← 029/039 · MS 290/310/390

Stihl 1127 · Section D · 4 of 13 · 31 parts

Engine housing

Fits MS 290, MS 310, MS 390.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516161717181819220212223242526272829330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 1127 020 3003 Engine housing 1
2 1128 640 9100 Valve 1
3 0000 974 1200 Notched pin 2.6x8 1
4 1120 162 5200 Pin 1
5 1127 664 2400 Collar screw Fitment / change note → 1
6 1127 790 9900 Annular buffer 1
7 9645 945 7444 O-ring 4x1.5 1
8 1121 162 5200 Pin 1
9 1123 162 5205 Pin 1
10 1123 162 5200 Pin 1
11 0000 967 3662 Warning pictogram MS 1
12 1127 664 2405 Collar screw 1
13 0000 350 0525 Filler cap 2
14 9645 948 7734 O-ring 25x3.5 2
15 1127 350 0500 Filler cap 1
16 0000 359 1220 Sealing ring 1
17 0000 350 0900 Rope 1
18 0000 353 0600 Hook 1
19 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
20 1123 791 7300 Plug 1
21 1117 350 5800 Tank vent → replaced by 0000 350 5802, 0000 350 5800 TI 5/2002 1
22 1120 358 8105 Vent insert 2
23 1127 358 7703 Hose 1
24 0000 350 3500 Pickup body 1
25 not sold separately Spur gear not available as a separate item 1
26 not sold separately Adjusting screw not available as a separate item 1
27 1127 640 1900 Tensioner slide 1
28 1123 664 1400 Thrust pad 1
29 1127 664 2200 Cover 1
30 9075 478 3015 Pan head self-tapping screw IS-D4x15 1
Not numbered on the diagram — assemblies, kits and options
— 1127 007 1003 Spur gear / chain adjusting screw kit 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 290 / MS 310 / MS 390

MS 290, MS 310, MS 390: oversized repair stud at 16 Nm

1127 664 2400 (8 mm) → 1127 664 2410 (9 mm); damaged polymer-housing threads only.

  • Exact table scope: MS 290, MS 310, MS 390. Standard stud 1127 664 2400 has diameter 8 mm; repair stud 1127 664 2410 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
  • Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
  • DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
  • Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
  • No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
  • Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.

Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 290, MS 310, MS 390: oversized repair stud at 16 Nm.

Part numbers (2)
  • 1127 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 290, MS 310, MS 390: oversized repair stud at 16 Nm
  • 1127 664 2410 — Oversized repair stud, diameter 9 mmconditional-repair · MS 290, MS 310, MS 390: oversized repair stud at 16 Nm

Wrong number or missing part for the MS 290, MS 310, MS 390? Report a correction →