Stihl 1128 · Section B · 2 of 17 · 40 parts
Cylinder
Fits 044.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 020 1227 | Cylinder with piston Ø 50 mm — 70.7 cc | 1 |
| 2 | 1128 030 2015 | Piston Ø 50 mm Fitment / change note → — 70.7 cc | 1 |
| 3 | 1128 034 3000 | Piston ring Ø 50x1.2 mm — 70.7 cc | 2 |
| 4 | 1128 034 1501 | Piston pin 12x8x35 Fitment / change note → | 1 |
| 5 | 9463 650 1200 | Snap ring 12x1 Fitment / change note → | 2 |
| 6 | 1122 025 2200 | Plug | 1 |
| 7 | 1128 020 9400 | Decompression valve | 1 |
| 8 | 1122 084 1405 | Cover | 1 |
| 9 | 1128 029 2301 | Cylinder gasket 0.5 mm Fitment / change note → | 1 |
| 10 | 9512 003 3061 | Needle cage 12x15x15 Fitment / change note → | 1 |
| 11 | 9022 371 1050 | Spline screw IS-M5x25 | 4 |
| 12 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 4 |
| 13 | 1128 141 3201 | Cooling plate Fitment / change note → | 1 |
| 14 | 1125 149 0601 | Muffler gasket | 1 |
| 15 | 1128 140 0600 | Muffler | 1 |
| 16 | 1128 145 0803 | Exhaust casing | 1 |
| 17 | 1128 140 0607 | Muffler Fitment / change note → | 1 |
| 18 | 1128 140 0604 | Muffler Fitment / change note → | 1 |
| 19 | 1118 141 9006 | Screen | 1 |
| 20 | 1128 145 0804 | Exhaust casing | 1 |
| 21 | 1128 149 0500 | Gasket Fitment / change note → | 1 |
| 22 | 9022 341 0980 | Spline screw IS-M5x16 | 2 |
| 23 | 9022 341 0910 | Spline screw IS-M5x6 | 2 |
| 24 | 9022 341 1300 | Spline screw IS-M6x20 Fitment / change note → | 2 |
| 25 | 0000 148 6000 | Tensioning gear | 2 |
| 26 | 1128 140 0610 | Muffler | 1 |
| 27 | 1128 145 0710 | Inlet casing | 1 |
| 28 | 1128 145 8000 | Sleeve | 1 |
| 29 | 9022 341 1070 | Spline screw IS-M5x30 | 1 |
| 30 | 9022 341 0910 | Spline screw IS-M5x6 | 1 |
| 31 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 32 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 33 | 1128 029 0500 | Gasket | 1 |
| 45 | 1128 140 0607 | Muffler Fitment / change note → | 1 |
| 46 | 9512 003 2340 | Needle cage 10x14x13 | 1 |
| 47 | 1128 020 1229 | Cylinder with piston Ø 50 mm — 70.7 cc | 1 |
| 48 | 1128 030 2000 | Piston Ø 50 mm Fitment / change note → — 70.7 cc | 1 |
| 49 | 1128 034 1500 | Piston pin 10x6x35 Fitment / change note → | 1 |
| 50 | 9463 650 1000 | Snap ring 10 Fitment / change note → | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 044
044: replacement crankcase needs heat shield and longer screws
The modified crankcase has higher muffler mounting bosses; installing it on an older 044 requires the matching heat shield and M6×20 screws.
- Replacing crankcase 1128 020 2112 with 1128 020 2117 on an older 044 requires heat shield 1128 141 3201 and M6×20 screws 9022 341 1300.
- Do not reuse the original M6×18 screw choice for this modified-case installation. The shield compensates for the raised bosses.
- The TI says shield and screws were included only for a transitional period; check actual replacement contents.
- This case retrofit does not authorize fitting an EPA-only muffler to an older non-EPA machine.
- The muffler mounting bosses are raised 1.0 mm, the heat-shield thickness, and extended to the rear for the longer M6 × 20 screws. The supplied transitional set contains the shield and two screws.
- The shield is installed between cylinder and muffler to protect both cylinder and crankcase from radiated heat; the source attributes its need to the higher temperature caused by the smaller exhaust opening. This does not authorize that EPA-only muffler on a non-EPA machine.
- The engine summary states introduction from the start of EPA-version production and the original 044 crankcase remains factory-supplied only while stocks last. The original M6 × 18 screw is 9022 341 1310; no new torque is printed here.
Source: TI 47/1997, p. 6 · TI 47/1997, p. 7 · TI 47/1997, p. 8 — Sections 4.1–4.5: crankcase service note and summary; full section, drawing and summary context reviewed in batch26.
Part numbers (6)
- 1128 020 2112 — CrankcaseOriginal equipment · 044 original case
- 1128 020 2117 — CrankcaseConditional replacement · 044 with matching heat shield and screws
- 1128 141 3201 — Heat shieldRequired companion · 044 modified case
- 9022 341 1310 — M6×18 screwOriginal equipment · 044 original case
- 9022 341 1300 — M6×20 screwRequired companion · 044 modified case
- 9022 341 1310 — M6 × 18 original muffler screwOriginal short screw · 044 original case geometry
Conditional replacement · 044
044: newer muffler is restricted to EPA equipment
TI 47/1997 does not make muffler 1128 140 0604 a universal replacement for 1128 140 0607.
- Modified muffler 1128 140 0604 is only documented for the EPA-approved configuration. Older non-EPA machines retain original muffler 1128 140 0607.
- The new muffler casings use gasket 1128 149 0500.
- The 044 EPA installation also uses the modified crankcase, heat shield and M6×20 screws described in the linked crankcase note.
- Introduction is the start of EPA-version production, not a numeric serial range.
- The lower-casing exhaust opening is reduced from 18 mm to 10.5 mm on the 044. Drawing132TI018 marks the opening as dimension a. This is a manufactured-version distinction, not an instruction to drill or restrict a muffler.
- Gasket 1128 149 0500 seals between the two muffler casings. The original larger-opening muffler remains a spare for machines without EPA approval; this is historical supply information.
Source: TI 47/1997, p. 7 · TI 47/1997, p. 8 — Sections 4.3–4.5: muffler restriction and summary; full section, drawing and summary context reviewed in batch26.
Part numbers (3)
- 1128 140 0607 — MufflerOriginal configuration retained · 044 older non-EPA machines
- 1128 140 0604 — MufflerRestricted new configuration · 044 EPA-equipped machines only
- 1128 149 0500 — Muffler casing gasketRequired companion · 044 modified muffler
Conditional replacement · 044
044 flush-handle version: cylinder gasket thickness changes
The flush-cut handlebar version changes from a 1.0 mm to a 0.5 mm cylinder gasket, matching the wrap-around version.
- This change is explicitly for the 044 flush-cut handlebar version: 1128 029 2302 (1.0 mm) → 1128 029 2301 (0.5 mm).
- Do not infer that every model or every original gasket should be thinned. No numeric introduction cutoff is provided.
- The source says the 1.0 mm gasket is no longer technically necessary on the flush-cut handlebar version; the replacement 0.5 mm gasket is the same as the wrap-around version. The original thicker gasket remains a spare for other versions, not a universal supersession.
- The summary introduction is from the start of EPA-version production. Its row heading is printed6.1 although the body section is7.1; the original numbering mismatch is retained rather than silently renumbered.
Source: TI 47/1997, p. 10 · TI 47/1997, p. 11 — Sections 7.1 and 7.3: flush-cut model and gasket table; full section, drawing and summary context reviewed in batch26.
Part numbers (2)
- 1128 029 2302 — 1.0 mm cylinder gasketOriginal flush-handle version · 044 flush-cut handlebar configuration
- 1128 029 2301 — 0.5 mm cylinder gasketNew flush-handle version · 044 flush-cut version; same gasket as wrap-around version
Conditional replacement · 044
044: piston/cylinder interchange works in one direction
The new piston is documented for old and new cylinders; the old piston is restricted to the old cylinder.
- New piston 1128 030 2015 may be used in the previous and new cylinder versions. Old piston 1128 030 2001 must be used only in the previous cylinder, not the new one.
- Cylinder-with-piston assembly: 1128 020 1213 → 1128 020 1226. The assembly number is not a bare-cylinder part number.
- Introduction depends on handle variant: 044 flush handle from 1 48 533 494; 044 wrap handle from 1 48 532 794. No single model-wide cutoff is inferred.
- Ring locating-pin positions changed for the wider intake port. The source says normal shop equipment cannot reliably measure the angle; identify the revision by its packaging part number.
- TI44/2000 section 1 prints the uprated 044 output as 5.4 HP (4.0 kW). This is the bulletin’s historical configuration, not a universal model rating or a measured output of a repaired saw. Cylinder and piston optimization is described for both models; the filter-base revision is explicitly 046 only.
- Summary item 1 is the cylinder-with-piston assembly including item 2, the separately listed piston. Do not treat the assembly number as a bare cylinder or add a second piston to its stated contents.
- Remark 1 applies to both summary rows: the previous versions are no longer available from the factory at the time of this TI. This is not current stock information, a prohibition on the permitted old-cylinder combination, or permission to reverse the one-way piston interchange.
- Drawing 145TI050 KN illustrates the two locating-pin angles marked a without giving numerical angles. The TI supplies no port-width dimensions, machining procedure or reliable visual measurement shortcut; packaging identification remains required.
- Power chronology remains unresolved: this TI already prints 4.0 kW for uprated 044 variants, while TI06/2001 contrasts 3.8 kW 044 with 4.0 kW MS440. Preserve market/version uncertainty; neither a universal power-change date nor MS440 part applicability follows from these ratings.
Source: TI 44/2000, p. 1 · TI 44/2000, p. 2 — Complete sections 1–2: uprated engine, piston/cylinder service direction, 046 filter base, all summary rows and handle-specific cutoffs.
Part numbers (4)
- 1128 020 1213 — Cylinder with pistonPrevious assembly · 044 previous cylinder version
- 1128 020 1226 — Cylinder with pistonNew assembly · 044 new cylinder; old piston prohibited
- 1128 030 2001 — PistonRestricted old version · 044 previous cylinder only
- 1128 030 2015 — PistonNew version · 044 previous or new cylinder
Conditional replacement · 044
044: enlarged crank gear is not individually interchangeable
From X 29 382 283, larger big-end and small-end bearings require matched crankshaft, crankcase, piston, pin, rings and cage. The new crankshaft must not be fitted in either named older crankcase.
X 29 382 283 — Introduction of enlarged matched crank gear; not an unconditional replacement boundary.
- Do not install crankshaft 1128 030 0405 in original crankcases 1128 020 2106 or 1128 020 2103. The source says original and new crank-gear component parts are not interchangeable; it does not authorize an arbitrary mixed-parts conversion.
- The new big-end bearing is wider and larger in diameter; increased crankpin radius r requires more crank-chamber clearance for the connecting rod. Small-end bore a identifies the crankshaft: old 14 mm (0.55 in), new 15 mm (0.59 in). These bore sizes are not piston-pin diameters.
- Standard cylinder/piston 1128 020 1201 changes to 1128 020 1211; automatic-choke cylinder/piston 1128 020 1204 changes to 1128 020 1212. Original assemblies include table items 1,3,5 (old piston, pin and two C10 rings); new assemblies include 2,4,6 (new piston, pin and two C12 rings). Both cylinders are 50 mm bore; that alone does not establish interchange.
- Piston pin changes from 10x6x35 to 12x8x35; the corresponding needle cage changes from 10x14x13 to 12x15x15. Table keys are component references, not assembly ordering numbers.
- Original crankcase 1128 020 2106 is while-stocks-last; the original crankshaft, cylinder/piston assemblies, piston, pin, snap rings and needle cage remain for older machines in this bulletin.
- The original cage is printed 9512 535 2340 in both the original scan and text. The catalog uses 9512 003 2340 for a 10x14x13 cage. No alias or corrected order number is inferred from matching dimensions.
- TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.
Source: TI 16/1994, p. 1 · TI 16/1994, p. 2 — Sections1.1–1.5, crank gear diagrams and full summary.
Part numbers (17)
- 1128 020 2106 — Original crankcaseProhibited with new crankshaft · 044 configuration described in this record
- 1128 020 2103 — Earlier crankcaseProhibited with new crankshaft · 044 configuration described in this record
- 1128 020 2112 — Enlarged crankcaseNew configuration · 044 configuration described in this record
- 1128 030 0401 — Original crankshaft14 mm small-end bore · 044 configuration described in this record
- 1128 030 0405 — Enlarged crankshaft15 mm small-end bore · 044 configuration described in this record
- 1128 020 1201 — Standard cylinder with pistonOld matched set · 044 configuration described in this record
- 1128 020 1211 — Standard cylinder with pistonNew matched set · 044 configuration described in this record
- 1128 020 1204 — Automatic-choke cylinder with pistonOld matched set · 044 configuration described in this record
- 1128 020 1212 — Automatic-choke cylinder with pistonNew matched set · 044 configuration described in this record
- 1128 030 2000 — Piston 50 mmOld · 044 configuration described in this record
- 1128 030 2001 — Piston 50 mmNew · 044 configuration described in this record
- 1128 034 1500 — Piston pin 10x6x35Old · 044 configuration described in this record
- 1128 034 1501 — Piston pin 12x8x35New · 044 configuration described in this record
- 9463 650 1000 — Snap ring C10, two requiredOld · 044 configuration described in this record
- 9463 650 1200 — Snap ring C12, two requiredNew · 044 configuration described in this record
- 9512 535 2340 — Needle cage 10x14x13, as printedOld; ordering identity not reconciled with catalog · 044 configuration described in this record
- 9512 003 3061 — Needle cage 12x15x15New · 044 configuration described in this record
Historical fitment · 044
044: cylinder gasket standardized to the automatic-choke design
Cylinder gasket 1128 029 2300 is replaced by 1128 029 2301, the design already introduced with automatic choke.
- The paired drawing labels the original gasket on the left and the new design on the right. The part relationship is explicit, not inferred from the pictures alone.
- Introduction is in progress, without a numeric changeover. The original gasket is no longer factory supplied in this bulletin. No gasket thickness or new torque is specified here.
- The cover index lists cylinder gasket as item8, while the body labels it section7 after starter-post section6.2. This numbering difference does not indicate a missing page: seven original scans match seven text pages.
- The final TI54/1992 reference is bibliographic and does not import its unavailable contents.
- TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.
Source: TI 16/1994, p. 7 — Section7, gasket drawing and full summary.
Part numbers (2)
- 1128 029 2300 — Original cylinder gasketHistorical version · 044 configuration described in this record
- 1128 029 2301 — Standardized cylinder gasketHistorical version · 044 configuration described in this record
Wrong number or missing part for the 044? Report a correction →