Stihl 1125 · Section M · 5 of 8 · 15 parts
Throttle control
Fits 036 QS.
Historical fitment & changes (12) — includes parts and conditions not shown on this drawing.
Parts (15)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1125 180 1503 | Throttle trigger | 1 |
| 2 | 1125 182 4505 | Torsion spring | 1 |
| 3 | 9371 470 2640 | Cylindrical pin 5x24 | 1 |
| 4 | 1125 182 1502 | Throttle rod | 1 |
| 5 | 1125 185 2002 | Choke rod | 1 |
| 6 | 1125 442 1601 | Contact spring | 1 |
| 7 | 1125 442 1601 | Contact spring | 1 |
| 8 | 1125 182 0901 | Switch shaft | 1 |
| 9 | 1125 180 1405 | Trigger switch | 1 |
| 10 | 9517 003 0650 | Cylindrical roller 3x25.8 | 2 |
| 11 | 1125 160 2503 | Brake cable | 1 |
| 12 | 9099 021 2770 | Self-tapping screw 3.9x13 | 1 |
| 13 | 1125 180 1703 | Lockout lever | 1 |
| 14 | 1125 791 0602 | Handle molding | 1 |
| 15 | 9074 478 3076 | Pan head self-tapping screw IS-P4x19 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 036 QS
036 QS Quickstop Super: three activation paths and rear-handle reset
Rear-handle release adds a QS braking path; manual and inertia activation remain.
- TI 45/1995 introduces the 036 QS, series 1125. Its cover photograph and introductory claims describe this variant, not a standard 036 conversion kit. The claimed world-first status and enhanced safety are historical manufacturer statements, not independently reproduced findings.
- The throttle-trigger interlock lever also activates the QS system. Pressing it while the engine runs releases the brake band from the clutch drum so the chain CAN rotate; releasing BOTH interlock lever and throttle trigger tightens the band and stops the chain within the source’s qualitative “fractions of a second”. No numerical stopping-time limit is stated.
- Three activation paths remain distinct: front-hand-guard inertia in CERTAIN kickback situations; the user’s hand contacting that guard; and release of the rear-handle interlock lever AND trigger. The two page 2 figures show downward interlock motion to disengage and upward release to engage. They do not promise protection in every kickback.
- After INERTIA OR MANUAL activation, the rear handle (throttle trigger and interlock lever) must be released to RESET the braking system. No additional control is introduced. The source’s “almost all situations” wording for ergonomic activation is not an unconditional guarantee.
- Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.
Source: TI 45/1995, p. 1 · TI 45/1995, p. 2 — 036 QS Quickstop Super: three activation paths and rear-handle reset.
No additional parts-table entry added.
Service note · 036 QS
036 QS brake cleaning: grease arrows differ from clutch-drum oil arrow
Mobilplex 0781 120 1111 at filled arrows; chain oil on clutch-drum outside diameter.
- For improper brake operation, page 4 treats the illustrated sliding/bearing points by contamination level. LIGHT contamination: clean all parts with brush and white spirit. HEAVY contamination or resin clogging: remove affected parts, clean with white spirit or resin solvent, replace worn/damaged parts, and clean machine recesses/seats before reinstallation. No solvent soak duration or substitute chemical is specified.
- In BOTH cases, the FILLED BLACK arrows in figures 148TI003 KN (rear-handle linkage) and 148TI004 KN (brake mechanism) denote Mobilplex 0781 120 1111 grease. The OUTLINED arrow denotes chain lubricant on the OUTSIDE DIAMETER OF THE CLUTCH DRUM. These distinct symbols do not instruct greasing the entire drum or oiling all pivots. The figures are the exact location reference; no unlabelled point is assigned an invented part number.
- Pages 2 and 4 require quality chain lubricant and recommend STIHL Bioplus as the ONLY biological chain oil. The wording does not prohibit all non-biological quality oils. It applies also to sliding/pivot lubrication; unsuitable lubricants may cause resin buildup and premature brake failure. Do not replace the explicit Mobilplex grease arrows with a blanket Bioplus instruction.
- Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.
Source: TI 45/1995, p. 2 · TI 45/1995, p. 4 — 036 QS brake cleaning: grease arrows differ from clutch-drum oil arrow.
Part numbers (1)
- 0781 120 1111 — Mobilplex grease; filled-arrow locationsspecified · 036 QS brake and rear-handle linkage; not clutch-drum oil coating
Service note · 036 QS
036 QS brake checks: interlock release and hand guard are separate tests
With bar and chain fitted, both checks require standstill within fractions of a second.
- Section 1 explicitly says WITH BAR AND CHAIN. In 1.1 the historical check opens the throttle wide, then releases the REAR HANDLE to activate the interlock-linked brake. In 1.2 it separately opens the throttle wide and activates the HAND GUARD. Each requires the chain to come to a standstill within fractions of a second; no numerical stopping-time limit is supplied.
- The printed fault labels are A: brake cannot be activated; B: brake cannot be activated by interlock lever; C: brake cannot be activated by hand guard; D: brake cannot be activated by interlock lever OR hand guard. A and D are retained separately as printed, not silently merged or turned into inferred causes. The extracted body corrupts these letters; the scan is authoritative.
- These are historical test descriptions for trained, authorized personnel, not authorization to run a saw or an unattended full-throttle test. Fault causes and repairs are in later sections, not established by this page alone.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 1 — 036 QS brake checks: interlock release and hand guard are separate tests.
No additional parts-table entry added.
Service note · 036 QS
036 QS interlock travel: less than 6 mm indicates stretched cable
Measure between first definite resistance and the released lever position.
- Figure 1: press down the interlock lever until DEFINITE RESISTANCE is felt and mark l1. Let go of the interlock lever and mark l2. If the distance between l1 and l2 is LESS THAN 6 mm (0.24 inches), the source identifies the brake cable as stretched.
- This is free travel between the two marked positions, not cable overall length, brake-band clearance or a lever force measurement. The inequality is strictly less than, not less than or equal to. A reading of 6 mm or more is not by itself proof the whole brake works.
- No cable adjustment, replacement part number, production serial cutoff or numerical operating force is specified in this section. Diagram leader arrows show the two lever positions; they are not a new wear dimension.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 1 — 036 QS interlock travel: less than 6 mm indicates stretched cable.
No additional parts-table entry added.
Service note · 036 QS
036 QS interlock disassembly: three different punch sizes
3.0 mm roller, 4.5 mm bushing and 4.0 mm trip-lever roller are distinct.
- Figures 2–4: remove carburetor box cover and air filter, remove self-tapping screw (1) from tank housing, and lift handle molding (2). A 3.0 mm (0.12 inch) pin punch drives needle roller (4) out of interlock lever (3). A 4.5 mm (0.18 inch) pin punch drives bushing (5) out of that lever; remove torsion spring (6).
- Figures 5–6 continue on page 2: disconnect brake cable (7) from trip lever (8); use a 4.0 mm (0.16 inch) pin punch to drive needle roller (9) out of the trip lever, then remove the trip lever. Do not use the bushing punch diameter for either roller.
- The page 2 note requires cleaning all parts with STIHL universal cleaner and replacing damaged parts. Its asterisk requires ORIGINAL STIHL replacement parts according to the latest parts list. The TI gives figure callouts here, not orderable numbers; none are inferred from the later IPL.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 1 · TI 1/1996, p. 2 — 036 QS interlock disassembly: three different punch sizes.
No additional parts-table entry added.
Service note · 036 QS
036 QS assembly begins with lubrication and interlock pivots
Page 4 begins assembly; continuation on pages 5–7 and maintenance arrows are separate source references.
- Section 3 requires lubricating ALL MOVING PARTS with oil or grease and refers to arrows in illustrations under section 4 (page 7). Page 7 distinguishes solid grease arrows from hollow chain-oil arrows; see the separate lubrication note. No additional lubrication point is invented from page 4.
- Section 3.1, figure 25 drives needle roller (9) into trip lever (8). Figure 26 pushes bushing (5) through ONE SIDE of interlock lever (3) and torsion spring (6), then drives it into the interlock lever. These callouts refer back to the interlock section, not the oil-pump linkage alongside it.
- Page 4 ends at an intermediate assembly state. Spring seating, cable installation and assembly continuation are on pages 5–7; the separate operating checks and troubleshooting chart must also be consulted. This note alone does not imply the saw is assembled or serviceable.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 4 — 036 QS assembly begins with lubrication and interlock pivots.
No additional parts-table entry added.
Service note · 036 QS
036 QS interlock reassembly: spring end must seat in trip-lever groove
The right-hand spring end is a specific locating condition, not an optional orientation.
- Figure 27 continues figures25–26: drive needle roller (4) into interlock lever (3); the RIGHT-HAND END OF THE SPRING MUST LOCATE IN THE TRIP LEVER GROOVE. Figure28 positions brake cable (7) in trip lever (8).
- The repeated figure2 then fits handle molding (2), secures it to tank housing with self-tapping screw (1), and installs the air filter. Page5 does not separately state a carburetor-box-cover fastening torque or introduce a new screw number. These are source figure callouts, not IPL positions.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 4 · TI 1/1996, p. 5 — 036 QS interlock reassembly: spring end must seat in trip-lever groove.
No additional parts-table entry added.
Service note · 036 QS
036 QS lubrication: solid grease arrows and hollow chain-oil arrows differ
Mobilplex 0781 120 1111 at marked joints; chain oil on the outside diameter of the clutch drum.
- Section4 figure33 shows the exposed chain-brake linkage and two DIFFERENT arrow styles. SOLID arrows mean grease with Mobilplex 0781 120 1111 at the depicted moving contact/pivot points; HOLLOW arrows mean lubricate with CHAIN OIL on the OUTSIDE DIAMETER OF THE CLUTCH DRUM. The original figure locates the individual points; do not blanket-coat every surface or substitute grease for the specified chain oil.
- Figure34 separately shows the rear-handle/interlock pivots and contacts with SOLID arrows, also specifying Mobilplex 0781 120 1111. Section3 on page4 requires lubricating all moving parts and explicitly directs the reader to these maintenance arrows.
- The page7 footnote says owners wishing to run BIOLOGICAL chain oil should use ONLY STIHL Bioplus. This historical restriction is retained; no current product equivalence, alternative lubricant approval, quantity or interval is inferred. The clutch drum OUTSIDE diameter instruction is printed source guidance for this historical QS mechanism, not general advice for other brakes.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 4 · TI 1/1996, p. 7 — 036 QS lubrication: solid grease arrows and hollow chain-oil arrows differ.
Part numbers (1)
- 0781 120 1111 — Mobilplex grease; historical specified productspecified · 036 QS; historical maintenance guidance only
Service note · 036 QS
036 QS fault A: cable travel, pitch contamination and tension-lever rivet play
Four distinct cause/remedy rows; greater than 0.5 mm play is not the cable-travel limit.
- Fault A is printed BRAKE CANNOT BE ACTIVATED. Row1: free travel <6 mm (0.24 inches), cable stretched → REPLACE BRAKE CABLE. Printed disassembly figures: 1,2,5,7,8,9,10,11,12,13,19; assembly: 33,19,13,12,11,9,10,8,7,34,28,2. Figure33/34 are maintenance references, not unrelated part numbers.
- Row2: all moving parts on oil-pump housing smeared with PITCH → disassemble, clean and service oil-pump housing (section4). Disassembly: 7–14,16,19,20,21,22,23,24; assembly: 33,24,23,29,30,20,19,32,14,13,12,11,9,10,8,7. Pitch here is contamination, not saw-chain pitch.
- Row3: rivet on tension lever worn, PLAY >0.5 mm → FIT NEW TENSION LEVER. The inequality is strictly greater than, not greater than or equal to. Disassembly: 7–14,16,19,20; assembly: 33,20,19,14,32,13,12,11,9,10,8,7. No drilling, rivet repair or adjustment is prescribed.
- Row4: pitch between INSIDE OF COVER AND CLUTCH DRUM → disassemble, clean and service cover and clutch drum (section4). Disassembly: 7–13; assembly: 33,13,12,11,9,10,8,7. Do not merge this contamination location with oil-pump linkage contamination or treat any one row as an exhaustive diagnosis.
- Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.
Source: TI 1/1996, p. 1 · TI 1/1996, p. 7 · TI 1/1996, p. 8 — 036 QS fault A: cable travel, pitch contamination and tension-lever rivet play.
No additional parts-table entry added.
Service note · 036 QS
036 QS only: modified throttle trigger retains its roller
Use the revised1125 180 1501 trigger for repairs; it includes washer0000 958 0407.
- 036 QS ONLY. Throttle trigger1125 180 1501 gains washer0000 958 0407 to hold the roller in position. Drawing148TI005 KN points at the washer on the roller, not a different trigger variant or a separate fastener torque.
- The new version of the throttle trigger should ALWAYS BE INSTALLED IN THE CASE OF A REPAIR. Trigger number1501 stays unchanged; includes item2 washer. Factory supplies only modified version (remark1). Introduction is IN PROGRESS; do not apply the036 carburetor cutoff from page1.
- The exact036 QS throttle-control sheet later lists1125 180 1503 rather than1501 and does not list0407. Link the historical note to the named-model subsystem without declaring1503 equivalent or inventing a supersession. This TI does not give a washer-only retrofit instruction, roller dimension, brake adjustment or full disassembly procedure. Footer TI32.96/06.97 and document6119 are bibliographic context.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 33/1997, p. 2 — Complete section2, drawing, both summary rows, supply/introduction and footer.
Part numbers (2)
- 1125 180 1501 — Throttle trigger including washerSame number; modified-only factory supply · Only the exact model/configuration and restrictions of 1997-33
- 0000 958 0407 — Washer retaining rollerNew item2 · Only the exact model/configuration and restrictions of 1997-33
Service note · 036 QS
036 QS: separate rear-handle brake and three activation paths
Releasing the rear handle stops the chain in less than one second; Quickstop remains distinct.
- The additional REAR HANDLE BRAKE is described as a SEPARATE SYSTEM. Its activation mechanism is integrated in the throttle-trigger interlock: release of the rear handle automatically locks the chain; pressing the interlock releases it so the throttle can be operated. The two page2 figures explicitly assume QUICKSTOP DISENGAGED. Pressing the interlock is not presented as releasing an engaged front-hand-guard brake.
- Three braking paths: front-hand-guard inertia in certain sufficiently severe kickback situations; manually pushing the front hand guard toward the bar nose; and manual release of the rear handle. Quickstop stopping is described as within a fraction of a second; the rear-handle brake limit is LESS THAN ONE SECOND. Do not combine these timings, infer protection in every kickback or backdate the numeric limit to earlier QS TIs.
- Before first operation, the source requires familiarity with this system, especially the owner manual chapters Chain Brake and Starting. Exact 036 QS owner-manual chapters remain a documented source gap. The available 1999-10 034/036/036 QS SERVICE manual is not that owner manual. No starting sequence is invented here.
- Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.
Source: TI 5/1999, p. 1 · TI 5/1999, p. 2 — Complete section 1.1 and operation figures 148TI000/006 KN,including warning.
No additional parts-table entry added.
Service note · 036 QS
036 QS: solid grease arrows differ from hollow chain-oil arrows
Mobilplex 0781 120 1111 goes on marked joints; chain lubricant coats the clutch-drum circumference.
- If brake function is improper: SLIGHT contamination calls for a suitable brush and mineral spirit to clean all parts. HEAVY contamination or resin clogging calls for disassembling the parts, cleaning with mineral spirit or resin solvent, replacing worn/damaged parts, and cleaning housing recesses before reinstallation. No chemical substitution, soaking time or unsourced disassembly sequence is given.
- In BOTH cleaning cases, SOLID black arrows in figures 148TI007 KN (rear handle) and 148TI008 KN (brake mechanism) mean Mobilplex 0781 120 1111 grease. HOLLOW arrows mean CHAIN LUBRICANT on the CIRCUMFERENCE OF THE CLUTCH DRUM. Original figures locate the points; no arrow is assigned an invented component number. Do not grease the whole drum, replace grease with oil at every pivot, or generalize this historical QS instruction to other chain brakes.
- Quality chain lubricant is required. If a biological lubricant is preferred, TI05 RECOMMENDS STIHL Bioplus; the recommendation also applies to the moving-system maintenance. Unsuitable oils can produce resin buildup and premature brake failure. The footnote requires original STIHL replacement parts from the current parts list.
- Wording difference retained: TI01/1996 says use ONLY STIHL Bioplus for biological oil, while TI05/1999 says RECOMMEND. This note preserves each dated statement without inventing a current substitute approval or silently rewriting the earlier restriction.
- Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.
Source: TI 5/1999, p. 2 · TI 5/1999, p. 3 — Chain Lubrication and complete service cleaning branches,figures 148TI007/008 KN,legend and starred footnote.
Referenced bulletin evidence: TI 1/1996, p. 4 · TI 1/1996, p. 7 — 036 QS lubrication: solid grease arrows and hollow chain-oil arrows differ.
Part numbers (1)
- 0781 120 1111 — Mobilplex grease; solid-arrow jointsHistorical specified material; no substitute inferred · 036 QS; exact TI05/1999 locations only
Wrong number or missing part for the 036 QS? Report a correction →