Stihl 1128 · Section H · 8 of 17 · 46 parts
Tank housing
Fits 044.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (46)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 350 0844 | Tank housing | 1 |
| 2 | 1128 122 6606 | Collar screw Fitment / change note → | 2 |
| 3 | 1128 358 7703 | Hose | 1 |
| 4 | 0000 350 5800 | Tank vent Fitment / change note → → replaced by 0000 350 5804 TI 41/2003 | 1 |
| 5 | not sold separately | O-ring not available as a separate item | 1 |
| 6 | 0000 967 3662 | Warning pictogram MS | 1 |
| 7 | 0000 967 3605 | Warning pictogram Filler cap | 1 |
| 8 | 1128 180 0910 | Switch shaft Fitment / change note → | 1 |
| 9 | 0000 997 0227 | Compression spring | 1 |
| 10 | 1128 182 1700 | Slide control | 1 |
| 11 | 1128 180 3501 | Switch housing | 1 |
| 12 | 1128 442 1600 | Contact spring | 1 |
| 13 | 1128 442 1601 | Contact spring | 1 |
| 14 | 9099 021 1760 | Self-tapping screw 2.9x9.5 | 1 |
| 15 | 0000 350 3504 | Pickup body | 1 |
| 16 | 1128 141 8600 | Impulse hose | 1 |
| 17 | 0000 350 0525 | Filler cap Fitment / change note → | 1 |
| 18 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 19 | 1128 182 1005 | Throttle trigger | 1 |
| 20 | 1128 182 1500 | Throttle rod | 1 |
| 21 | 1117 182 4500 | Torsion spring | 1 |
| 22 | 9371 470 2640 | Cylindrical pin 5x24 | 1 |
| 23 | 1117 182 0805 | Lockout lever | 1 |
| 24 | 1128 791 0600 | Handle molding | 1 |
| 25 | 9074 478 3076 | Pan head self-tapping screw IS-P4x19 | 1 |
| 26 | 0000 967 3405 | Instruction label no longer available from factory | 1 |
| 27 | 0000 967 3500 NLA | Instruction label | 1 |
| 31 | 1122 358 1800 | Filter Fitment / change note → | 1 |
| 32 | 1128 350 5802 | Tank vent Fitment / change note → → replaced by 0000 350 5800, 0000 350 5800 TI 5/2001 | 1 |
| 33 | 0000 350 0520 | Filler cap Fitment / change note → → replaced by 1127 350 0500 TI 48/1995 | 1 |
| 34 | 0000 359 1220 | Sealing ring | 1 |
| 35 | 0000 350 0900 | Rope | 1 |
| 36 | 0000 353 0600 | Hook | 1 |
| 37 | 1121 358 1800 | Filter Fitment / change note → → replaced by 1122 358 1800 TI 31/2000 | 1 |
| 38 | 1121 358 2500 | Cap Fitment / change note → | 1 |
| 39 | 1122 350 5851 NLA | Tank vent Fitment / change note → | 1 |
| 40 | 1125 122 6600 | Collar screw Fitment / change note → | 2 |
| 41 | 1128 350 5805 | Tank vent Fitment / change note → | 1 |
| 42 | 1120 358 8105 | Vent insert Fitment / change note → | 2 |
| 43 | 1110 358 1800 | Filter Fitment / change note → | 1 |
| 44 | 1128 180 3500 | Switch housing | 1 |
| 45 | 0000 992 6302 | Sealing ring | 1 |
| 46 | 1117 350 0905 | Filler cap retainer | 1 |
| 47 | 9099 021 2360 | Self-tapping screw 3.5x9.5 | 1 |
| 48 | 1121 442 0400 | Hose no longer available from factory | 1 |
| 49 | 0000 967 3692 | Warning pictogram Filler cap | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
IPL correction · 044 / 046
Switch shaft: 044 and 046 differ
The original switch shaft can be used in the 044, but the 046 requires the newer wedge-lever shaft.
- 1128 180 0900 is permitted in the 044, not in the 046.
- 1128 180 0910 is documented for both 044 and 046. The 046 used it from launch; the 044 change was in progress, with no serial cutoff supplied.
- The drawing labels original lever section A and new wedge-shaped choke-operating lever section B. These are shape identifiers, not part-order suffixes or installation dimensions.
- Original shaft 1128 180 0900 is deleted and no longer available from the factory in the summary. Existing stock may be used up in 044 only; the new 046 shaft was fitted from market launch despite the erroneous parts-list information. Historical deletion does not prohibit the explicitly allowed 044 use-up.
Source: TI 5/1996, p. 1 — Section 1: Switch shaft and service notes.
Part numbers (2)
- 1128 180 0900 — Switch shaftOriginal / restricted · 044 only; explicitly excluded for 046
- 1128 180 0910 — Switch shaftCorrected / new version · 044 and 046
Historical fitment · 044
044 tank housing and vent changed together
Tank housing 1128 350 0804 changed to 1128 350 0815 with a different vent system and added wiring lugs.
- The new vent system combines valve 1110 353 1600, filter 1121 358 1800 and cap 1121 358 2500; do not present the valve alone as a drop-in replacement for old vent 1128 350 5805.
- Old vent and insert remained spares for older machines according to this 1997 TI. No numeric production cutoff is given.
- The new vent also requires clearance at the carburetor box cover; see the separate TI 09/1997 cover-change note.
- The TI notes that this one-way vent can retain tank pressure when fuel warms; it instructs opening the filler cap slowly.
- The sintered filter (2) helps prevent dirt entering valve (1); cap (3) protects the filter against icing. Air enters as fuel volume decreases, but cannot flow from inside outwards through the new valve. Heating by sunlight or other influences can therefore build pressure while stopped; opening the cap slowly releases pressure gradually and limits unexpected fuel escape.
- Two integrally molded lugs hold the wires in the carburetor box, as shown in drawing 132 TI 013. The summary groups housing with items 2–6 and original vent with insert item 3; deleted original-column entries are not instructions to fit old and new vent components together.
- The change is in progress. Original housing 1128 350 0804 is no longer factory-supplied, while original vent 1128 350 5805 and insert 1120 358 8105 remain spares for older machines. These are dated supply remarks, not current availability or 046 housing fitment.
Source: TI 9/1997, p. 1 · TI 9/1997, p. 2 — Complete sections1,1.1–1.3; both vent diagrams,wiring-lug drawing,all summary rows and supply remarks.
Part numbers (7)
- 1128 350 0804 — Tank housingOriginal equipment · 044 original vent system
- 1128 350 0815 — Tank housingNew assembly · 044 revised vent system with wiring lugs
- 1128 350 5805 — Tank ventOriginal equipment · 044 older housing
- 1120 358 8105 — Vent insertOriginal equipment · 044 original tank vent
- 1110 353 1600 — Vent valveNew-system component · 044 revised vent system
- 1121 358 1800 — Vent filterRequired companion · 044 revised vent system
- 1121 358 2500 — Vent capRequired companion · 044 revised vent system
Conditional replacement · 044
044: tank-vent retrofit depends on dome shape
TI 11/2000 separates the new tank housing/vent from retrofit kit 1122 350 5851 for the previous housing.
- New 044 tank housing 1128 350 0823 replaces 1128 350 0813; it uses filter 1122 358 1800 and vent 1128 350 5802.
- For the previous housing, use retrofit kit 1122 350 5851 after removing cap 1121 358 2500 and filter 1121 358 1800; the kit is not the same part as the new-housing vent.
- Slotted dome: hose with internal spring and high thrust ring. Unslotted dome: hose without internal spring and low thrust ring. Inspect the actual housing; do not choose by model name alone.
- The summary assigns serial 1 46 173 746 only to the 046. The 044 change was in progress; no numeric 044 introduction is established.
- The new-housing vent 1128 350 5802 consists of cap (2), hose (3) and vent insert (4) in drawing 145TI037 KN; these are not separately available. Filter 1122 358 1800 is a separate summary row, not one of those three inseparable vent pieces.
- Retrofit kit 1122 350 5851 instead has connector (3), secured to the housing with thrust ring (4), and hose (5) containing a vent insert, as shown in 145TI026 KN. Its component parts are not available separately in this TI. Do not confuse these drawing numbers with the different new-housing vent drawing.
- After removing the old cap and filter and selecting the dome-specific hose/ring, place the tank vent in position. Hold it with suitable pliers and press it into the dome by carefully tapping the pliers once or twice with a mallet (145TI030/031 KN). Then fit the proper thrust ring (145TI032 KN).
- Position suitable pliers on top of the thrust ring and press the ring onto the dome by carefully tapping the pliers once or twice (145TI033 KN). Finally position the hose correctly as illustrated in 145TI034 KN. The original page 3 drawing supplies its routing; no numerical insertion depth, impact force or pressure-test specification is given.
- Summary items 1 and 2 describe the respective tank housings as including items 3–5. Item 3 has previous cap 1121 358 2500 and a dash in New; item 4 changes the filter; item 5 introduces vent 1128 350 5802 with no Previous number. Preserve that historical column context: the old cap is not an additional component to fit with the new complete vent. Item 6 introduces the separate retrofit kit, not a replacement for item 5.
- Summary remark 1: previous tank housings are no longer factory-supplied. Remark 2: the previous cap and filter remain available for older machines. Remark 3: kit 1122 350 5851 is for upgrading the previous housing. These are historical supply statements, not present stock or unrestricted interchange.
- Page 1 states the housing change from 1 46 173 746 and older housing through 1 46 173 745 without a model qualifier; page 3 explicitly assigns the introduction to 046 and says 044 is in progress. Preserve both statements and the narrower model-specific summary; no numeric 044 production boundary is established.
- These instructions cover the 044/046 dome-dependent retrofit in this TI. They do not recover the separate kit instruction sheet referenced by TI52/1999 or establish a high/low ring part-number assignment; the latter TI’s named source gap remains separate.
Source: TI 11/2000, p. 1 · TI 11/2000, p. 2 · TI 11/2000, p. 3 — Sections 1–1.3: tank vent, dome assignment and model-specific summary; complete installation/identification drawings and supply remarks reviewed.
Part numbers (7)
- 1128 350 0813 — Tank housingOriginal equipment · 044 previous housing
- 1128 350 0823 — Tank housingNew version · 044 modified vent mounting
- 1121 358 2500 — Vent capOriginal equipment removed for retrofit · 044 previous housing
- 1121 358 1800 — Vent filterOriginal equipment removed for retrofit · 044 previous housing
- 1122 358 1800 — Vent filterNew-housing component · 044 modified housing
- 1128 350 5802 — Tank ventNew-housing component · 044 modified housing, not retrofit kit
- 1122 350 5851 — Tank vent retrofit kitConditional retrofit · 044 previous housing; dome-dependent hose and thrust ring
Conditional replacement · 044
044 repair: newer tank housing requires its matching cap
TI 06/2001 expressly permits the new MS 440 tank housing to be used for 044 repairs with the matching cap and vent.
- Tank housing 1128 350 0823 → 1128 350 0832 changes the filler opening. Use cap 0000 350 0525 with the new opening; this is not evidence that the cap alone fits the old housing.
- The new housing configuration uses vent 0000 350 5800 in place of 1128 350 5802. This record does not establish a stand-alone vent retrofit to every older housing.
- The TI says the new cap would be supplied with the housing for about three years to allow 044 repairs. That historical supply arrangement does not guarantee present package contents.
- The MS 440 model transition does not establish universal interchangeability of all 044/MS 440 parts.
- Introduction is in progress without a numeric serial cutoff; retained edition is english / USA. Historical factory-availability remarks are not current stock information.
- The tool-free cap has a grip for operation and is the same type for fuel and oil. To open, raise the grip upright, turn about one-quarter turn counterclockwise, and remove. To close, fit with grip upright and the cap/opening marks aligned, turn about one-quarter turn clockwise to the stop, then fold the grip down. The closing check is that the grip’s lug engages the recess; merely folding the grip down is not the stated check. Drawings 176TI001–004 KN show this sequence for the matching opening.
- Section 1 renames 044 as STIHL MS 440 within the new naming structure (TI25/2000); the new nameplate stays on the shroud. Naming history does not establish a serial-identification range.
- Summary item 1 includes items 2–5: filler cap and vent with valve/filter contents. Remark 1 marks the previous housing no longer available from the factory; remark 2 preserves the old cap and vent for older machines. New vent internals are not additional separately orderable parts.
Source: TI 6/2001, p. 1 · TI 6/2001, p. 2 · TI 6/2001, p. 3 · TI 6/2001, p. 4 — Complete sections 1–9: 044/MS440 naming and power chronology, split-filter intake, cap operation, matching assemblies, vent construction/function, main bearing, clutch and all 17 summary rows.
Part numbers (6)
- 1128 350 0823 — Tank housingOriginal equipment · 044 previous housing
- 1128 350 0832 — Tank housingConditional repair replacement · 044 repair with new opening, cap and vent
- 0000 350 0520 — Filler capOriginal equipment · Previous tank opening
- 0000 350 0525 — Filler capRequired companion · Modified tank opening only
- 1128 350 5802 — Tank ventPrevious configuration · Previous tank housing
- 0000 350 5800 — Tank ventNew-housing configuration · Modified tank housing
Conditional replacement · 044
044: modified housings add AV stop buffers
The modified crankcase and tank housing provide openings for additional AV stops.
1 41 628 724 — 044 AV stop/housing introduction; not the 046 cylinder-screw cutoff.
- Crankcase 1128 020 2117 → 1128 020 2119 adds the opening for stop buffer 1125 791 2810 below the ignition module. Install the buffer from the side facing the tank housing.
- Tank housing 1128 350 0815 → 1128 350 0813 adds the opening for plug 1110 145 9001, used as a stop buffer.
- The supplied openings are part of this change; no drilling or universal buffer-only retrofit is established.
- The summary lists crankcase item 1 including stop buffer item 2, and tank housing item 3 including plug item 4. These are historical supply descriptions, not guarantees of current package contents.
- Remark 1 says the original 044 crankcase 1128 020 2117 and tank housing 1128 350 0815 were no longer available from the factory at the bulletin date.
- The AV introduction also says annular buffers were modified, but gives no separate annular-buffer part number or dimensional change. Do not infer a buffer-only retrofit.
Source: TI 3/1999, p. 1 · TI 3/1999, p. 3 — Sections 1 and 3: AV openings and 044 summary.
Part numbers (6)
- 1128 020 2117 — CrankcaseOriginal version · 044
- 1128 020 2119 — CrankcaseModified AV version · 044 with stop-buffer opening
- 1125 791 2810 — Stop bufferNew companion · 044 modified crankcase
- 1128 350 0815 — Tank housingOriginal version · 044
- 1128 350 0813 — Tank housingModified AV version · 044 with plug opening
- 1110 145 9001 — Plug / stop bufferNew companion · 044 modified tank housing
Conditional replacement · 044
044: longer collar screws require deeper slotted nuts
Both tank-housing and slotted-nut numbers stay unchanged despite a dimensional change.
- Collar screws 1125 122 6600 → 1128 122 6606 are 2 mm longer; tank housing 1128 350 0813 retains its number.
- Slotted nut 1124 141 8300 retains its number while thread depth changes from 8.5 mm to 10.5 mm. The number alone does not establish the depth.
- Short-thread nuts may be used only with the shorter collar screws projecting 48 mm. If projection is 50 mm, use only the new nut with 10.5 mm thread depth.
- The bulletin describes the longer screws as simplifying assembly of some models; it does not identify additional model fitment. Its diagram measures projection a from the tank housing, not total screw length.
- The nut diagram prints 8.5 mm (0.3 inch) and 10.5 mm (0.4 inch). These are the printed rounded inch labels, not substitute precision dimensions.
- The summary lists tank housing item 4 including collar screw item 5. Introduction is in progress, with no serial threshold supplied.
- At the bulletin date, unmodified tank housings were to be supplied until factory stocks were exhausted; previous collar screws remained available for other, unnamed models; previous shallow slotted nuts were no longer available from the factory. These distinct supply rules do not remove the physical depth checks.
Source: TI 35/1999, p. 1 · TI 35/1999, p. 2 — Sections 1–1.4: dimensional service note and summary.
Part numbers (4)
- 1125 122 6600 — Collar screwShorter original version · 044; 48 mm projection
- 1128 122 6606 — Collar screwLonger version · 044; 50 mm projection requires deeper nut
- 1124 141 8300 — Slotted nutSame number, different thread depth · 044; check 8.5 versus 10.5 mm depth
- 1128 350 0813 — Tank housingSame number, changed collar screws · 044; inspect actual screw projection
Historical fitment · 044
044 fuel system: pickup and cap retainer have different changeovers
The larger pickup begins at X 29 382 309; the filler-cap cord attaches directly to tank eyes from the earlier X 28 030 485. Neither threshold applies to the other change.
- Pickup 1115 350 3503 → 0000 350 3500 from X 29 382 309. The new body has a larger filter area; improved service life and dirt retention are vendor claims, not measured here.
- Old pickup body is no longer factory supplied. Original filter 1110 358 1800 remains for older machines; the new filter is not a separate spare. Original weight 1115 358 8200 and cap 1115 358 2500 are while-stocks-last. The old body includes these three illustrated items; they are not asserted to fit inside the new body.
- Separately, from X 28 030 485 the filler-cap cord clips directly into an eye in the tank housing; suitable eyes are provided in fuel and oil tanks. The production hook is deleted. The filler-cap part number remains unchanged but is not printed here; no catalog cap number is inferred.
- Replacement filler caps continue to be supplied with a hook. The service note requires removing that hook before installing the filler cap in a crankcase with eyes. This is conditional on the observed housing configuration, not universal removal of every cap hook.
- The two printed X-prefix serials are distinct historical production thresholds; neither supplies a global number range or retrofit approval for later models.
- TI16/1994 is dated March 21, 1994. Historical availability and production statements are not present inventory or verified physical interchange; no successor-model applicability is inferred.
Source: TI 16/1994, p. 5 · TI 16/1994, p. 6 — Sections4–5, both summaries, drawings and filler-cap service note.
Part numbers (5)
- 1115 350 3503 — Original pickup bodyHistorical version · 044 configuration described in this record
- 0000 350 3500 — Revised larger-filter pickup bodyHistorical version · 044 configuration described in this record
- 1110 358 1800 — Original pickup filterHistorical version · 044 configuration described in this record
- 1115 358 8200 — Original pickup weightHistorical version · 044 configuration described in this record
- 1115 358 2500 — Original pickup capHistorical version · 044 configuration described in this record
Conditional replacement · 044 / 046
044 / 046: extra thrust ring in the revised tank-vent package
The added 1128 353 0200 ring is required only on 044 and 046, not on 064/066.
Later reviewed guidance: 044: tank-vent retrofit depends on dome shape · 046: tank-vent retrofit depends on dome shape
- Section 2 replaces complete tank vent 1122 350 5850 with 1122 350 5851 in connection with 044/046 changes. The summary says introduction is in progress, with no numeric serial. The previous complete vent is no longer available from the factory (remark 1); this is a 1999 supply statement.
- The new complete vent includes items 2–4: tank vent 1122 350 5802 and thrust ring 1122 353 0200 retain their numbers, while thrust ring 1128 353 0200 is added. Remark 2 requires the added 1128 ring only for 044 and 046; inclusion in the package is not a requirement to install it on 064/066.
- A detailed instruction sheet is supplied with the vent. It is not reproduced here and was not identified in the bounded 43-file retained docs inventory. Its full installation procedure remains a named source gap; do not infer it from this parts table. TI36/1997 is retained and pending separate review, not missing or automatically reviewed by this citation.
- This 1999 TI gives no high/low ring dimensions, slotted/unslotted dome assignment or hose-spring procedure. Later TI11/2000 provides separate dome-dependent retrofit guidance for 044/046; follow those source-linked conditions without pretending this missing kit instruction sheet has been recovered.
- Historical TI52/1999 instructions and spare-availability statements are not present stock or physical interchange verification. Base-model catalog sheets are navigation anchors; printed R/M variant restrictions remain controlling. No applicability to MS 640, MS 650 or MS 660 is inferred.
Source: TI 52/1999, p. 2 — Section 2, package contents and explicit 044/046-only ring remark.
Part numbers (5)
- 1122 350 5850 — Complete tank vent, previousReplaced; no longer factory-supplied in this TI · 044 / 046 retrofit package only; not universal current-housing fitment
- 1122 350 5851 — Complete tank vent, newIncludes items 2–4; installation is model-specific · 044 / 046 retrofit package only; not universal current-housing fitment
- 1122 350 5802 — Tank vent componentUnchanged item 2 · 044 / 046 retrofit package only; not universal current-housing fitment
- 1122 353 0200 — Thrust ringUnchanged item 3 · 044 / 046 retrofit package only; not universal current-housing fitment
- 1128 353 0200 — Additional thrust ringNew item 4; required only for 044/046 · 044 / 046 retrofit package only; not universal current-housing fitment
Wrong number or missing part for the 044? Report a correction →