Stihl 1127 · Section F · 6 of 12 · 24 parts
Ignition system
Fits 029, 039.
Historical fitment & changes (10) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1127 400 1200 | Flywheel Fitment / change note → | 1 |
| 2 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 3 | 0000 400 1300 | Ignition module Fitment / change note → → replaced by 1122 400 1311, 0000 400 1305, 0000 400 1305 TI 51/1994 | 1 |
| 4 | not sold separately | Ignition lead 175 mm not available as a separate item | 1 |
| 5 | 0000 989 1010 | Grommet | 1 |
| 6 | 0000 448 1250 | Lead retainer | 1 |
| 7 | 9291 021 0120 | Washer 5.3 | 1 |
| 8 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 2 |
| 9 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 9 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 10 | 1128 405 1000 | Spark plug boot | 1 |
| 11 | 0000 998 0604 | Torsion spring | 1 |
| 12 | 1127 440 3001 | Wiring harness Fitment / change note → | 1 |
| 13 | 0000 989 0814 | Grommet Fitment / change note → | 1 |
| 14 | 1125 084 8900 | Grommet Fitment / change note → | 1 |
| 15 | 1123 440 2200 | Ground wire Fitment / change note → | 1 |
| 16 | 9075 478 3015 | Pan head self-tapping screw IS-D4x15 | 1 |
| 17 | 1127 141 2200 | Manifold | 1 |
| 18 | 9771 021 2620 | Hose clip Ø 36x5 | 1 |
| 19 | 1127 141 8600 | Impulse hose | 1 |
| 20 | 0000 967 3694 | Warning pictogram Filler cap | 1 |
| 21 | 0000 967 3692 | Warning pictogram Filler cap | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 024 / 026 / 028 / 029 / 034 / 036 / 038 / 039 / 048
024–048 listed saws: aluminium-flywheel ignition module split
024, 026, 028, 029, 034, 036, 038, 039 and 048 use optimized 0000 400 1300, not the former universal 1305 recommendation.
- Applies only to the explicitly named 024, 026, 028, 029, 034, 036, 038, 039 and 048 aluminium-flywheel saws. The 044 and restricted 064 branches are separate records; a numeric span in the title does not include unnamed models.
- The reactivated 0000 400 1300 number identifies the optimized aluminium-flywheel module here. The modified version has an integrated 400 mm (15 3/4 inch) ignition lead, no separate ignition lead and no short-circuit wire. The reused number alone does not distinguish all older constructions.
- Only 0000 400 1300 is recommended for these machines. The permission to use existing 0000 400 1305 stock belongs to 046/066, not these models. No machine-number limit is supplied for these nine saws.
- TI22/1998 reports isolated reliability problems with the former universal module on aluminium-flywheel machines. Different timing requirements led to two optimized modules; this is historical manufacturer field-test guidance, not a project hardware test.
- Order only 0000 400 1300 or 1122 400 1314 according to the named model and restrictions. There is no automatic one-number replacement for 0000 400 1305.
- The 02.98 microfiche/CD-ROM issue documents the future part numbers. Both summary rows say the original 0000 400 1305 is no longer available from the factory; that does not revoke the expressly permitted use of existing stocks on eligible 046/066 machines.
- Introduction is in progress, without a new production cutoff. Factory availability is a 1998 statement, not current stock or proof of physical interchange.
Source: TI 22/1998, p. 1 · TI 22/1998, p. 2 — Sections 1–6: history, split, service note and ordering.
Part numbers (2)
- 0000 400 1305 — Former universal ignition moduleEarlier recommendation · Named saws; superseded by model-specific guidance
- 0000 400 1300 — Optimized aluminium-flywheel ignition moduleLater replacement · Only the nine explicitly named saw models
Historical fitment · 029 / 039
029 / 039: series 1127 replacement ignition assignment
0000 400 1300 and the listed flywheel pairing for series 1127; 175 mm ignition lead.
- Listed configuration: 0000 400 1300 with flywheel 1127 400 1200.
- Printed ignition-lead length: 175 mm (6 7/8 in). Preserve the printed metric and inch values; no rounding correction is inferred.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.
Part numbers (2)
- 0000 400 1300 — Replacement ignition moduleAssigned replacement · 029 / 039, series 1127, only with the listed flywheel branch
- 1127 400 1200 — Listed configuration flywheelRequired pairing · 029 / 039, series 1127; listed configuration only
Service note · 029 / 039
029 / 039: interim ground wire identification
The 15 mm tube distinguishes the interim arrangement; the instruction label alone does not.
- The bulletin addresses isolated wiring-harness/ground-wire trouble with a modified harness, a wiring/ignition-lead grommet, a second ground wire between ignition module and cylinder, and optimized routing. The tank-housing instruction label is present with both interim and new-line changes; it is not sufficient by itself to identify which arrangement is fitted.
- The interim version has a 15 mm (5/8 in as printed) tube on the additional ground wire, positioned to rest on the ignition lead (drawing 139TI001). It has NO shared wiring-harness/ignition-lead grommet. The source rates interim and new-line modifications equally good, while requiring their small differences to be observed in later repairs.
- For a faulty additional ground wire (broken or damaged insulation) in the interim arrangement, use 1123 440 2200; transfer the tube from the faulty wire to the replacement and position it on the ignition lead. This tube-transfer instruction is not permission to retain the tube when converting to the grommet-equipped harness.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 1 · TI 39/1994, p. 2 — interim ground wire identification.
Part numbers (2)
- 1123 440 2200 — Additional ground wireReplacement for faulty interim wire · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 442 2000 — 15 mm tubeInterim arrangement only · 029 / 039, subject to configuration and repair restrictions in this note
Service note · 029 / 039
029 / 039: replacement harness excludes the tube
The interim tube and new grommet MUST NOT be used together.
- On an interim-version machine with a defective wiring harness, replacement MUST be new harness 1127 440 3001. Install the completely preassembled ignition module with grommet 1125 084 8900 for the harness and ignition lead in the engine housing.
- Remove tube (1) BEFORE re-attaching the additional ground wire. Tube 1127 442 2000 and grommet 1125 084 8900 MUST NOT be used together. Do not combine the ground-wire-only interim repair with this grommet-equipped harness replacement.
- The TI does not specify a replacement ignition-module part number or a module supersession. “Preassembled” is an installation state, not proof that harness purchase includes an ignition module.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 2 — replacement harness excludes the tube.
Part numbers (3)
- 1127 440 3001 — New wiring harnessMandatory replacement for defective interim harness · 029 / 039, subject to configuration and repair restrictions in this note
- 1125 084 8900 — Shared harness/ignition-lead grommetRequired with new harness · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 442 2000 — 15 mm interim tubeRemove when fitting grommet · 029 / 039, subject to configuration and repair restrictions in this note
Service note · 029 / 039
029 / 039: new-line wiring serial boundary
X 30 222 572 is the wiring modification cutoff, not a muffler or model-production range.
X 30 222 572 — Wiring harness/grommet/additional-ground-wire line modification from this number for 029/039; not the separate muffler change or a model-identification range.
- From machine number X 30 222 572, new wiring harness 1127 440 3001 replaces 1127 440 3000. Harness and ignition lead pass together through grommet 1125 084 8900 (drawing 139TI002). Additional ground wire 1123 440 2200 connects ignition module and cylinder; strengthened cable lugs are 0.8 mm (0.03 in) thick.
- The tank-housing pictogram reminds users to tighten the fuel filler cap properly with a suitable tool after fueling. This is historical guidance for the specified machines, not a current universal filler-cap instruction.
- For repairs, replace the harness OR additional ground wire according to the fault. Grommet and instruction label are separately listed replacements. No serial end, factory-prefix meaning, model identification range or proof of the present fitted configuration is supplied.
- The page4 summary repeats the same wiring cutoff. Page5 muffler modification is instead “in progress”; this wiring cutoff must NOT be assigned to the muffler change.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 2 · TI 39/1994, p. 4 — new-line wiring serial boundary.
Part numbers (4)
- 1127 440 3000 — Original wiring harnessOriginal version · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 440 3001 — Modified wiring harnessNew-line version · 029 / 039, subject to configuration and repair restrictions in this note
- 1125 084 8900 — Shared harness/ignition-lead grommetNew-line component · 029 / 039, subject to configuration and repair restrictions in this note
- 1123 440 2200 — Additional ground wire with strengthened lugsNew-line component · 029 / 039, subject to configuration and repair restrictions in this note
Service note · 029 / 039
029 / 039: original-machine ground wire conversion
Good versus damaged wiring harnesses require different tube/grommet branches.
- The historical dealer instruction covers ALL 029 and 039 saws brought in for service or repair: check for the additional ground wire. If there is only one ground wire between ignition module and cylinder, fitting the additional wire is absolutely essential.
- If the existing harness is in GOOD condition, use kit 1127 007 1010 (1127 007 1009 for USA) to add the ground wire WITH the tube. If the harness is DAMAGED, first install the complete new harness WITH grommet 1125 084 8900, then use the appropriate kit to reach new-line status; the additional ground wire must be installed WITHOUT the tube.
- Each kit includes detailed fitting instructions and a supplement to the owner’s manual; the supplement MUST be given to the saw user. The TI allows a warranty reimbursement request in the good-harness conversion paragraph; this is historical policy, not a present warranty entitlement.
- The kit-specific fitting sheet and owner-manual supplement are not present in this five-page TI or established by the available named-file inventory. A later 1127-family service manual contains ground-wire service text but is not the exact kit insert/supplement. These named dependencies remain unverified source gaps; the TI instructions are retained, not promoted into a complete substitute kit procedure.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 2 · TI 39/1994, p. 3 · TI 39/1994, p. 4 — original-machine ground wire conversion.
Part numbers (6)
- 1127 007 1010 — Ground-wire conversion kitNon-USA kit; keys10–12 · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 007 1009 — Ground-wire conversion kit (USA)USA kit; keys10,11,13 · 029 / 039, subject to configuration and repair restrictions in this note
- 1125 084 8900 — Shared harness/ignition-lead grommetDamaged-harness conversion branch · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 440 3001 — New wiring harnessDamaged-harness replacement · 029 / 039, subject to configuration and repair restrictions in this note
- 1123 440 2200 — Additional ground wireConversion component · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 442 2000 — 15 mm tubeGood-harness interim conversion only · 029 / 039, subject to configuration and repair restrictions in this note
Service note · 029 / 039
029 / 039: ground lug placement and tightening
Connection A uses 4.0 Nm; connection B uses 4.8 Nm and the opposite additional-lug position.
- Cylinder connection A (139TI003): both cable lugs have their flat sides AGAINST ONE ANOTHER, additional ground-wire lug ON TOP. Align the lugs exactly and keep them about 2–6 mm (0.08–0.24 in) from the cylinder base. Tighten screw A to 4.0 Nm (3 lbf.ft). Do not damage or weaken lugs by bending to shape.
- Connection B (139TI004): both cable-lug flat sides face DOWNWARD; additional ground-wire lug is AT THE BOTTOM. Tighten screw B to 4.8 Nm (3.5 lbf.ft). Use a suitable BLUNT tool to push the ground wire into the arrowed slot. The source drawings locate A, B and the routing slot; the positions are not interchangeable.
- The 0.8 mm (0.03 in) thick harness and ground-wire lugs CANNOT be fitted with a standard commercial crimping tool. Replacement harnesses and ground wires are supplied only as assemblies for this reason. No substitute crimp tooling, force, wire gauge or field terminal-fabrication procedure is specified.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 3 — ground lug placement and tightening.
No additional parts-table entry added.
Service note · 029 / 039
029 / 039: harness components and supply restrictions
The unchanged small grommet is not the added shared ignition-lead grommet.
- The complete harness, including keys1–8, changes 1127 440 3000 to 1127 440 3001; original complete harness is no longer factory-available in this bulletin. Drawings139TI006/007 distinguish original and new assemblies; callout repetition indicates location, not a new part number.
- Original terminal socket4.8-1 (key1) 0751 030 8957; terminal socket4.8-1/0.4 (key5) 0751 030 8955; shrink-on tube(key6) 1123 442 0400; terminal socket3.5mm(key8) 0751 030 8490: originals remain available for OTHER MODELS, new versions are not separately supplied.
- Original cable lug A5-2.5(key2) 0751 030 8961 is deleted and no longer factory-available. Original A4-1(key3) 0751 030 8950 is deleted for this design but remains for other models. New A5-1.5 lugs(key4) are not separately supplied and have NO printed individual part number; do not invent one.
- Grommet(key7) 0000 989 0814 keeps the SAME number in both harness versions. It is distinct from added shared harness/ignition-lead grommet(key9) 1125 084 8900. New-version “-*-” cells mean no individual part number here, not a universal supersession to a neighboring numbered row.
- The complete new harness has MOQ1. Historical availability, deletion and MOQ do not establish present stock, individual installation quantities or permission to crimp replacement strengthened lugs.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 4 — harness components and supply restrictions.
Part numbers (10)
- 1127 440 3000 — Original complete harness; keys1–8No longer factory-available · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 440 3001 — New complete harness; keys1–8New assembly, MOQ1 · 029 / 039, subject to configuration and repair restrictions in this note
- 0751 030 8957 — Original terminal socket4.8-1; key1Available for other models · 029 / 039, subject to configuration and repair restrictions in this note
- 0751 030 8961 — Original cable lug A5-2.5; key2Deleted; no longer available · 029 / 039, subject to configuration and repair restrictions in this note
- 0751 030 8950 — Original cable lug A4-1; key3Deleted here; other-model availability · 029 / 039, subject to configuration and repair restrictions in this note
- 0751 030 8955 — Original terminal socket4.8-1/0.4; key5Available for other models · 029 / 039, subject to configuration and repair restrictions in this note
- 1123 442 0400 — Original shrink-on tube; key6Available for other models · 029 / 039, subject to configuration and repair restrictions in this note
- 0000 989 0814 — Small harness grommet; key7Same original/new number · 029 / 039, subject to configuration and repair restrictions in this note
- 0751 030 8490 — Original terminal socket3.5mm; key8Available for other models · 029 / 039, subject to configuration and repair restrictions in this note
- 1125 084 8900 — Added shared harness/ignition-lead grommet; key9Distinct added component · 029 / 039, subject to configuration and repair restrictions in this note
Service note · 029 / 039
029 / 039: ground-wire kit contents and regional labels
USA and non-USA kits differ in instruction label; MOQ10 tubes does not mean ten tubes installed.
- Key9 grommet1125 084 8900 MOQ1; key10 additional ground wire1123 440 2200 MOQ1; key11 tube15mm1127 442 2000 MOQ10. Key12 instruction label0000 967 3675 MOQ5; key13 USA label0000 967 3674 MOQ5.
- Conversion kit1127 007 1010 includes keys10–12 (wire,tube,non-USA label); USA kit1127 007 1009 includes keys10,11,13 (wire,tube,USA label). Each kit MOQ1. These contents do NOT include the new complete harness or shared grommet; damaged-harness conversion needs those separately.
- Tube included in a kit must still be OMITTED in the grommet-equipped branch. The diagram shows labels12/13 as alternatives, not two labels to fit together. MOQ is factory minimum order quantity, not an installed count: ten tubes or five labels are not a per-saw instruction.
- Historical TI 39/1994 guidance, not current stock or physical verification. Exact-model IPL links do not extend these instructions to MS successors. No hardware operation was performed.
Source: TI 39/1994, p. 4 — ground-wire kit contents and regional labels.
Part numbers (7)
- 1125 084 8900 — Shared grommet; key9MOQ1; outside conversion-kit contents · 029 / 039, subject to configuration and repair restrictions in this note
- 1123 440 2200 — Additional ground wire; key10Kit component; MOQ1 · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 442 2000 — 15 mm tube; key11Kit component; MOQ10 · 029 / 039, subject to configuration and repair restrictions in this note
- 0000 967 3675 — Instruction label; key12Non-USA kit label; MOQ5 · 029 / 039, subject to configuration and repair restrictions in this note
- 0000 967 3674 — Instruction label (USA); key13USA kit label; MOQ5 · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 007 1010 — Ground-wire conversion kitKeys10–12; MOQ1 · 029 / 039, subject to configuration and repair restrictions in this note
- 1127 007 1009 — Ground-wire conversion kit (USA)Keys10,11,13; MOQ1 · 029 / 039, subject to configuration and repair restrictions in this note
Historical fitment · 029 / 039
029/039 spark-plug boot collar deleted, still spare for other models
1128 084 1400 deletion is “in progress”; no serial cutoff is supplied.
- Page 2 deletes collar with loop (cover) 1128 084 1400 from the spark-plug boot on 029/039 as no longer required. The new column is a DASH, not a replacement part number; this deletes the cover, not the spark-plug boot or ignition connection.
- The introduction is “IN PROGRESS”, with NO serial number. Do not borrow X 33 373 883 from the separate fuel-cap change on page 1. Remark 1 retains the collar as a SPARE FOR OTHER MODELS, without identifying which models; no global obsolescence is inferred.
- The previous-TI pointer is 25.95 and the closing date is November 14, 1995. These are source context, not exact manufacture dates or a cutoff for cover deletion.
- Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.
Source: TI 48/1995, p. 2 — 029/039 spark-plug boot collar deleted, still spare for other models.
Part numbers (1)
- 1128 084 1400 — Collar with loop / cover on spark-plug bootdeleted · Deleted for 029/039; retained spare for unspecified other models
Wrong number or missing part for the 029, 039? Report a correction →