Stihl 1125 · Section D · 4 of 17 · 36 parts
Oil pump, Chain tensioner kit
Fits 036.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1125 640 3001 | Pump housing | 1 |
| 2 | not sold separately | Oil hose 74 mm / 2.9'' not available as a separate item | 1 |
| 3 | 0000 997 0629 | Compression spring | 1 |
| 4 | 1125 647 0602 | Pump piston | 1 |
| 5 | 0000 958 0611 | Washer | 2 |
| 6 | 1125 647 7002 | Plug | 1 |
| 7 | 1128 647 4806 | Control bolt | 1 |
| 8 | 9380 620 1090 | Roll pin 2x10 | 1 |
| 9 | 9646 945 0160 | O-ring 4x2 | 2 |
| 10 | 9022 313 0660 | Spline screw IS-M4x12 | 2 |
| 11 | 1125 647 7800 | Washer | 1 |
| 12 | 1125 640 7110 | Worm | 1 |
| 13 | 1125 647 2400 | Spring | 1 |
| 14 | 0000 993 0510 | Ring | 1 |
| 15 | 0000 953 6605 | Collar screw M8 | 2 |
| 16 | 1125 664 1400 | Thrust pad | 1 |
| 17 | 1125 640 1900 | Tensioner slide | 1 |
| 18 | not sold separately | Spur gear not available as a separate item | 1 |
| 19 | not sold separately | Adjusting screw not available as a separate item | 1 |
| 20 | 9646 945 0490 | O-ring 7x1.5 | 1 |
| 21 | 1122 664 2200 | Cover plate | 1 |
| 22 | 9041 216 0630 | Pan head screw M4x8 Fitment / change note → | 2 |
| 23 | 1122 664 4500 | Support | 1 |
| 24 | 1122 664 1000 | Inner side plate 0.5 mm Fitment / change note → | 1 |
| 25 | 1122 664 1001 NLA | Inner side plate Fitment / change note → option | 1 |
| 26 | 1125 640 1701 | Chain sprocket cover Fitment / change note → → replaced by 1122 640 1702, 1128 640 1706 TI 36/2000 | 1 |
| 27 | 1121 648 6610 | Bumper strip | 2 |
| 28 | 1125 656 1501 | Guard | 1 |
| 29 | 0000 955 0801 | Hexagon nut M8 | 2 |
| 30 | 1110 664 0501 | Bumper spike | 1 |
| 30 | 1128 664 0500 | Bumper spike | 1 |
| 31 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 2 |
| 32 | 9214 320 0700 | Lock nut M5 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1125 640 3201 | Oil pump | 1 |
| — | 1124 007 1010 | Oil hose kit | 1 |
| — | 1125 007 1021 | Spur gear / chain adjusting screw kit | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 024 / 026 / 034 / 036
024 / 026 / 034 / 036: sprung side plate requires the revised cover
Side plate 1122 664 1000 changes to 1122 664 1001; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.
- When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
- Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
- The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
- The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
- For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
- Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
- Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
- Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.
Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.
Part numbers (7)
- 1122 664 1000 — Original side platePrevious version · Retained for original cover
- 1122 664 1001 — Sprung-tab side plateNew version · Requires new-version cover
- 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
- 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
- 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
- 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
- 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
Wrong number or missing part for the 036? Report a correction →