← 044/046 · MS 440/460/461

Stihl 1128 · Section J · 9 of 17 · 46 parts

Automatic choke parts

Fits 044.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262728293303132333435442434445464748495506789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (46)

PosPart numberDescriptionQty
1 1128 020 1212 Cylinder with piston Ø 50 mm — 70.7 cc 1
2 1128 030 2001 Piston Ø 50 mm — 70.7 cc 1
3 1128 034 3000 Piston ring Ø 50x1.2 mm — 70.7 cc 2
4 1128 034 1501 Piston pin 12x8x35 1
5 9463 650 1200 Snap ring 12x1 2
6 1128 029 2301 Cylinder gasket 0.5 mm 1
7 1128 120 5010 Control valve 1
8 9646 951 0340 O-ring 6x1.5 1
9 1128 120 9200 Elbow connector 1
10 9646 951 0150 O-ring 4x1 1
11 1128 121 2300 Support 1
12 1128 122 9300 Clip 1
13 not sold separately Hose 3.1x5.7x87 mm, R3 not available as a separate item 1
14 1128 120 4800 Bellows 1
15 1128 122 2500 Hose clip 1
16 1128 120 1500 Filter 1
17 not sold separately Foamfilter not available as a separate item 1
18 1128 120 0615 Carburetor C3M-S12B Fitment / change note → 1
19 1128 182 1501 Throttle rod 1
20 1128 180 3501 Switch housing 1
21 1128 442 1600 Contact spring 1
22 1128 442 1601 Contact spring 1
23 1128 180 0902 Switch shaft 1
24 0000 997 0227 Compression spring 1
25 1128 182 1700 Slide control 1
26 1128 120 1625 Air filter 1
27 1128 140 1905 Carburetor box cover 1
28 1124 140 9500 Twist lock 1
29 1128 141 4001 Slide 1
30 1128 080 1610 Shroud 1
31 1121 084 7100 Cap 1
32 1128 084 8301 Reflector foil 1
33 0000 963 0808 Bushing 3
34 1128 967 1508 Model plate 044 C 1
35 1124 121 9100 Bushing 1
42 1128 020 1204 Cylinder with piston Ø 50 mm — 70.7 cc 1
43 1128 030 2000 Piston Ø 50 mm — 70.7 cc 1
44 1128 034 1500 Piston pin 10x6x35 1
45 9463 650 1000 Snap ring 10 2
46 1128 084 4100 Shutter 1
47 1128 084 6200 Washer 1
48 9460 624 0400 E-clip 4 1
49 1128 967 1501 Model plate 044 C 1
50 0000 974 1000 Round head rivet 3x6 2
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1
— 0712 923 8004 Hose 3.1x5.7 mm x 10 m, R3 not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 044

044 automatic choke: serial table has a production exception

C3M-S12B replaces earlier automatic-choke carburetors, but S21 production continues temporarily. Replacing S12A requires a compensator-compatible filter or a separately ordered non-compensator end cover.

  • Column A up to X 26 452 475 lists C3M-S12A 1128 120 0603. Column B from X 26 452 476 to X 28 047 977 lists C3M-S21 1128 120 0609. Column C from X 28 047 978 lists C3M-S12B 1128 120 0615 with an explicit note.
  • The note says automatic-choke saws will still be built for a while with C3M-S21; C3M-S12B is already being shipped as a replacement unit. Therefore X 28 047 978 is not a guaranteed automatic-choke production cutoff. No end serial for the exception is supplied.
  • When replacing S12A 1128 120 0603 with S12B 1128 120 0615, either install an air filter with compensator connection OR replace the supplied compensator end cover with 1125 121 0803 without a compensator connection. The latter must be ordered separately.
  • The A/C idle-system relationship and B-to-C component roster apply to the named configuration, not an automatic conversion of every carburetor. The source summary marks old S21 as no longer supplied from the factory, while the narrative preserves temporary production use; these are different supply contexts.
  • TI54/1992, referenced for earlier A-to-B changes, is absent from the retained corpus. This is not replaced by an inferred generic conversion procedure.
  • TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.

Source: TI 16/1994, p. 3 · TI 16/1994, p. 4 — Automatic-choke table row, column-C note and service note.

Part numbers (4)
  • 1128 120 0603 — Automatic-choke C3M-S12AHistorical version · 044 configuration described in this record
  • 1128 120 0609 — Automatic-choke C3M-S21Historical version · 044 configuration described in this record
  • 1128 120 0615 — Automatic-choke C3M-S12BHistorical version · 044 configuration described in this record
  • 1125 121 0803 — End cover without compensator connectionHistorical version · 044 configuration described in this record

Wrong number or missing part for the 044? Report a correction →