Stihl 1128 · Section D · 4 of 17 · 36 parts
Chain brake, Chain sprocket cover
Fits 044.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 790 9150 | Hand guard Fitment / change note → | 1 |
| 2 | 1124 084 8300 | Reflector foil | 1 |
| 3 | 1124 792 5500 | Bushing Fitment / change note → | 1 |
| 4 | 1124 792 5505 | Bushing Fitment / change note → | 1 |
| 5 | 9022 341 1080 | Spline screw IS-M5x35 Fitment / change note → | 1 |
| 6 | 1128 790 9151 | Hand guard | 1 |
| 7 | 1128 084 8303 | Reflector foil | 1 |
| 8 | 1128 792 0900 | Reflector foil | 1 |
| 9 | 1128 160 5000 | Lever | 1 |
| 10 | 9460 624 0400 | E-clip 4 | 2 |
| 11 | 1121 162 5010 | Lever | 1 |
| 12 | 0000 997 0628 | Spring | 1 |
| 13 | 1128 160 5400 | Brake band | 1 |
| 14 | 1128 160 5501 | Tension spring | 1 |
| 15 | 1128 162 8000 | Hose | 1 |
| 16 | 1128 021 1101 | Cover Fitment / change note → | 1 |
| 17 | 1128 021 1105 | Cover | 1 |
| 18 | 9022 313 0660 | Spline screw IS-M4x12 | 4 |
| 19 | 1125 640 1701 | Chain sprocket cover Fitment / change note → → replaced by 1122 640 1702, 1128 640 1706 TI 36/2000 | 1 |
| 20 | 1125 656 1501 | Guard | 1 |
| 21 | 1122 648 0401 | Chain sprocket cover Fitment / change note → → replaced by 1122 648 0403 TI 15/2007 | 1 |
| 22 | 1121 648 6610 | Bumper strip | 2 |
| 23 | 1122 656 1510 | Guard | 1 |
| 24 | 1122 664 0501 | Bumper spike | 1 |
| 25 | 9008 319 0960 | Hexagon head screw M5x12 | 2 |
| 26 | 9214 320 0700 | Lock nut M5 | 3 |
| 27 | 1122 650 7700 | Chain catcher | 1 |
| 28 | 1122 664 0506 | Bumper spike | 1 |
| 29 | 1128 664 0500 | Bumper spike | 1 |
| 30 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 31 | 1122 656 7700 | Chain catcher | 1 |
| 32 | 9022 341 1019 | Spline screw IS-M5x20 | 1 |
| 33 | 0000 955 0801 | Hexagon nut M8 | 2 |
| 34 | 0000 967 3714 | Instruction label ARCTIC | 1 |
| 35 | 0000 967 3612 | Instruction label | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 007 1019 | Chain sprocket cover kit | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 044
Brake spring and cover must be matched
The larger brake spring was introduced with a modified cover. The bulletin lists 1128 160 5550 as the spring-with-cover assembly.
X 31 850 438 — Modified brake spring introduced from this machine number.
- Do not install the new spring with original cover 1128 021 1100. Use modified cover 1128 021 1101.
- The modified cover is documented for all 044 versions. The bulletin’s supply arrangement up to 1996 does not establish current kit contents.
- The spring diameter is enlarged; the source gives no numeric diameter. Summary assembly 1128 160 5550 includes item 1 spring and item 2 cover; the new separate-spring cell is marked not available separately until 1996. The prose says spring supplied with cover up to 1996. Neither wording establishes an exact day in 1996 when separate supply began.
- Original cover 1128 021 1100 is no longer available from the factory in this TI; all other brake parts are as before. The all 044-versions claim concerns the new cover, not blanket interchange of the larger spring with old covers or successor models.
- The brake changeover X 31 850 438 is distinct from both filter-element X 31 098 388 and HD-cover X 31 849 638. None is a universal whole-saw early/late boundary.
Source: TI 20/1995, p. 3 — Section 2: Chain brake, service note and summary.
Part numbers (4)
- 1128 160 5500 — Brake springOriginal equipment · 044 original brake
- 1128 160 5550 — Brake spring with coverNew assembly · 044; modified cover required
- 1128 021 1100 — Brake coverOriginal equipment · Not compatible with the new spring
- 1128 021 1101 — Brake coverRequired companion · New spring; also documented for all 044 versions
Conditional replacement · 044
044: hand-guard replacement needs both bushings and screw
Interchangeability applies to the complete new hand guard, with its brass bushing, rubber bushing and M5×35 screw.
- For 044, replace 1128 790 9100 with complete hand guard 1128 790 9150; the 044 and 046 guards have different numbers.
- Fit both bushings (1124 792 5500 and 1124 792 5505) and screw 9022 341 1080. The brass-bushing flange points inward.
- Do not infer bare-guard interchange using the old mounting hardware. Introduction was in progress; no numeric serial is supplied.
- The new guard is supported in a rubber bushing on the fan side. Before installation, push brass bushing (2) into rubber bushing (3), then fit both into guard (1), brass flange inward, and secure with M5 × 35 screw (4). The source calls original and complete new assemblies fully interchangeable within the stated model; it does not permit bare-guard substitution.
- The table includes bushings and screw with each new guard. Original guards remain factory-supplied only while stocks last. Old screw-and-washer assembly 0000 790 6103 remains available as a spare for other models, not as the new guard fastener; those other models are not identified.
Source: TI 47/1997, p. 9 · TI 47/1997, p. 10 — Section 6: front hand guard and summary; full section, drawing and summary context reviewed in batch26.
Part numbers (6)
- 1128 790 9100 — Hand guardOriginal equipment · 044
- 1128 790 9150 — Hand guardConditional replacement · 044 complete with both bushings and screw
- 1124 792 5500 — Brass bushingRequired companion · 044 new guard, flange inward
- 1124 792 5505 — Rubber bushingRequired companion · 044 new guard
- 9022 341 1080 — IS M5×35 screwRequired companion · 044 new guard
- 0000 790 6103 — Original screw and washer assemblyHistorical original mounting hardware · Retained for unnamed other models; not new guard installation
Conditional replacement · 044 / 064 / 066
044 / 064 / 066: sprung side plate requires the revised cover
Side plate 1128 664 1001 changes to 1128 664 1002; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.
- When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
- The separate 1122-group cover row applies ONLY to 044 and 066 with wrap-around handles. It does not extend that cover to 064 or every 044/066.
- Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
- The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
- The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
- For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
- Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
- Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
- Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.
Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.
Part numbers (7)
- 1128 664 1001 — Original side platePrevious version · Retained for original cover
- 1128 664 1002 — Sprung-tab side plateNew version · Requires new-version cover
- 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
- 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
- 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
- 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
- 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
Conditional replacement · 044 / 066
044 / 066 wrap-around handle: distinct revised sprocket cover
Only the 044 and 066 wrap-around-handle configurations are named for cover 1122 640 1700 → 1122 640 1701, paired with the revised side plate.
- Wrap-around handle only; not 064, ordinary-handle configurations or successor saws. The 044 catalog link is a related cover sheet, not proof that its standard-cover row depicts this wrap-around cover.
- When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
- The separate 1122-group cover row applies ONLY to 044 and 066 with wrap-around handles. It does not extend that cover to 064 or every 044/066.
- Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
- The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
- The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
- For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
- Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
- Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
- Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.
Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.
Part numbers (7)
- 1128 664 1001 — Original side platePrevious version · Retained for original cover
- 1128 664 1002 — Sprung-tab side plateNew version · Requires new-version cover
- 1122 640 1700 — Wrap-around-handle chain sprocket coverPrevious general cover · 044/066 wrap-around handles only
- 1122 640 1701 — Wrap-around-handle chain sprocket coverNew general cover · 044/066 wrap-around handles only
- 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
- 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
- 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
Wrong number or missing part for the 044? Report a correction →