← 029/039 · MS 290/310/390

Stihl 1127 · Section D · 4 of 12 · 37 parts

Oil pump, Clutch

Fits 029, 039.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192220212223242526272728293303132456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (37)

PosPart numberDescriptionQty
1 1127 640 3204 Oil pump 1
2 0000 958 0408 Washer 2
3 0000 997 0615 Compression spring 1
4 1127 647 0602 Pump piston 0.88 mm 1
5 1127 647 0601 Pump piston 0.88 mm Fitment / change note → 1
6 1121 641 9400 Bearing bushing 1
7 1128 647 4806 Control bolt 1
8 9380 620 1090 Roll pin 2x10 1
9 9646 945 0160 O-ring 4x2 2
10 1127 640 9200 Elbow connector 1
11 9645 945 7444 O-ring 4x1.5 1
12 1127 647 9400 Hose 1
13 1127 640 3800 Pickup body 1
14 9075 478 3015 Pan head self-tapping screw IS-D4x15 2
15 1125 640 7110 Worm 1
16 1125 647 2400 Spring 1
17 1127 162 3200 Carrier 1
18 1125 162 0802 Clutch shoe 3
19 1127 162 3000 Retainer 3
20 0000 997 0909 Tension spring 3
21 1127 162 1000 Cover washer 1
22 1125 162 3201 Carrier 1
23 1125 162 3000 Retainer 1
24 1125 640 2008 Chain sprocket 0.325" 8T 1
24 1125 640 2004 Chain sprocket 3/8" 7T 1
25 9512 933 2260 Needle cage 10x13x10 1
26 0000 958 1021 Washer Ø 33 mm 1
27 9460 624 0801 E-clip 8x1.3 1
28 0000 642 1231 Rim sprocket 3/8" 7T 1
29 not sold separately Clutch drum not available as a separate item 1
30 0000 958 1022 Washer Ø 27 mm 1
31 0000 642 1234 NLA Rim sprocket 0.325" 8T 1
32 0000 642 1236 NLA Rim sprocket 0.325" 7T 1
Not numbered on the diagram — assemblies, kits and options
— 1127 160 2051 Clutch 1
— 1125 007 1002 Rim sprocket kit 3/8" 7T 1
— 1125 007 1000 NLA Rim sprocket kit 0.325" 8T 1
— 1125 007 1001 NLA Rim sprocket kit 0.325" 7T 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 029 / 039

029 / 039 oil pump identification: stroke, grooves and printed delivery figures

039 gains 0.88-mm piston; 029 retains 0.75 mm. Delivery table omits a time denominator.

  • 039 new oil pump 1127 640 3201 uses 0.88-mm (0.035-in) piston 1127 647 0601. 029 CONTINUES with pump 1127 640 3200 and 0.75-mm (0.030-in) piston 1127 647 0600. Stroke is not piston diameter or oil quantity.
  • Figure 139TI 009K: piston 1 is 1127 647 0600; piston 2 is 1127 647 0601. TWO GROOVES NEXT TO THE DRIVE TEETH identify the 0.88-mm version. No groove dimensions are supplied; these figure labels are not table ordering keys.
  • Printed MAXIMUM oil feed at 10000 rpm:0.75-mm pump 15 cm³ (0.4 fl.oz); 0.88-mm pump 17.5 cm³ (0.6 fl.oz). The source prints NO TIME DENOMINATOR and does not specify which fluid-ounce convention. Do not silently append /min, infer a test duration or normalize the inconsistent-looking rounded unit pairs. These are retained source values, not a complete measured-flow acceptance test.
  • Prose introduction IN THE NEAR FUTURE; summary IN PROGRESS. No serial cutoff is given. The two complete pumps include their respective pistons, not both piston types in each pump. New pump and piston MOQ 1; old pump/piston remain spares FOR 029 (remark 1); all other parts as before.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 25/1995, p. 2 · TI 25/1995, p. 3 — Section3 specifications, figure139TI009K and summary.

Part numbers (4)
  • 1127 640 3200 — Original oil pump, 0.75-mm stroke029 retained; original 039 before upgrade · 029 / 039; Section 3 specifications, figure 139TI 009K and summary
  • 1127 640 3201 — 039 oil pump, 0.88-mm stroke039 only; MOQ 1 · 029 / 039; Section 3 specifications, figure 139TI 009K and summary
  • 1127 647 0600 — Pump piston, 0.75 mmfigure 1; retained 029 spare · 029 / 039; Section 3 specifications, figure 139TI 009K and summary
  • 1127 647 0601 — Pump piston, 0.88 mmfigure 2; two grooves; MOQ 1 · 029 / 039; Section 3 specifications, figure 139TI 009K and summary

Service note · 029 / 039

039 oil pump upgrade: higher-output pump and piston prohibited on 029

Older 039 may receive the new piston in its original pump; shared IPL is not permission for 029.

  • NEITHER the 039 oil pump 1127 640 3201 NOR new piston 1127 647 0601 MAY BE INSTALLED IN 029. Because 029 fuel consumption is lower, its oil tank would run dry BEFORE the fuel tank; continued cutting can damage bar and chain. Restriction covers BOTH complete pump and piston-only substitution.
  • OLDER 039 saws MAY be upgraded with 0.88-mm piston 1127 647 0601 in ORIGINAL pump 1127 640 3200. This direction-specific 039 upgrade does not authorize the same change on 029, generic pump interchange or successor-model conversions. The TI gives no detailed pump disassembly/adjustment procedure.
  • Later shared 029/039 D sheet lists oil pump 1127 640 3204 at key 1 and 0.88-mm pistons 1127 647 0602 at key 4 and 1127 647 0601 at key 5. Its generic shared-model rows do NOT override the explicit 1995 prohibition. No 3200/3201-to 3204 or 0600/0601-to 0602 supersession chain, later applicability exception or interchange is established here; preserve this unresolved catalog/source applicability tension.
  • Footer April 6, 1995, D1/MTK-sc; prior 029/039 TI 39/1994 is bibliographic. Notice says TI 24/1995 concerns specific sales territories and was not issued in all countries; a complete country list is unspecified. This notice does not make the retained TI 24 pages unavailable or create a missing-page gap.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 25/1995, p. 3 — Section3 service note, retained spares and footer.

Part numbers (3)
  • 1127 640 3201 — 039 higher-output oil pumpPROHIBITED on 029 · 029 / 039; Section 3 service note, retained spares and footer
  • 1127 647 0601 — 0.88-mm pump pistonPROHIBITED on 029; older 039 upgrade permitted · 029 / 039; Section 3 service note, retained spares and footer
  • 1127 640 3200 — Original oil pumpolder 039 accepts new piston; 029 retains original configuration · 029 / 039; Section 3 service note, retained spares and footer

Wrong number or missing part for the 029, 039? Report a correction →