← 034 · 036 · MS 340/360

Stihl 1125 · Section C · 3 of 17 · 14 parts

Muffler

Fits 036.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101112132344567899
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (14)

PosPart numberDescriptionQty
1 1125 141 3200 Cooling plate 1
2 1125 149 0601 Muffler gasket 1
3 1125 140 0607 Muffler → replaced by 1125 140 0611 TI 35/2001 1
4 1125 145 0804 Exhaust casing 1
5 9022 341 0910 Spline screw IS-M5x6 2
6 9022 341 0980 Spline screw IS-M5x16 2
7 9022 341 1050 Spline screw IS-M5x25 Fitment / change note → 2
8 1125 140 0609 Muffler Fitment / change note → 1
9 1125 145 0805 Exhaust casing Fitment / change note → 1
10 1125 141 9001 Screen Fitment / change note → 1
11 1125 140 0614 Muffler Fitment / change note → 1
12 1125 149 0500 Gasket Fitment / change note → 1
13 1125 140 0611 Muffler 1
Not numbered on the diagram — assemblies, kits and options
— 1125 007 1050 NLA Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 034 / 036

034 / 036 USA muffler: exhaust bore reduces to 11 mm

0609 replaces 0608; unchanged upper casing and screen; lower casing not separate.

  • USA ONLY, versions with spark-arresting screen: muffler 1125 140 0608 with 16 mm (0.63 inch) exhaust bore is replaced by 1125 140 0609 with 11 mm (0.43 inch) bore to standardize parts. This is replacement of a muffler, not an instruction to drill, sleeve or modify a bore.
  • Muffler item 1 includes items 2–4: upper casing 1125 145 0805 and screen 1125 141 9001 retain their numbers; lower casing has -*-, NO ORDERING NUMBER, and remark 2 says NOT AVAILABLE AS A SEPARATE ITEM. Do not substitute a later inlet-casing number for this source-only row.
  • Original muffler no longer factory available; introduction IN PROGRESS with no numeric cutoff. All other parts as before. Later 034 C and 036 C key 8 list 0609, key 9 upper/exhaust casing 0805 and key 10 screen 9001; their other muffler variants do not extend the USA-only rule.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 3 — Section 2 USA-only muffler and summary items 1–4.

Part numbers (4)
  • 1125 140 0608 — USA muffler, 16-mm exhaust borereplaced; no longer factory available · 034 / 036; Section 2 USA-only muffler and summary items 1–4
  • 1125 140 0609 — USA muffler, 11-mm exhaust borereplacement · 034 / 036; Section 2 USA-only muffler and summary items 1–4
  • 1125 145 0805 — Upper casingunchanged item 2 · 034 / 036; Section 2 USA-only muffler and summary items 1–4
  • 1125 141 9001 — Spark-arresting screenunchanged item 3 · 034 / 036; Section 2 USA-only muffler and summary items 1–4

Conditional replacement · 036

036 EPA muffler: restricted replacement and longer mounting screws

Keep the original muffler for older machines; linkage retrofit permission does not apply.

  • New muffler 1125 140 0614 has a SMALLER exhaust opening and may ONLY be used for EPA-approved machines. Original muffler 1125 140 0609 remains available as a spare and should still be used in older machines. This is not a universal supersession.
  • Gasket 1125 149 0500 sits BETWEEN UPPER AND LOWER muffler casings, not at an inferred cylinder flange. Two crankcase mounting screws change from IS-M5x20 (9022 371 1020) to IS-M5x25 (9022 341 1050). Original screw remains available as a spare FOR OTHER MODELS (remark 7). No mounting torque or interchange of screw specifications is supplied.
  • Introduction is in progress, without a numerical serial threshold. The footer names TI33/1997 as the last TI on 036; this is bibliography, not additional restrictions imported from that bulletin. Later 036 muffler sheet is navigation context, not evidence that every listed muffler is interchangeable.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 5 · TI 43/1997, p. 6 — Section5; drawing138TI026 KN; summary items14–16 and remarks1/7.

Part numbers (5)
  • 1125 140 0609 — Original mufflerRetained for older machines · 036; Section5; drawing138TI026 KN; summary items14–16 and remarks1/7
  • 1125 140 0614 — New small-outlet mufflerEPA-approved machines only · 036; Section5; drawing138TI026 KN; summary items14–16 and remarks1/7
  • 1125 149 0500 — Muffler casing gasketBetween upper/lower casings · 036; Section5; drawing138TI026 KN; summary items14–16 and remarks1/7
  • 9022 371 1020 — Original IS-M5x20 spline screw,2xSpare for other models · 036; Section5; drawing138TI026 KN; summary items14–16 and remarks1/7
  • 9022 341 1050 — New IS-M5x25 spline screw,2xCrankcase mounting · 036; Section5; drawing138TI026 KN; summary items14–16 and remarks1/7

Wrong number or missing part for the 036? Report a correction →