← 044/046 · MS 440/460/461

Stihl 1128 · Section A · 1 of 17 · 44 parts

Crankcase, Crankshaft

Fits 044.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1110111213141516171819220212223242526272828293303132333544546474849550505152536789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (44)

PosPart numberDescriptionQty
1 1128 020 2122 Crankcase Fitment / change note → → replaced by 1128 020 2136 TI 15/2007 1
2 0000 988 5211 Connector 1
3 9371 470 2610 Cylindrical pin 5x18 2
4 0000 974 1200 Notched pin 2.6x8 1
5 1128 640 9100 Valve 1
6 9503 003 0346 Grooved ball bearing 6202 Fitment / change note → 1
7 9523 003 4275 Grooved ball bearing 15x35x13 1
8 0000 953 6605 Collar screw M8 2
9 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 5
10 1120 162 5200 Pin 1
11 1121 162 5205 Pin 1
12 1128 162 5200 Pin 1
13 1121 162 5200 Pin 1
14 1128 084 8302 Reflector foil 1
15 1128 647 9405 Hose 1
16 1117 640 3800 Pickup body 1
17 9640 003 1320 Oil seal 13x19x4 1
18 9640 003 1972 Oil seal 18x29.6x5/3 1
19 9640 951 1972 Oil seal 18x29.6x5/3 1
20 1128 029 0500 Gasket 1
21 1128 030 0406 Crankshaft 1
22 1120 036 8500 Woodruff key 2x3.7 1
23 1124 791 2800 Stop buffer 1
24 1125 007 1021 Spur gear / chain adjusting screw kit 1
25 9646 945 0490 O-ring 7x1.5 1
26 1125 640 1900 Tensioner slide 1
27 1122 664 2200 Cover plate 1
28 9041 216 0630 Pan head screw M4x8 Fitment / change note → 2
29 1125 664 1400 Thrust pad 1
30 1122 664 4500 Support 1
31 1128 664 1001 Inner side plate 0.9 mm Fitment / change note → → replaced by 1128 664 1002 TI 12/1994 1
32 1128 664 1002 NLA Inner side plate Fitment / change note → → replaced by 1128 664 1001, 1128 664 1001 TI 10/2007 option 1
33 1133 791 5900 Stop buffer 1
35 9645 948 7734 O-ring 25x3.5 1
45 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
46 0000 359 1220 Sealing ring 1
47 0000 350 0900 Rope 1
48 0000 353 0600 Hook 1
49 1128 030 0401 Crankshaft Fitment / change note → → replaced by 1128 030 0405 TI 16/1994 1
50 1128 020 2103 Crankcase Fitment / change note → 1
51 0000 992 6302 Sealing ring 1
52 1117 350 0905 Filler cap retainer 1
53 9099 021 2360 Self-tapping screw 3.5x9.5 1
Not numbered on the diagram — assemblies, kits and options
— 1128 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 044

044: replacement crankcase needs heat shield and longer screws

The modified crankcase has higher muffler mounting bosses; installing it on an older 044 requires the matching heat shield and M6×20 screws.

  • Replacing crankcase 1128 020 2112 with 1128 020 2117 on an older 044 requires heat shield 1128 141 3201 and M6×20 screws 9022 341 1300.
  • Do not reuse the original M6×18 screw choice for this modified-case installation. The shield compensates for the raised bosses.
  • The TI says shield and screws were included only for a transitional period; check actual replacement contents.
  • This case retrofit does not authorize fitting an EPA-only muffler to an older non-EPA machine.
  • The muffler mounting bosses are raised 1.0 mm, the heat-shield thickness, and extended to the rear for the longer M6 × 20 screws. The supplied transitional set contains the shield and two screws.
  • The shield is installed between cylinder and muffler to protect both cylinder and crankcase from radiated heat; the source attributes its need to the higher temperature caused by the smaller exhaust opening. This does not authorize that EPA-only muffler on a non-EPA machine.
  • The engine summary states introduction from the start of EPA-version production and the original 044 crankcase remains factory-supplied only while stocks last. The original M6 × 18 screw is 9022 341 1310; no new torque is printed here.

Source: TI 47/1997, p. 6 · TI 47/1997, p. 7 · TI 47/1997, p. 8 — Sections 4.1–4.5: crankcase service note and summary; full section, drawing and summary context reviewed in batch26.

Part numbers (6)
  • 1128 020 2112 — CrankcaseOriginal equipment · 044 original case
  • 1128 020 2117 — CrankcaseConditional replacement · 044 with matching heat shield and screws
  • 1128 141 3201 — Heat shieldRequired companion · 044 modified case
  • 9022 341 1310 — M6×18 screwOriginal equipment · 044 original case
  • 9022 341 1300 — M6×20 screwRequired companion · 044 modified case
  • 9022 341 1310 — M6 × 18 original muffler screwOriginal short screw · 044 original case geometry

Conditional replacement · 044

044 repair: newer crankcase requires its matching oil cap

TI 06/2001 permits the new crankcase to be used for 044 repairs with the cap that matches its modified oil-filler opening.

  • Crankcase 1128 020 2119 → 1128 020 2122 changes the oil-filler opening. Use cap 0000 350 0525 with that new opening; do not infer a cap-only retrofit to the old case.
  • The new cap was to be supplied with the replacement crankcase for about three years. Verify actual parts supplied today.
  • This is the specific case-and-cap repair described for 044; it is not blanket 044/MS 440 interchangeability.
  • Introduction is in progress without a numeric serial cutoff; retained edition is english / USA. Historical factory-availability remarks are not current stock information.
  • The tool-free cap has a grip for operation and is the same type for fuel and oil. To open, raise the grip upright, turn about one-quarter turn counterclockwise, and remove. To close, fit with grip upright and the cap/opening marks aligned, turn about one-quarter turn clockwise to the stop, then fold the grip down. The closing check is that the grip’s lug engages the recess; merely folding the grip down is not the stated check. Drawings 176TI001–004 KN show this sequence for the matching opening.
  • Summary item 6 includes items 7 and 8: matching oil filler cap 0000 350 0525 and ball bearing 6202, now 9503 003 0346. The previous oil-cap cell is a dash, not a supplied old-cap number. Remark 1 marks the previous crankcase no longer available from the factory.

Source: TI 6/2001, p. 1 · TI 6/2001, p. 2 · TI 6/2001, p. 3 · TI 6/2001, p. 4 — Complete sections 1–9: 044/MS440 naming and power chronology, split-filter intake, cap operation, matching assemblies, vent construction/function, main bearing, clutch and all 17 summary rows.

Part numbers (5)
  • 1128 020 2119 — CrankcaseOriginal equipment · 044 previous case
  • 1128 020 2122 — CrankcaseConditional repair replacement · 044 repair with modified oil opening and matching cap
  • 0000 350 0525 — Oil filler capRequired companion · Modified crankcase opening only
  • 9503 003 0340 — 6202 main bearingPrevious included bearing · Corresponding crankcase configuration in TI06/2001
  • 9503 003 0346 — 6202 main bearingNew included bearing · Corresponding crankcase configuration in TI06/2001

Historical fitment · 044 / 046

044 / 046: ignition-side bearing becomes open on both sides

TI 47/1997 changes the ignition-side bearing; it expressly leaves clutch-side bearing numbers unchanged.

  • Ignition side only: 9503 003 6555 → 9503 003 0340, open on both sides instead of the shield-washer version.
  • This is not a clutch-side replacement rule. Later 1999 and 2001 bearing revisions remain separately dated records.
  • Both crankcase summary rows include the new 6202 bearing. The 046 crankcase number remains 1128 020 2116 despite the bearing change; unchanged part number is not proof of unchanged contents. The clutch-side bearing numbers remain unchanged.
  • The summary says original bearing and 044 crankcase remain factory-supplied while stocks last; unmodified 046 crankcases likewise continue until stocks are exhausted. The summary introduction says start of EPA-version production, while the cover excludes section4.2 from the emission-compliance modifications; no numeric bearing cutoff is inferred.

Source: TI 47/1997, p. 1 · TI 47/1997, p. 7 · TI 47/1997, p. 8 — Sections 4.2 and 4.5: bearing and summary; full section, drawing and summary context reviewed in batch26.

Part numbers (3)
  • 9503 003 6555 — Ignition-side bearingOriginal version · 044 / 046 ignition side
  • 9503 003 0340 — Ignition-side bearingNew open version · 044 / 046 ignition side, 1997 revision
  • 1128 020 2116 — 046 crankcase including ignition-side bearingUnchanged assembly number · 046; bearing contents revised

Historical fitment · 044 / MS 440

044 → MS 440: 6202 bearing replacement

TI 06/2001 specifies a main-bearing number change to standardize parts inventories.

  • The documented 6202 bearing change is 9503 003 0340 → 9503 003 0346.
  • Do not apply the 046 serial cutoff from TI 03/1999 to this 044/MS 440 transition; TI 06/2001 says introduction was in progress. This is not an all-bearing replacement rule.
  • Introduction is in progress without a numeric serial cutoff; retained edition is english / USA. Historical factory-availability remarks are not current stock information.
  • Section 6 states parts-inventory standardization as the reason. Summary item 8 is included in crankcase item 6; remark 1 marks the old bearing no longer available from the factory. No bearing material, clearance, seal specification or new installation procedure is given; designation 6202 alone does not identify every compatible commercial bearing.

Source: TI 6/2001, p. 1 · TI 6/2001, p. 2 · TI 6/2001, p. 3 · TI 6/2001, p. 4 — Complete sections 1–9: 044/MS440 naming and power chronology, split-filter intake, cap operation, matching assemblies, vent construction/function, main bearing, clutch and all 17 summary rows.

Part numbers (2)
  • 9503 003 0340 — 6202 main bearingPrevious version · 044 predecessor configuration
  • 9503 003 0346 — 6202 main bearingReplacement version · 044 / MS 440 transition

Conditional replacement · 044

044: modified housings add AV stop buffers

The modified crankcase and tank housing provide openings for additional AV stops.

1 41 628 724 — 044 AV stop/housing introduction; not the 046 cylinder-screw cutoff.

  • Crankcase 1128 020 2117 → 1128 020 2119 adds the opening for stop buffer 1125 791 2810 below the ignition module. Install the buffer from the side facing the tank housing.
  • Tank housing 1128 350 0815 → 1128 350 0813 adds the opening for plug 1110 145 9001, used as a stop buffer.
  • The supplied openings are part of this change; no drilling or universal buffer-only retrofit is established.
  • The summary lists crankcase item 1 including stop buffer item 2, and tank housing item 3 including plug item 4. These are historical supply descriptions, not guarantees of current package contents.
  • Remark 1 says the original 044 crankcase 1128 020 2117 and tank housing 1128 350 0815 were no longer available from the factory at the bulletin date.
  • The AV introduction also says annular buffers were modified, but gives no separate annular-buffer part number or dimensional change. Do not infer a buffer-only retrofit.

Source: TI 3/1999, p. 1 · TI 3/1999, p. 3 — Sections 1 and 3: AV openings and 044 summary.

Part numbers (6)
  • 1128 020 2117 — CrankcaseOriginal version · 044
  • 1128 020 2119 — CrankcaseModified AV version · 044 with stop-buffer opening
  • 1125 791 2810 — Stop bufferNew companion · 044 modified crankcase
  • 1128 350 0815 — Tank housingOriginal version · 044
  • 1128 350 0813 — Tank housingModified AV version · 044 with plug opening
  • 1110 145 9001 — Plug / stop bufferNew companion · 044 modified tank housing

Conditional replacement · 044 / 064 / 066

044 / 064 / 066: sprung side plate requires the revised cover

Side plate 1128 664 1001 changes to 1128 664 1002; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.

  • When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
  • The separate 1122-group cover row applies ONLY to 044 and 066 with wrap-around handles. It does not extend that cover to 064 or every 044/066.
  • Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
  • The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
  • The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
  • For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
  • Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
  • Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
  • Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.

Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.

Part numbers (7)
  • 1128 664 1001 — Original side platePrevious version · Retained for original cover
  • 1128 664 1002 — Sprung-tab side plateNew version · Requires new-version cover
  • 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
  • 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
  • 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
  • 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
  • 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping

Conditional replacement · 044

044: enlarged crank gear is not individually interchangeable

From X 29 382 283, larger big-end and small-end bearings require matched crankshaft, crankcase, piston, pin, rings and cage. The new crankshaft must not be fitted in either named older crankcase.

X 29 382 283 — Introduction of enlarged matched crank gear; not an unconditional replacement boundary.

  • Do not install crankshaft 1128 030 0405 in original crankcases 1128 020 2106 or 1128 020 2103. The source says original and new crank-gear component parts are not interchangeable; it does not authorize an arbitrary mixed-parts conversion.
  • The new big-end bearing is wider and larger in diameter; increased crankpin radius r requires more crank-chamber clearance for the connecting rod. Small-end bore a identifies the crankshaft: old 14 mm (0.55 in), new 15 mm (0.59 in). These bore sizes are not piston-pin diameters.
  • Standard cylinder/piston 1128 020 1201 changes to 1128 020 1211; automatic-choke cylinder/piston 1128 020 1204 changes to 1128 020 1212. Original assemblies include table items 1,3,5 (old piston, pin and two C10 rings); new assemblies include 2,4,6 (new piston, pin and two C12 rings). Both cylinders are 50 mm bore; that alone does not establish interchange.
  • Piston pin changes from 10x6x35 to 12x8x35; the corresponding needle cage changes from 10x14x13 to 12x15x15. Table keys are component references, not assembly ordering numbers.
  • Original crankcase 1128 020 2106 is while-stocks-last; the original crankshaft, cylinder/piston assemblies, piston, pin, snap rings and needle cage remain for older machines in this bulletin.
  • The original cage is printed 9512 535 2340 in both the original scan and text. The catalog uses 9512 003 2340 for a 10x14x13 cage. No alias or corrected order number is inferred from matching dimensions.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 1 · TI 16/1994, p. 2 — Sections1.1–1.5, crank gear diagrams and full summary.

Part numbers (17)
  • 1128 020 2106 — Original crankcaseProhibited with new crankshaft · 044 configuration described in this record
  • 1128 020 2103 — Earlier crankcaseProhibited with new crankshaft · 044 configuration described in this record
  • 1128 020 2112 — Enlarged crankcaseNew configuration · 044 configuration described in this record
  • 1128 030 0401 — Original crankshaft14 mm small-end bore · 044 configuration described in this record
  • 1128 030 0405 — Enlarged crankshaft15 mm small-end bore · 044 configuration described in this record
  • 1128 020 1201 — Standard cylinder with pistonOld matched set · 044 configuration described in this record
  • 1128 020 1211 — Standard cylinder with pistonNew matched set · 044 configuration described in this record
  • 1128 020 1204 — Automatic-choke cylinder with pistonOld matched set · 044 configuration described in this record
  • 1128 020 1212 — Automatic-choke cylinder with pistonNew matched set · 044 configuration described in this record
  • 1128 030 2000 — Piston 50 mmOld · 044 configuration described in this record
  • 1128 030 2001 — Piston 50 mmNew · 044 configuration described in this record
  • 1128 034 1500 — Piston pin 10x6x35Old · 044 configuration described in this record
  • 1128 034 1501 — Piston pin 12x8x35New · 044 configuration described in this record
  • 9463 650 1000 — Snap ring C10, two requiredOld · 044 configuration described in this record
  • 9463 650 1200 — Snap ring C12, two requiredNew · 044 configuration described in this record
  • 9512 535 2340 — Needle cage 10x14x13, as printedOld; ordering identity not reconciled with catalog · 044 configuration described in this record
  • 9512 003 3061 — Needle cage 12x15x15New · 044 configuration described in this record

Historical fitment · 044

044 fuel system: pickup and cap retainer have different changeovers

The larger pickup begins at X 29 382 309; the filler-cap cord attaches directly to tank eyes from the earlier X 28 030 485. Neither threshold applies to the other change.

  • Pickup 1115 350 3503 → 0000 350 3500 from X 29 382 309. The new body has a larger filter area; improved service life and dirt retention are vendor claims, not measured here.
  • Old pickup body is no longer factory supplied. Original filter 1110 358 1800 remains for older machines; the new filter is not a separate spare. Original weight 1115 358 8200 and cap 1115 358 2500 are while-stocks-last. The old body includes these three illustrated items; they are not asserted to fit inside the new body.
  • Separately, from X 28 030 485 the filler-cap cord clips directly into an eye in the tank housing; suitable eyes are provided in fuel and oil tanks. The production hook is deleted. The filler-cap part number remains unchanged but is not printed here; no catalog cap number is inferred.
  • Replacement filler caps continue to be supplied with a hook. The service note requires removing that hook before installing the filler cap in a crankcase with eyes. This is conditional on the observed housing configuration, not universal removal of every cap hook.
  • The two printed X-prefix serials are distinct historical production thresholds; neither supplies a global number range or retrofit approval for later models.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 5 · TI 16/1994, p. 6 — Sections4–5, both summaries, drawings and filler-cap service note.

Part numbers (5)
  • 1115 350 3503 — Original pickup bodyHistorical version · 044 configuration described in this record
  • 0000 350 3500 — Revised larger-filter pickup bodyHistorical version · 044 configuration described in this record
  • 1110 358 1800 — Original pickup filterHistorical version · 044 configuration described in this record
  • 1115 358 8200 — Original pickup weightHistorical version · 044 configuration described in this record
  • 1115 358 2500 — Original pickup capHistorical version · 044 configuration described in this record

Service note · 044 / 046

044 / 046: bumper-to-crankcase screw retention

During repairs, TI05/1996 specifies Loctite 242 for the spiked-bumper/crankcase mounting screws.

  • Section 2 applies within the bulletin’s 044/046 scope and calls for securing the spiked-bumper/crankcase mounting screws with Loctite 242 in the course of repairs. It is not a production changeover or a direction for every bumper fastener.
  • No screw ordering number, thread, tightening torque, adhesive quantity or cure time is printed in this section. Do not fabricate a part match or generalize this statement to the chain-sprocket-cover bumper, guide-bar nuts or other screws.
  • This is a source-bound historical service note, not evidence of completed hardware work, current adhesive equivalence or successor-model applicability.

Source: TI 5/1996, p. 2 — Section 2: Spiked bumper; explicit repair application.

No additional parts-table entry added.

Wrong number or missing part for the 044? Report a correction →