Stihl 1127 · Section H · 8 of 12 · 41 parts
Handle housing
Fits 029, 039.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (41)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1127 790 1001 | Handle housing | 1 |
| 2 | 1122 122 6602 | Collar screw | 2 |
| 3 | 1127 442 1600 | Contact spring | 1 |
| 4 | 1128 182 1005 | Throttle trigger | 1 |
| 5 | 9371 470 2640 | Cylindrical pin 5x24 | 1 |
| 6 | 1127 182 1500 | Throttle rod | 1 |
| 7 | 1117 182 0805 | Lockout lever | 1 |
| 8 | 1117 182 4500 | Torsion spring | 1 |
| 9 | 1127 967 1503 | Model plate | 1 |
| 10 | 1127 967 1507 | Model plate 029 S | 1 |
| 11 | 1127 967 1510 | Model plate 039 | 1 |
| 12 | 1127 967 1505 | Model plate 029 | 1 |
| 13 | 1117 141 1800 | Sleeve | 1 |
| 14 | 1128 121 8600 | Washer | 1 |
| 15 | 1127 120 0650 | Carburetor HD-19C Fitment / change note → | 1 |
| 16 | 1127 120 0604 | Carburetor HD-18C Fitment / change note → | 1 |
| 17 | 1127 120 0605 | Carburetor HD-21C Fitment / change note → | 1 |
| 18 | 1127 121 7000 | Baffle | 1 |
| 19 | 1127 120 1620 | Air filter | 1 |
| 19 | 1127 120 1621 | Air filter, fleece Fitment / change note → | 1 |
| 20 | 1127 120 1610 | Air filter | 1 |
| 20 | 1127 120 1611 NLA | Air filter, flocked Fitment / change note → → replaced by 1127 120 1621 TI 46/1997 | 1 |
| 21 | 1124 141 8300 | Slotted nut | 2 |
| 22 | 1124 121 9100 | Bushing Fitment / change note → | 1 |
| 23 | 9210 260 0700 | Hexagon nut M5 | 2 |
| 24 | 1127 124 1500 | Prefilter | 1 |
| 25 | 1128 123 7502 | Grommet Fitment / change note → | 1 |
| 26 | 1127 182 0900 | Switch shaft | 1 |
| 27 | 1123 791 0600 | Handle molding | 1 |
| 28 | 9075 478 3015 | Pan head self-tapping screw IS-D4x15 | 1 |
| 30 | 1123 141 2300 | Twist lock | 1 |
| 31 | 1127 790 1700 | Handlebar | 1 |
| 32 | 1123 790 9900 | Annular buffer | 2 |
| 33 | 1123 791 7300 | Plug | 2 |
| 34 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 7 |
| 35 | 1123 791 2805 | Annular buffer | 1 |
| 36 | 1123 791 7310 | Plug | 2 |
| 37 | 0000 967 3500 NLA | Instruction label | 1 |
| 38 | 0000 967 3685 | Instruction label | 1 |
| 39 | 0000 967 3605 | Warning pictogram Filler cap | 1 |
| 40 | 0000 967 3692 | Warning pictogram Filler cap | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 029 / 039
029 / 039: fleece filter under unchanged numbers
Fleece replaces flocked wire cloth; old stock, cleaning direction and replacement limits remain distinct.
- TI38/1996 replaces flocked wire cloth with fleece under UNCHANGED replacement-part numbers. Introduction is IN PROGRESS, without a serial cutoff. Remark 1 says the unmodified version is supplied until existing stocks are exhausted. A number alone therefore does not identify the material of an old-stock filter; this is a historical supply statement, not a current stock guarantee.
- The 029/039 row prints 1127 120 1611 with remark 1. Exact later IPL binding is handle-housing sheet H, key 20, not a successor MS290/310/390 filter sheet.
- The later 2012 IPL retains the label FLOCKED for this number. Keep that catalog wording and the 1996 fleece statement side by side; no silent catalog correction, later reversion or material identity is inferred.
- The source calls fleece especially suitable for dry and dusty conditions. Its rougher surface may look heavily contaminated when only lightly loaded; appearance alone does not establish loading. Clean DAILY OR when there is a noticeable loss of power during cutting. The observation about appearance does not cancel that interval.
- If possible, carefully blow out at LOW PRESSURE from the CLEAN AIR SIDE. For stubborn dirt or caked fleece, wash in a clean, NON-FLAMMABLE solution, for example warm soapy water. DO NOT CLEAN WITH A BRUSH: it forces dirt into the fleece. No pressure value, drying time or alternate solvent is specified.
- The source attributes improved filtering efficiency to the material structure, not a measured result here. Some trapped particles cannot be cleaned out; replace the filter when cleaning intervals become too short for practical use, or when noticeable cutting-power loss persists after thorough cleaning.
- Historical guidance for these named models and filter configurations only; no successor-model fitment, universal interchange or material identity inferred from a shared part number. No hardware operation was performed.
Source: TI 38/1996, p. 1 · TI 38/1996, p. 2 — Complete filter-material and servicing guidance; exact model summary rows and remarks.
Part numbers (1)
- 1127 120 1611 — Air filterunchanged material-revision number · 029 / 039; TI38/1996 row and configuration conditions
Conditional replacement · 029 / 039
029 / 039: compensator filter and connecting sleeve
The molded filter stub connects to the carburetor end cover through sleeve 1124 121 9100.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- Original filter 1127 120 1611 becomes 1127 120 1621, with compensator stub integrally molded on the inner half. Sleeve 1124 121 9100 joins filter and carburetor end-cover stubs; page 3 figure 1 is this sleeve.
- The TI claims longer operation between cleanings and lower maintenance costs, not maintenance-free operation or a measured project result. The table calls the filter fleece; the later IPL calls the old 1611 flocked. Source descriptions remain distinct.
- The original filter remains available for older machines. Introduction in progress; no serial cutoff. Do not infer a stand-alone filter swap is a complete compensator retrofit.
Source: TI 46/1997, p. 3 · TI 46/1997, p. 6 · TI 46/1997, p. 7 — Sections 3.1/3.5 rows 1–2 and connection drawing.
Part numbers (3)
- 1127 120 1611 — Original air filterFilter connection · 029/039; match compensator configuration
- 1127 120 1621 — Compensator air filterFilter connection · 029/039; match compensator configuration
- 1124 121 9100 — Connecting sleeveFilter connection · 029/039; match compensator configuration
Conditional replacement · 029 / 039
029 / 039 EPA: HD18A and HD21A remain model-specific
029 uses HD18A with jet 56; 039 uses HD21A with jet 58.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- Page 3 deletes HD5 1127 120 0601 in favor of 029 HD18A 1127 120 0604 and 039 HD21A 1127 120 0605. Page 7 explicitly restricts these branches to EPA machines; HD19A for non-EPA machines is separate.
- New valve jet 1128 121 5403 optimizes part-load running. Semi-fixed full-load jets: 029 uses 1120 121 5600 (Ø0.56, table fixed jet 56); 039 uses 1127 121 5602 (Ø0.58, fixed jet 58). Do not swap jets based on a shared sheet.
- Figure 3.2 items 1–6: caps limit H/L travel; knurled H and L screw heads hold caps; O-rings seal screws to carburetor body; insert bore lugs restrict cap movement; end cover has compensator stub. These figure numbers are not the page 7 parts-table numbers.
- Page 7: HD18A includes items 3–6,10,14–16,18; HD21A includes 3–6,10,14,15,17,18. Common new H screw 1128 122 6703 and L screw 1127 122 6801 each include item 10 sealing ring, which is NOT separately available. Two caps 4203 121 2700. All other parts as HD19 carburetor.
- The later IPL calls the same assembly numbers HD18C/HD21C. TI46 explicitly says A; reused numbers do not establish that every later internal setting/part is identical. No introduction serial supplied.
Source: TI 46/1997, p. 3 · TI 46/1997, p. 6 · TI 46/1997, p. 7 — Section 3.2 function and 3.5 EPA assembly/component rows.
Part numbers (9)
- 1127 120 0601 — Original HD5 carburetorEPA branch · Only model/configuration stated in conditions
- 1127 120 0604 — 029 EPA HD18A carburetorEPA branch · Only model/configuration stated in conditions
- 1127 120 0605 — 039 EPA HD21A carburetorEPA branch · Only model/configuration stated in conditions
- 1128 121 5403 — Valve jetEPA branch · Only model/configuration stated in conditions
- 1120 121 5600 — 029 jet 56EPA branch · Only model/configuration stated in conditions
- 1127 121 5602 — 039 jet 58EPA branch · Only model/configuration stated in conditions
- 1128 122 6703 — Item 14 H screw including sealing ringEPA branch · Only model/configuration stated in conditions
- 1127 122 6801 — Item 15 L screw including sealing ringEPA branch · Only model/configuration stated in conditions
- 4203 121 2700 — Item 18 limiter cap, twoEPA branch · Only model/configuration stated in conditions
Conditional replacement · 029 / 039
029 / 039 non-EPA: HD19A replacement and complete component changes
HD19A replaces HD5 only on machines without EPA approval; the original end cover is supplied for non-compensator machines.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- New replacement HD19A 1127 120 0650 is for all 029/039 WITHOUT EPA approval. HD5 1127 120 0601 is no longer available from factory. Original end cover 4116 121 0800 comes with HD19A for use on machines WITHOUT compensator; the drawing shows both end-cover forms. This is not EPA-removal advice.
- Rows 3–6: valve jet 1115 121 5401 →1128 121 5403; gasket 1127 129 0900 →1128 129 0906; end cover 4116 121 0800 →1128 121 0801; round-head screw 1106 122 7400 →1121 122 7101.
- Rows 7–9: two springs 4116 122 3001 →1128 122 3003; H screw 1127 122 6700 →1127 122 6701; L screw 4116 122 6800 →1127 122 6802. Each new screw includes item 10 sealing ring. Item 10 has no orderable number and is NOT available separately; the printed -*- is not a part number.
- Rows 11–13: retaining ring 1116 122 9000 has no new counterpart; fixed jet 58 changes 1127 121 5600 →1127 121 5602; sealing ring 1120 122 3600 has no new counterpart. All other parts as HD5. The dash does not itself authorize omitting an old part from an older assembly.
- Carburetor parts kit 1127 007 1060 →1127 007 1062 includes changed gasket item 4; all other parts as before. Remark 1 retains all marked original components and original kit as spares for older machines, distinct from HD5’s no-longer-available remark 2. Introduction in progress.
- The later IPL calls 1127 120 0650 HD19C; do not silently relabel this TI’s HD19A or copy later internals backward.
Source: TI 46/1997, p. 6 · TI 46/1997, p. 7 — Section 3.5 HD5/HD19A diagram, rows 3–13, kit and remarks 1–4.
Part numbers (22)
- 1127 120 0601 — Original HD5Original or new as described · 029/039 NON-EPA only; match component version
- 1127 120 0650 — Replacement HD19AOriginal or new as described · 029/039 NON-EPA only; match component version
- 1115 121 5401 — Original valve jetOriginal or new as described · 029/039 NON-EPA only; match component version
- 1128 121 5403 — New valve jetOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 129 0900 — Original gasketOriginal or new as described · 029/039 NON-EPA only; match component version
- 1128 129 0906 — New gasketOriginal or new as described · 029/039 NON-EPA only; match component version
- 4116 121 0800 — Original end cover; also supplied for no compensatorOriginal or new as described · 029/039 NON-EPA only; match component version
- 1128 121 0801 — New compensator end coverOriginal or new as described · 029/039 NON-EPA only; match component version
- 1106 122 7400 — Original round-head screwOriginal or new as described · 029/039 NON-EPA only; match component version
- 1121 122 7101 — New round-head screwOriginal or new as described · 029/039 NON-EPA only; match component version
- 4116 122 3001 — Original spring, twoOriginal or new as described · 029/039 NON-EPA only; match component version
- 1128 122 3003 — New spring, twoOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 122 6700 — Original H screwOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 122 6701 — New H screw including ringOriginal or new as described · 029/039 NON-EPA only; match component version
- 4116 122 6800 — Original L screwOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 122 6802 — New L screw including ringOriginal or new as described · 029/039 NON-EPA only; match component version
- 1116 122 9000 — Original retaining ringOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 121 5600 — Original jet 58Original or new as described · 029/039 NON-EPA only; match component version
- 1127 121 5602 — New jet 58Original or new as described · 029/039 NON-EPA only; match component version
- 1120 122 3600 — Original sealing ringOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 007 1060 — Original carburetor kitOriginal or new as described · 029/039 NON-EPA only; match component version
- 1127 007 1062 — New carburetor kitOriginal or new as described · 029/039 NON-EPA only; match component version
Conditional replacement · 029 / 039
029 / 039: new grommet and symbol-free replacement cover
The grommet follows the new carburetor shape; the service cover can serve both machine versions.
- Historical TI46/1997 guidance for the named 029/039 configurations only, not MS successors or every shared-sheet variant. No hardware operation was performed.
- Grommet 1128 123 7502 replaces 1128 123 7500 together with the new carburetors. It guides the carburetor screwdriver, fits the illustrated carburetor-body recess and sits flush with limiter caps.
- Production carburetor-box cover receives H3/4, L1/4 symbol. Replacement cover 1127 140 1900 will be supplied WITHOUT a setting symbol and can therefore serve original and new versions. A symbol-free cover does not identify which carburetor setting applies; identify actual carburetor/configuration.
Source: TI 46/1997, p. 5 · TI 46/1997, p. 6 — Sections 3.3–3.4 and grommet drawing.
Part numbers (3)
- 1128 123 7500 — Original guide grommetVersion-specific replacement · 029/039 as stated
- 1128 123 7502 — New shaped guide grommetVersion-specific replacement · 029/039 as stated
- 1127 140 1900 — Symbol-free replacement carburetor-box coverVersion-specific replacement · 029/039 as stated
Wrong number or missing part for the 029, 039? Report a correction →