Stihl 1128 · Section D · 4 of 16 · 32 parts
Oil pump, Clutch
Fits 046.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 640 3206 | Oil pump 0.8 → replaced by 1128 640 3250 TI 51/2003 | 1 |
| 2 | 0000 958 0518 | Washer | 2 |
| 3 | 0000 997 0615 | Compression spring | 1 |
| 4 | 1128 647 0606 | Pump piston 0.8 | 1 |
| 5 | 1128 647 4806 | Control bolt | 1 |
| 6 | 9380 620 1090 | Roll pin 2x10 | 1 |
| 7 | 9646 945 0160 | O-ring 4x2 | 2 |
| 8 | 1125 641 9400 | Bearing bushing | 1 |
| 9 | 1122 649 5000 | Sealing ring B4x2 | 1 |
| 10 | 9022 313 0660 | Spline screw IS-M4x12 | 2 |
| 11 | 1128 640 7112 | Worm | 1 |
| 12 | 1128 647 2400 | Spring | 1 |
| 13 | 1128 162 1001 | Cover washer 58 mm / 2 5/16'' | 1 |
| 14 | 1128 162 1000 | Cover washer 43 mm / 1 3/4'' → replaced by 1128 162 1001, 1128 162 1001 TI 37/2001 | 1 |
| 15 | 1128 162 3202 | Carrier | 1 |
| 16 | 1128 162 0807 | Clutch shoe | 3 |
| 17 | 1128 162 3000 | Retainer | 3 |
| 18 | 0000 997 5815 | Tension spring | 3 |
| 19 | 9512 933 2380 | Needle cage 10x16x12 → replaced by 9512 933 2382, 1122 967 1503 TI 53/2002 | 1 |
| 20 | 0000 642 1223 | Rim sprocket 3/8" 7T | 1 |
| 21 | not sold separately | Clutch drum not available as a separate item | 1 |
| 22 | 0000 958 1032 | Washer Ø 27 mm | 1 |
| 23 | 9460 624 0801 | E-clip 8x1.3 | 1 |
| 24 | 0000 642 1216 | Rim sprocket 3/8" 8T | 1 |
| 24 | 0000 642 1216 | Rim sprocket 3/8" 8T option | 1 |
| 25 | 0000 642 1239 NLA | Rim sprocket 0.325" 9T option | 1 |
| 26 | 1128 640 2000 NLA | Chain sprocket 3/8" 7T Fitment / change note → option | 1 |
| 27 | 1128 640 2005 | Chain sprocket 3/8" 8T Fitment / change note → option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1128 160 2004 | Clutch | 1 |
| — | 1128 007 1001 | Rim sprocket kit 3/8" 8T Fitment / change note → | 1 |
| — | 1128 007 1001 | Rim sprocket kit 3/8" 8T Fitment / change note → option | 1 |
| — | 1128 007 1011 | Rim sprocket kit 0.325" 9T option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 046
046: sprocket options and market-dependent standard equipment
Seven- and eight-tooth 3/8-inch sprockets are separate options; only the starred seven-tooth entries may be standard in some markets.
- The bulletin says 046 can use the same cutting attachments as 044. It does not list every bar length, gauge or drive-link count, and does not waive matching the complete bar/chain/sprocket configuration.
- The asterisks apply only to the seven-tooth rim kit and seven-tooth spur sprocket: these may be standard equipment in some markets. Neither eight-tooth entry carries that remark.
- The repair-kit contents are not listed. No equivalence is inferred between the repair kit, sprocket kits and complete clutch assemblies.
Source: TI 46/1995, p. 5 · TI 46/1995, p. 7 — 1.10 and3: cutting attachment and user accessory roster.
Part numbers (6)
- 1128 900 5001 — 046 repair kitListed user accessory · 046; contents unspecified
- 1128 007 1000 — 3/8-inch seven-tooth rim sprocket kitStarred option · May be standard in some markets
- 1128 007 1001 — 3/8-inch eight-tooth rim sprocket kitUnstarred option · 046
- 1128 640 2000 — 3/8-inch seven-tooth spur sprocketStarred option · May be standard in some markets
- 1128 640 2005 — 3/8-inch eight-tooth spur sprocketUnstarred option · 046
- 0000 792 9132 — Chain scabbard extensionListed user accessory · 046
Service note · 046
046: engine fasteners and catalytic-muffler torque branches
Cylinder, crankcase, flywheel, clutch and muffler values retain thread and variant distinctions.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Cylinder/crankcase IS-M6×25: 15 Nm (11 lbf.ft); crankcase IS-M5×20: 11.5 Nm (8.5 lbf.ft); shroud/crankcase IS-M5×16: 7 Nm (5.2 lbf.ft).
- Standard muffler top IS-M5×6: 6.5 Nm (4.8 lbf.ft), Loctite 242; muffler/cylinder IS-M5×16: 11.5 Nm (8.5 lbf.ft), Loctite 242.
- Kat/catalytic muffler top IS-M5×30: 6.5 Nm (4.8 lbf.ft), Loctite 242; Kat muffler/cylinder IS-M6×18: 15 Nm (11 lbf.ft), Loctite 242. Separate muffler/crankcase IS-M6×18 row: 15 Nm (11 lbf.ft), with no adhesive remark printed.
- Flywheel M8×1 nut: 32.5 Nm (24 lbf.ft); clutch M12×1 L carrier: 50 Nm (37 lbf.ft), with left-hand thread explicitly marked L.
- Cylinder decompression valve M10×1: 14 Nm (10.3 lbf.ft), not the leakage-test plug; spark plug M14×1.25: 25 Nm (18.5 lbf.ft).
Source: TI 46/1995, p. 11 — 5.3: engine, exhaust and rotating assembly rows.
No additional parts-table entry added.
Service note · 046
046: small-fastener torques, adhesives and ignition washer
The ignition-module screws require both Loctite 242 and a washer; nearby screws have different requirements.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Generator IS-M4×12: 3.5 Nm (2.6 lbf.ft), Loctite 649. Chain-tensioner cover plate IS-M4×8: 3 Nm (2.2 lbf.ft).
- IS-M4×12 oil-pump cover at sprocket side: 3 Nm (2.2 lbf.ft); brake-band/crankcase: 3 Nm (2.2 lbf.ft), Loctite 242; oil pump: 3.5 Nm (2.6 lbf.ft).
- IS-M4×12 segment/fan housing: 2.5 Nm (1.8 lbf.ft); sprocket-side crankcase cover: 3 Nm (2.2 lbf.ft).
- M5 SK6 collar nut for carburetor/filter base/flange: 6 Nm (4.4 lbf.ft), remark 3/Loctite 270. The table calls the fastener a collar nut although its remark generically says screw; neither label is silently changed.
- Fan housing IS-M5×20: 7 Nm (5.2 lbf.ft). Ignition module/crankcase IS-M5×20: 7 Nm (5.2 lbf.ft), Loctite 242 AND a washer under the screw head. Do not transfer this washer requirement to every M5 screw.
Source: TI 46/1995, p. 11 — 5.3: M4 rows, intake collar nut, fan housing and ignition.
No additional parts-table entry added.
Service note · 046
046: limited 044 assembly inheritance, not blanket interchange
The release carries over clutch, rewind starter and chain brake from 044; other parts are described as revised.
- The source says 044 repair times also apply to 046, but gives no numeric times. Those allowances cannot be reconstructed from this page.
- Only clutch, rewind starter and chain brake are named as taken from 044. All other parts are described as revised/new and the reader is directed to the IPL. This is a release-level assembly statement, not proof that every internal part or later revision interchanges.
- The document is dated September 5,1995. That evidence date is not a serial changeover, production start for every market, or the 2026 review date.
Source: TI 46/1995, p. 12 — 5.4 and6: repair times and spare-parts scope.
No additional parts-table entry added.
Wrong number or missing part for the 046? Report a correction →