1.1, valve cutaways and cylinder summary.

Part numbers (4)
  • 1125 020 1213 — Original cylinder with pistonstocks-only original · 036; Sections 1 and 1.1, valve cutaways and cylinder summary
  • 1125 020 1216 — New cylinder with pistonincludes plug · 036; Sections 1 and 1.1, valve cutaways and cylinder summary
  • 1122 025 2200 — Plugincluded with new cylinder · 036; Sections 1 and 1.1, valve cutaways and cylinder summary
  • 1128 020 9400 — Decompression valveseparate new component · 036; Sections 1 and 1.1, valve cutaways and cylinder summary

Service note · 036

036 replacement shroud: seal the opening on saws without a valve

Raised valve guard, dust cover and blanking cap have different functions.

  • Shroud 1125 080 1612 becomes 1125 080 1614, including cap 1122 084 7100. The opening has a raised area to protect the valve from accidental contact. Cover 1122 084 1405 fits BETWEEN CYLINDER AND SHROUD to reduce dust entry; it is not the blanking cap.
  • When the new replacement shroud is fitted to a machine WITHOUT A DECOMPRESSION VALVE, the opening MUST BE SEALED with the provided cap 1122 084 7100. This does not authorize drilling a cylinder or adding a valve to every old saw.
  • SUPPLY WORDING DIFFERENCE: prose says ONLY THE NEW SHROUD is available as a replacement; summary remark 1 says original shroud supplied only while existing stocks last. Retain both, without inventing the stock-exhaustion date. Factory change X 32 622 640. Later sheet O lists shrouds 1125 080 1620/1617, not the TI 1612/1614 pair; no replacement chain inferred.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 2 · TI 30/1995, p. 3 — Section 1.1 shroud figures and summary.

Part numbers (4)
  • 1125 080 1612 — Original shroudstocks-only summary; prose says new only · 036; Section 1.1 shroud figures and summary
  • 1125 080 1614 — New shroudincludes blanking cap · 036; Section 1.1 shroud figures and summary
  • 1122 084 7100 — Blanking caprequired when no decompression valve · 036; Section 1.1 shroud figures and summary
  • 1122 084 1405 — Dust coverbetween cylinder and shroud · 036; Section 1.1 shroud figures and summary

Service note · 036

036 locking strip: remove the decompression valve first

Valve removal is required before piston blocking; pressure testing also uses a plug.

  • The decompression valve MUST BE REMOVED BEFORE fitting the locking strip to block the piston and carrying out repairs. This is the 036 instruction printed in TI30; do NOT replace it with the CLOSED-valve instruction for 021/023/025 in TI29/1995. No locking-strip ordering number is printed here.
  • Valve removal/installation uses a standard commercial deep-well 13-mm socket. Valve tightening torque 14 Nm (10.3 lbf.ft). For the engine pressure test the TI RECOMMENDS removing the valve and sealing its tapped hole with plug 1122 025 2200.
  • No separate plug torque, test pressure, duration, piston position or complete engine-blocking procedure is specified. These preparation requirements are not a complete repair procedure or hardware authorization.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 3 — Section 1.1 service note and Important warning.

Part numbers (2)
  • 1128 020 9400 — Decompression valveremove before locking strip · 036; Section 1.1 service note and Important warning
  • 1122 025 2200 — Plugrecommended for engine pressure test · 036; Section 1.1 service note and Important warning

Wrong number or missing part for the 036? Report a correction →