← 034 · 036 · MS 340/360

Stihl 1125 · Section M · 12 of 17 · 45 parts

Carburetor C3A-S39B, C3A-S52

Fits 036.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252627293303132333434343435353637383944041424356789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (45)

PosPart numberDescriptionQty
1 1120 122 7800 Oval head screw 1
2 1125 121 0802 End cover 1
3 1125 121 0804 End cover 1
4 1128 122 7700 Oval head screw 1
5 1128 122 1502 Washer 1
6 1128 122 9301 Clip 1
7 1125 430 0500 Switch 1
8 1128 122 1501 Washer 1
9 1125 121 0807 End cover 1
10 1125 121 0805 End cover 1
11 1125 129 0900 Gasket 1
12 1128 121 4802 Pump diaphragm Fitment / change note → 1
13 1123 121 7800 Strainer 1
14 1125 121 5408 Valve jet 0.58 1
15 1123 121 0700 Cup plug 1
16 4116 121 5100 Inlet needle 1
17 1120 122 3004 Spring 1
18 1125 121 5000 Inlet control lever 1
19 1120 121 9200 Spindle 1
20 1120 122 6600 Collar screw 1
21 1125 129 0901 Gasket 1
22 1125 121 4700 Metering diaphragm 1
23 1120 122 6601 Collar screw 4
24 1125 122 4200 Clamp 1
25 1125 121 3301 Throttle shutter 1
26 1125 122 7402 Round head screw 1
27 1125 122 3202 Torsion spring 1
29 1125 122 9001 E-clip 1
30 1125 122 3203 Torsion spring 1
31 1125 120 7201 Choke shaft with lever 1
32 1125 122 9003 E-clip 1
33 1125 122 4600 Support Fitment / change note → 1
34 4135 121 8600 Washer Fitment / change note → 4
35 1125 122 3000 Spring Fitment / change note → 2
36 1125 122 6803 Low speed adjustment screw Fitment / change note → 1
37 1125 121 2701 Cap Fitment / change note → 1
38 1125 122 6703 High speed adjustment screw Fitment / change note → 1
39 1125 121 2700 Cap Fitment / change note → 1
40 1125 122 6200 Idle speed adjustment screw 1
41 1125 121 2901 Choke shutter 1
42 1125 122 7403 Round head screw 1
43 1125 121 5409 Valve jet 0.56 option 1
Not numbered on the diagram — assemblies, kits and options
— 1125 120 0615 Carburetor C3A-S39B Fitment / change note → 1
— 1125 120 0612 Carburetor C3-S52 1
— 1128 007 1065 Set of carburetor parts Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 034S / 036 / 044

034S / 036 / 044: pump diaphragm changes inside the same kit

Pump diaphragm 1125 121 4802 changes to 1128 121 4802; carburetor parts kit 1128 007 1065 keeps its number while its contents change.

  • The new pump diaphragm uses a different material; the source does not identify that material or quantify compatibility with fuel blends.
  • The kit summary explicitly names 034S, 036 and 044 and includes item1 (pump diaphragm). The unmodified kit is supplied until existing stocks are exhausted, so kit number alone does not identify the installed diaphragm.
  • The old diaphragm is no longer factory supplied per remark1; this differs from the retained spare status of the valve jet, screws and shafts.
  • 034S is named by the source but has no exact-model catalog sheet bound here. Do not extend it to ordinary034,036QS,MS360 or other successor/variant sheets. The linked036 sheets contain this kit; the044 production serial is not a036/034S serial boundary.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 3 · TI 16/1994, p. 4 — Sections2.1 and2.3, pump diaphragm and kit row.

Part numbers (3)
  • 1125 121 4802 — Original pump diaphragmHistorical version · Named kit configurations
  • 1128 121 4802 — Revised-material pump diaphragmHistorical version · Named kit configurations
  • 1128 007 1065 — Carburetor parts kitUnchanged number; changed contents · 034S / 036 / 044 as printed

Conditional replacement · 036

036: EPA-only C3A-S39A carburetor introduction

C3A-S31A remains a spare; the new carburetor is restricted to EPA-approved machines.

  • The cover identifies STIHL 036, series 1125. The factory applies the illustrated engine-information label to machines meeting the latest standard described here. Its blank engine-family/type/displacement/manufacture fields are an example, not actual machine identifiers or a serial changeover. Modification introduction is IN PROGRESS; no numeric cutoff is printed.
  • Page 1 calls the old/new types C3A-S31 and C3A-S39; page 6 calls them C3A-S31A and C3A-S39A. Preserve the suffix difference rather than equating every revision. Original 1125 120 0651 is replaced in this EPA configuration by 1125 120 0615; each complete assembly includes summary items 1–8. Original complete carburetor remains available as a spare (remark 1); the new assembly MUST be used for EPA-approved machines ONLY (remark 2). This is not an unrestricted retrofit.
  • New H and L screws carry limiter caps restricting adjustment. All other carburetor parts remain as before. Linked later IPL C3A-S39B/C3A-S52 uses 0615 for S39B: navigation only, not proof S39A, S39B and S52 have identical calibration or settings. TI27/1997 is delegated for EPA detail and remains a named source gap.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 1 · TI 43/1997, p. 6 — Cover; section1; summary complete carburetors, inclusion range and remarks1/2.

Part numbers (2)
  • 1125 120 0651 — Original carburetor C3A-S31 / C3A-S31ARemains available as spare · 036; Cover; section1; summary complete carburetors, inclusion range and remarks1/2
  • 1125 120 0615 — New carburetor C3A-S39 / C3A-S39AEPA-approved machines only · 036; Cover; section1; summary complete carburetors, inclusion range and remarks1/2

Service note · 036

036 EPA carburetor: complete revised internal-parts roster

Keep original spares separate and do not reuse drawing numbers as summary positions.

  • H and L screws have sealing rings and knurled heads holding the caps; red cap limits H and white cap limits L. Springs retain preset screw positions; holder guides caps. Page 1 drawing/list uses holder 6 and washers 7; page 6 SUMMARY instead uses washer 6 and holder 7. These are separate source numbering contexts, not interchangeable IPL positions.
  • Summary changes: H screw 1125 122 6702 to 1125 122 6703; L screw 1125 122 6802 to 1125 122 6803; spring (2x) 1120 122 3005 to 1125 122 3000; valve jet 1125 121 5404 to 1125 121 5405. These original components remain spare parts (remark 1). No individual-component universal retrofit or calibration equivalence is stated.
  • New red cap 1125 121 2700, white cap 1125 121 2701, washers 4135 121 8600 (4x) and holder 1125 122 4600 have no original-number entry. Both complete-carburetor rows say they include items 1–8, but dashes in original columns do not establish that the old assembly had the newly listed caps, washers or holder. All other carburetor parts remain as before. Later S39B/S52 sheet is discovery context only.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 1 · TI 43/1997, p. 6 — Section1.1 and drawing138TI017 KN; summary items1–8 and remark1.

Part numbers (12)
  • 1125 122 6702 — Original H screwOriginal spare · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 122 6703 — New H screw with sealing ringRevised · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 122 6802 — Original L screwOriginal spare · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 122 6803 — New L screw with sealing ringRevised · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 121 2700 — Red H limiter capNew · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 121 2701 — White L limiter capNew · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1120 122 3005 — Original spring,2xOriginal spare · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 122 3000 — New spring,2xRevised · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 4135 121 8600 — Washers,4xSummary item6; drawing item7 · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 122 4600 — HolderSummary item7; drawing item6 · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 121 5404 — Original valve jetOriginal spare · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1
  • 1125 121 5405 — New valve jetRevised · 036; Section1.1 and drawing138TI017 KN; summary items1–8 and remark1

Service note · 036

036 C3A-S39: capped standard setting and altitude correction

H 3/4 and L 1/4 turn are measured from the lean stop, not screw seats.

  • Factory optimum setting with caps fitted is stated to equal the owner-manual standard: H=3/4 turn open and L=1/4 turn open, starting from the LEAN STOP in each case. Two cap stops limit correction to 270 degrees. This is not the uncapped basic setting and not a later S39B/S52 calibration instruction.
  • For unsatisfactory running at higher altitude, the source allows slight correction: check standard setting, warm engine, turn H and L clockwise (leaner), within cap limits. The source warns an excessively lean setting exceeds maximum permissible speed and risks engine damage. No numerical maximum engine speed is provided here; do not invent one or remove caps for ordinary altitude correction.
  • The cap range is described as permitting altitude correction while helping prevent enrichment beyond EPA emission limits. This historical statement is not current legal compliance certification. The owner-manual chapter is referenced only for the explicitly reproduced standard setting; the full owner manual is not claimed reviewed.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 2 — Section1.2; drawings138TI021/018/019 KN.

No additional parts-table entry added.

Service note · 036

036 limiter-cap repair: new caps, L first, separate basic setting

Removed caps are damaged; uncapped H and L each open one full turn from their seats.

  • To replace adjusting screws or clean the carburetor, the source removes H/L caps with suitable pliers. Caps are damaged during disassembly and MUST NOT be reused. Fit NEW caps after the specified repair adjustment; this is repair guidance, not permission for routine cap-free operation.
  • After fitting adjusting screws, the uncapped BASIC setting starts with screws against their seats: H open 1 full turn and L open 1 full turn. Do not substitute the capped lean-stop reference or infer a tightening torque.
  • Fit the LOW-SPEED cap FIRST. Both slots are vertical. Drawing138TI023 KN shows L stop toward the lower right as viewed on the page; drawing138TI024 KN shows H stop toward the lower right at the RICH stop. Preserve the illustrated viewpoint and exact stop positions; do not interpret vertical slots alone as sufficient orientation. Push caps until they snap into position. The TI states the final caps/screws correspond to section 1.2 standard setting.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 3 — Sections1.3,1.3.1,1.3.2; drawings138TI020/022/023/024 KN.

No additional parts-table entry added.

Service note · 036

036 EPA setup: 2,800 rpm idle, 50:1 evidence and TI27 gap

Use a tachometer; other fuel ratios have no emission measurements in this TI.

  • Idle is set to 2,800 rpm with the LA idle-speed screw; USE A TACHOMETER. LA is distinct from H/L mixture screws. This is a source value, not a hardware test or a maximum-speed specification.
  • EPA approval is stated to have been obtained with fuel/oil ratio 50:1. No emission measurements are available for other mix ratios. This does not establish approval for other ratios or prescribe an unprinted oil specification.
  • TI27/1997 is delegated for additional EPA and Federal Emission Control Systems—Utility Engines details. It is absent from the retained690-TI corpus and the previously verified766-resource mapped inventory; that bounded source gap remains. Do not manufacture its regulatory, warranty or maintenance requirements. The full owner manual is not imported by this review.
  • Historical TI43/1997 guidance for the named 036 configuration only, not 034, MS 360 or every 036 variant. Supply remarks describe 1997, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 43/1997, p. 1 · TI 43/1997, p. 4 — Section1.3.3,1.4,1.5 and cover EPA reference.

No additional parts-table entry added.

Wrong number or missing part for the 036? Report a correction →