← 034 · 036 · MS 340/360

Stihl 1125 · Section N · 13 of 17 · 38 parts

Carburetor C3A-S27D

Fits 036.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252627282933031313233343536456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (38)

PosPart numberDescriptionQty
1 1128 122 7700 Oval head screw 1
2 1128 122 1502 Washer Fitment / change note → 1
3 1128 122 9301 Clip Fitment / change note → 1
4 1125 430 0500 Switch Fitment / change note → 1
5 1128 122 1501 Washer Fitment / change note → 1
6 1125 121 0807 End cover 1
7 1125 129 0900 Gasket 1
8 1128 121 4802 Pump diaphragm Fitment / change note → 1
9 1123 121 7800 Strainer 1
10 1125 121 5408 Valve jet 0.58 1
11 1123 121 0700 Cup plug 1
12 4116 121 5100 Inlet needle 1
13 1120 122 3004 Spring 1
14 1125 121 5000 Inlet control lever 1
15 1120 121 9200 Spindle 1
16 1120 122 6600 Collar screw 1
17 1125 129 0901 Gasket 1
18 1125 121 4700 Metering diaphragm 1
19 1125 121 0805 End cover 1
20 1120 122 6601 Collar screw 4
21 1125 122 4200 Clamp 1
22 1125 121 3301 Throttle shutter 1
23 1125 122 7402 Round head screw 1
24 1125 122 3202 Torsion spring 1
25 1125 120 7101 Throttle shaft with lever 1
26 1125 122 9001 E-clip 1
27 1125 122 3203 Torsion spring 1
28 1125 120 7201 Choke shaft with lever 1
29 1125 122 9003 E-clip 1
30 1125 122 6200 Idle speed adjustment screw 1
31 1120 122 3005 Spring 2
32 1125 122 6702 High speed adjustment screw Fitment / change note → 1
33 1125 122 6802 Low speed adjustment screw Fitment / change note → 1
34 1125 121 2901 Choke shutter 1
35 1125 122 7403 Round head screw Fitment / change note → 1
36 1125 121 5409 Valve jet 0.56 option 1
Not numbered on the diagram — assemblies, kits and options
— 1125 120 0609 Carburetor C3A-S27D Fitment / change note → 1
— 1128 007 1065 Set of carburetor parts Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 034S / 036 / 044

034S / 036 / 044: pump diaphragm changes inside the same kit

Pump diaphragm 1125 121 4802 changes to 1128 121 4802; carburetor parts kit 1128 007 1065 keeps its number while its contents change.

  • The new pump diaphragm uses a different material; the source does not identify that material or quantify compatibility with fuel blends.
  • The kit summary explicitly names 034S, 036 and 044 and includes item1 (pump diaphragm). The unmodified kit is supplied until existing stocks are exhausted, so kit number alone does not identify the installed diaphragm.
  • The old diaphragm is no longer factory supplied per remark1; this differs from the retained spare status of the valve jet, screws and shafts.
  • 034S is named by the source but has no exact-model catalog sheet bound here. Do not extend it to ordinary034,036QS,MS360 or other successor/variant sheets. The linked036 sheets contain this kit; the044 production serial is not a036/034S serial boundary.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 3 · TI 16/1994, p. 4 — Sections2.1 and2.3, pump diaphragm and kit row.

Part numbers (3)
  • 1125 121 4802 — Original pump diaphragmHistorical version · Named kit configurations
  • 1128 121 4802 — Revised-material pump diaphragmHistorical version · Named kit configurations
  • 1128 007 1065 — Carburetor parts kitUnchanged number; changed contents · 034S / 036 / 044 as printed

Historical fitment · 036

036: VH carburetor heating and component set

Thermostatic cut-out +7 to +13°C; 8 Ω at +25°C, with a separate heating plate.

  • Section 1 announces one additional 036 version with electric carburetor heating (VH), not a new 034 heating option. Switch (2) is clipped (3) to carburetor end cover (1). Heating element (4) and plate (5) fit BETWEEN carburetor and air filter; these diagram numbers differ from the parts-table items.
  • Thermostatic switch CUT-OUT range +7 to +13°C (45–55°F). Section 1.1.2 gives resistance 8 Ω at +25°C (77°F) beside the heating-element/plate description; it does not define a complete meter test circuit, switch cut-in temperature or tolerance. Do not treat 8 Ω as the closed-switch resistance or a general engine temperature limit.
  • VH carburetor 1125 120 0609 includes table items 2–6: switch, clip, round-head screw and TWO separately numbered washers. Heating element, plate, harness and grommet are table items 7–10, not listed as included in the carburetor. All other parts as on standard carburetor; introduction in progress with NO serial cutoff.
  • Current 036 air-filter/N carburetor sheets identify 0609 as C3A-S27D, whereas this TI labels it only VH. Keep that IPL identity separate; do not infer all C3A-S27D units are already heater-equipped or substitute later C3A-S39B/C3A-S52 assemblies.
  • Historical TI 21/1996 evidence only; no present stock status, calendar introduction date or universal retrofit inferred. No hardware operation was performed.

Source: TI 21/1996, p. 1 · TI 21/1996, p. 4 — VH carburetor heating and component set.

Part numbers (10)
  • 1125 120 0609 — Carburetor (VH), includes items 2–6New complete assembly · 036 VH carburetor-heating version
  • 1125 430 0500 — Thermostatic switchIncluded item 2 · 036 VH carburetor-heating version
  • 1128 122 9301 — ClipIncluded item 3 · 036 VH carburetor-heating version
  • 1125 122 7403 — Round head screwIncluded item 4 · 036 VH carburetor-heating version
  • 1128 122 1502 — WasherIncluded item 5 · 036 VH carburetor-heating version
  • 1128 122 1501 — WasherIncluded item 6 · 036 VH carburetor-heating version
  • 1128 434 5101 — Heating elementSeparate item 7 · 036 VH carburetor-heating version
  • 1125 121 9900 — Heating plateSeparate item 8 · 036 VH carburetor-heating version
  • 1125 440 3000 — Wiring harnessSeparate item 9 · 036 VH carburetor-heating version
  • 1125 123 7500 — GrommetSeparate item 10 · 036 VH carburetor-heating version

Historical fitment · 036

036 VH: modified screws, valve jet and fixed-jet restriction

TI32 extends its calibration changes to 1125 120 0609; no new VH type designation or separate serial is supplied.

  • The service note explicitly extends THESE CHANGES to VH carburetor 1125 120 0609 introduced in TI21/1996. That already reviewed introduction identifies the 036 heating version. Do not extend this statement to an invented 034 VH version or interpret every carburetor on a shared series sheet as heated.
  • The stated changes are sealing rings on H/L screws, valve jet 1125 121 5402 to 1125 121 5404, high-speed screw 1125 122 6701 to 1125 122 6702, low-speed screw 1125 122 6801 to 1125 122 6802, and the nonremovable part-load fixed jet. Original screws and valve jet MUST NOT go into the modified version because of different calibration. The fixed jet can be blown clear with compressed air; no pressure or adjustment setting is given.
  • 1125 120 0609 remains the cited VH assembly. TI32 supplies no new VH type designation or separately identified VH serial cutoff; do not rename it C3A-S31A simply because the standard 0651 changes to that name. The later exact-model IPL calls 0609 C3A-S27D and lists other valve jets. Neither that label nor a shared order number proves the as-found internal revision. Keep the later IPL jet identities separate from the historical 5404 change.
  • Historical TI 32/1996 evidence; not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 32/1996, p. 1 — 036 VH: modified screws, valve jet and fixed-jet restriction.

Part numbers (7)
  • 1125 120 0609 — VH carburetorChanges expressly extended by service note · 036 VH version introduced by TI21/1996
  • 1125 121 5402 — Original valve jetRetained for C3A-S26 · 036 VH; original versus modified calibration per TI32 service note
  • 1125 121 5404 — Modified valve jetNew calibration · 036 VH; original versus modified calibration per TI32 service note
  • 1125 122 6701 — Original high-speed screwRetained for C3A-S26 · 036 VH; original versus modified calibration per TI32 service note
  • 1125 122 6702 — Modified high-speed screwNew sealing-ring design · 036 VH; original versus modified calibration per TI32 service note
  • 1125 122 6801 — Original low-speed screwRetained for C3A-S26 · 036 VH; original versus modified calibration per TI32 service note
  • 1125 122 6802 — Modified low-speed screwNew sealing-ring design · 036 VH; original versus modified calibration per TI32 service note

Service note · 036 / 036 QS

036 / 036 QS: C3A-S27A valve jet and unchanged order number

0.64 mm → 0.60 mm valve jet; earlier source identity conflict remains unresolved.

  • C3A-S27 becomes C3A-S27A while carburetor order number 1125 120 0609 stays unchanged. Each of the two listed carburetor families receives valve jet 1125 121 5404 (diameter 0.60 mm) instead of 1125 121 5403 (diameter 0.64 mm). All other parts remain as before in THIS bulletin; the dashes separate old/new type rows, not missing order numbers.
  • Modification introduction is IN PROGRESS. No machine-number cutoff is printed; do not reuse the earlier TI32/1996 serial as this changeover. Remark 1 says only the modified carburetor version is factory supplied; remark 2 says the original valve jet is no longer factory supplied. These are historical supply statements, not current stock or blanket retrofit approval.
  • SOURCE CONFLICT RETAINED: the already-reviewed TI32/1996 describes 1125 120 0651 as C3A-S26 → C3A-S31A and valve jet 1125 121 5402 → 1125 121 5404, extending its changes to VH assembly 1125 120 0609. TI06/1997 instead prints C3A-S31 → C3A-S31A and 1125 121 5403 → 1125 121 5404. Both accounts are preserved; whether they describe market/version differences or an error is unresolved. Do not silently rewrite either original identity or infer a universal calibration sequence.
  • The header names 036 and 036 QS, series 1125. Applicability remains conditional on the named carburetor, not every carburetor fitted to either saw. No 034, MS360 or other successor applicability is inferred. Later IPL C3A-S27D and C3A-S31E/C3A-S65 labels are discovery context, not proof of identical internal calibration or a substitute for identifying the fitted version.
  • Historical TI06/1997 evidence; dimensions describe the valve jet, not the nonremovable part-load fixed jet in TI32. No adjustment settings, drilling instruction or tested physical interchange are established. No hardware operation was performed.
  • The linked later S27D sheet is explicitly 036. No exact 036 QS S27 sheet is retained here; the TI header is retained without inventing a QS heating variant or linking a different QS carburetor as S27 proof.

Source: TI 6/1997, p. 1 — C3A-S27 to C3A-S27A unchanged-number valve-jet revision.

Referenced bulletin evidence: TI 32/1996, p. 1 — 036: C3A-S26 to C3A-S31A calibration at X 35 047 484.

Part numbers (3)
  • 1125 120 0609 — Carburetor C3A-S27 / C3A-S27AUnchanged assembly number · TI06/1997 C3A-S27/C3A-S27A; identify actual version
  • 1125 121 5403 — Original valve jet, diameter 0.64 mmOriginal version · TI06/1997 C3A-S27/C3A-S27A; identify actual version
  • 1125 121 5404 — Modified valve jet, diameter 0.60 mmNew version · TI06/1997 C3A-S27/C3A-S27A; identify actual version

Wrong number or missing part for the 036? Report a correction →