← 044/046 · MS 440/460/461

Stihl 1128 · Section C · 3 of 16 · 26 parts

Muffler

Fits 046.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922020212223344041414256789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (26)

PosPart numberDescriptionQty
1 1128 140 0603 Muffler 1
2 1128 145 0803 Exhaust casing 1
3 1128 140 0609 Muffler Fitment / change note → 1
4 1128 145 0804 Exhaust casing 1
5 1118 141 9006 Screen 1
6 1128 149 0500 Gasket Fitment / change note → 1
7 1128 140 0610 Muffler 1
8 1128 145 0710 Inlet casing 1
9 1128 145 8000 Sleeve 1
10 1128 140 0616 Muffler Fitment / change note → 1
11 1128 140 0801 Exhaust casing 1
12 1128 141 9000 Screen 1
13 1128 148 4200 Bracket 1
14 9099 021 0810 Self-tapping screw 4.2x9.5 2
15 1128 140 0612 Muffler 1
16 1128 145 0805 Exhaust casing 1
17 1125 149 0601 Muffler gasket 1
18 9022 341 0910 Spline screw IS-M5x6 2
19 9022 341 0980 Spline screw IS-M5x16 2
20 9022 341 1370 Spline screw IS-M6x30 Fitment / change note → 2
21 0000 148 6000 Tensioning gear 2
22 9022 341 1070 Spline screw IS-M5x30 1
23 9022 341 0910 Spline screw IS-M5x6 1
40 1128 140 0616 Muffler Fitment / change note → 1
41 9022 341 1310 Spline screw IS-M6x18 Fitment / change note → 2
42 1128 140 0608 Muffler no longer available from factory 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046: newer muffler is restricted to EPA equipment

TI 47/1997 does not make muffler 1128 140 0609 a universal replacement for 1128 140 0616.

  • Modified muffler 1128 140 0609 is only documented for the EPA-approved configuration. Older non-EPA machines retain original muffler 1128 140 0616.
  • The new muffler casings use gasket 1128 149 0500.
  • Introduction is the start of EPA-version production, not a numeric serial range.
  • The lower-casing exhaust opening is reduced from 18 mm to 9.5 mm on the 046. Drawing132TI018 marks the opening as dimension a. This is a manufactured-version distinction, not an instruction to drill or restrict a muffler.
  • Gasket 1128 149 0500 seals between the two muffler casings. The original larger-opening muffler remains a spare for machines without EPA approval; this is historical supply information.

Source: TI 47/1997, p. 7 · TI 47/1997, p. 8 — Sections 4.3–4.5: muffler restriction and summary; full section, drawing and summary context reviewed in batch26.

Part numbers (3)
  • 1128 140 0616 — MufflerOriginal configuration retained · 046 older non-EPA machines
  • 1128 140 0609 — MufflerRestricted new configuration · 046 EPA-equipped machines only
  • 1128 149 0500 — Muffler casing gasketRequired companion · 046 modified muffler

Service note · 046

046: engine fasteners and catalytic-muffler torque branches

Cylinder, crankcase, flywheel, clutch and muffler values retain thread and variant distinctions.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Cylinder/crankcase IS-M6×25: 15 Nm (11 lbf.ft); crankcase IS-M5×20: 11.5 Nm (8.5 lbf.ft); shroud/crankcase IS-M5×16: 7 Nm (5.2 lbf.ft).
  • Standard muffler top IS-M5×6: 6.5 Nm (4.8 lbf.ft), Loctite 242; muffler/cylinder IS-M5×16: 11.5 Nm (8.5 lbf.ft), Loctite 242.
  • Kat/catalytic muffler top IS-M5×30: 6.5 Nm (4.8 lbf.ft), Loctite 242; Kat muffler/cylinder IS-M6×18: 15 Nm (11 lbf.ft), Loctite 242. Separate muffler/crankcase IS-M6×18 row: 15 Nm (11 lbf.ft), with no adhesive remark printed.
  • Flywheel M8×1 nut: 32.5 Nm (24 lbf.ft); clutch M12×1 L carrier: 50 Nm (37 lbf.ft), with left-hand thread explicitly marked L.
  • Cylinder decompression valve M10×1: 14 Nm (10.3 lbf.ft), not the leakage-test plug; spark plug M14×1.25: 25 Nm (18.5 lbf.ft).

Source: TI 46/1995, p. 11 — 5.3: engine, exhaust and rotating assembly rows.

No additional parts-table entry added.

Service note · 046

046 C: catalyst construction and specifications

The catalyst version adds 300 g; power remains 4.1 kW.

  • The 046 C has the same catalytic converter as the 044 C according to this bulletin: metal carrier, rapid response of 20–30 seconds, low gas-flow resistance and platinum coating described as temperature-resistant to 1300°C (2375°F). This is not a claim that the complete mufflers interchange, a measured temperature, or a safe-touch limit.
  • The source claims approximately 70% reduction of unburnt hydrocarbons, reducing unpleasant smell and irritation of eyes and mucous membranes. These are dated manufacturer claims, not project measurements or a guarantee of safe exhaust exposure.
  • Except for 300 g (10.6 oz) extra weight, specifications are stated to match other series 046 machines: engine power unchanged at 4.1 kW (5.6 bhp), powerhead weight without bar and chain 6.8 kg (15 lbs). No fuel-fill convention is specified.
  • TI11/1993 describes the 026 C catalyst and its operation; the bulletin applies that description to 046 C except for 026-specific speeds, engine power and other model-specific data. TI11/1993 is absent from the retained inventory and scan filenames, so its detailed description remains a source gap. No 026 settings or MS460 applicability are inferred.

Source: TI 5/1997, p. 1 · TI 5/1997, p. 2 — Cover, entire section1 introduction and1.1, including TI11/1993 applicability exception.

No additional parts-table entry added.

Historical fitment · 046

046: counterbored crankcase and longer muffler screws

Replacement crankcase 1128 020 2116 requires the supplied pair of M6 × 30 screws.

  • The 046 C catalyst muffler runs hotter than the non-catalyst muffler. Its crankcase tapped holes are deeper and counterbored; drawing145TI015 contrasts original M6 × 18 and new M6 × 30 attachments, identifying muffler (1) and crankcase (2). The unchanged muffler-to-crankcase torque is 15 Nm (11.0 lbf.ft), not a general crankcase-fastener torque.
  • For parts standardization, original crankcase 1128 020 2114 without counterbores is replaced by 1128 020 2116 with counterbores. The new crankcase includes two M6 × 30 screws to ensure the stated interchangeability. That statement is conditional on the matched screw construction; it does not approve longer screws in the old shallow holes.
  • For a non-catalyst 046 repaired with new crankcase 1128 020 2116, using the supplied M6 × 30 screws to mount the muffler is essential. Secure them with Loctite 272; the source says it remains secure up to 200°C (390°F) and explicitly forbids another threadlocking adhesive for this application. This is not a limit for the catalyst coating.
  • The summary identifies old IS-M6 × 18 screw 9022 341 1310 and new IS-M6 × 30 screw 9022 341 1370 (two). Modification introduction is in progress, with no serial cutoff. The old crankcase is no longer factory-supplied, while the original short screw remains a spare for older machines; these are historical supply statements, not present inventory.
  • An instruction sheet explaining the longer screws was to be included through the end of 1998; it is not reproduced or claimed reviewed. Section3 lists Loctite 272 in a 50 ml bottle, 0786 111 1110, as required for 046 C, alongside the explicit non-catalyst repair instruction in section2.1. No different adhesive is silently substituted.

Source: TI 5/1997, p. 2 · TI 5/1997, p. 3 — Complete sections1.4,2,2.1,2.2 and section3; drawing145TI015 and all summary remarks.

Part numbers (5)
  • 1128 020 2114 — Original crankcase without counterboresSuperseded crankcase · 046 original screw geometry
  • 1128 020 2116 — Counterbored crankcase including two long screwsReplacement assembly · 046; matched M 6 × 30 screws required
  • 9022 341 1310 — IS-M6 × 18 screwOriginal short screw · older 046 crankcase; retained spare
  • 9022 341 1370 — IS-M6 × 30 screw (two)Required replacement screws · 046 new counterbored crankcase
  • 0786 111 1110 — Loctite 272, 50 ml bottleSpecified servicing aid · 046 C and stated non-catalyst replacement-crankcase repair

Wrong number or missing part for the 046? Report a correction →