← 044/046 · MS 440/460/461

Stihl 1128 · Section B · 2 of 16 · 25 parts

Cylinder

Fits 046.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021344056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (25)

PosPart numberDescriptionQty
1 1128 020 1221 Cylinder with piston Ø 52 mm Fitment / change note → — 76.5 cc 1
1 1128 020 1217 NLA Cylinder with piston Ø 52 mm Fitment / change note → — 76.5 cc 1
2 1128 030 2009 Piston Ø 52 mm Fitment / change note → — 76.5 cc 1
3 1122 034 3000 Piston ring Ø 52x1.2 mm — 76.5 cc 2
4 1128 034 1501 Piston pin 12x8x35 1
5 9463 650 1200 Snap ring 12x1 2
6 9512 003 3061 Needle cage 12x15x15 1
7 1128 029 2304 Cylinder gasket 0.3 mm 1
8 1128 029 2306 NLA Cylinder gasket 0.8 mm 1
9 9022 341 1370 Spline screw IS-M6x30 Fitment / change note → 4
10 1128 020 9400 Decompression valve 1
11 1122 084 1405 Cover Fitment / change note → 1
12 1128 141 3200 Cooling plate 1
13 1125 149 0601 Muffler gasket 1
14 1128 141 2203 Manifold → replaced by 1128 141 2204 TI 46/2008 1
15 1128 141 2204 Manifold 1
16 9771 021 2578 Hose clip Ø 34x5 1
17 1110 400 7005 Spark plug Bosch WSR 6 F 1
17 0000 400 7000 Spark plug NGK BPMR7A 1
18 1128 084 1400 Cover 1
19 1128 405 1000 Spark plug boot 1
20 0000 998 0604 Torsion spring 1
21 1122 025 2200 Plug Fitment / change note → 1
40 9022 371 1350 Spline screw IS-M6x25 Fitment / change note → → replaced by 9022 341 1370 TI 3/1999 4
Not numbered on the diagram — assemblies, kits and options
— 1128 007 1052 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046: longer cylinder screws must not enter the old crankcase

The new crankcase has deeper tapped holes for M6×30 cylinder screws.

1 41 354 621 — 046 deeper cylinder-mounting holes and longer screws introduced.

  • Crankcase 1128 020 2116 → 1128 020 2118 uses M6×30 screws 9022 341 1370 instead of M6×25 screws 9022 371 1350.
  • Do not use the longer screws in original crankcase 1128 020 2116: they can bottom out without securing the cylinder.
  • The TI says four longer screws accompany the replacement case; this historical statement does not guarantee current package contents.
  • Remark 1 says original crankcase 1128 020 2116 was no longer available from the factory at the bulletin date. Remark 2 separately keeps original M6×25 screw 9022 371 1350 available as a spare for older machines; do not treat the short screw as universally obsolete.
  • The summary describes replacement crankcase item 5 as including stop buffer item 2 and bearings items 8 and 9. These historical replacement-case contents do not collapse the later AV and bearing production cutoffs into the screw-depth introduction.

Source: TI 3/1999, p. 2 · TI 3/1999, p. 3 — Sections 2.1 and 3: screw-depth prohibition.

Part numbers (4)
  • 1128 020 2116 — CrankcaseOriginal shallow-hole version · 046; do not use M6×30 screws
  • 1128 020 2118 — CrankcaseDeeper-hole version · 046 with M6×30 cylinder screws
  • 9022 371 1350 — M6×25 cylinder screwOriginal version · 046 original case
  • 9022 341 1370 — M6×30 cylinder screwRequired new-case screw · 046 deeper-hole case only

Conditional replacement · 046

046: piston/cylinder interchange works in one direction

The new piston is documented for old and new cylinders; the old piston is restricted to the old cylinder.

  • New piston 1128 030 2009 may be used in the previous and new cylinder versions. Old piston 1128 030 2004 must be used only in the previous cylinder, not the new one.
  • Cylinder-with-piston assembly: 1128 020 1217 → 1128 020 1221. The assembly number is not a bare-cylinder part number.
  • Introduction depends on handle variant: 046 flush handle from 1 46 085 314; 046 wrap handle from 1 46 086 124. No single model-wide cutoff is inferred.
  • Ring locating-pin positions changed for the wider intake port. The source says normal shop equipment cannot reliably measure the angle; identify the revision by its packaging part number.
  • TI44/2000 section 1 prints the uprated 046 output as 6.0 HP (4.5 kW). This is the bulletin’s historical configuration, not a universal model rating or a measured output of a repaired saw. Cylinder and piston optimization is described for both models; the filter-base revision is explicitly 046 only.
  • Summary item 3 is the cylinder-with-piston assembly including item 4, the separately listed piston. Do not treat the assembly number as a bare cylinder or add a second piston to its stated contents.
  • Remark 1 applies to both summary rows: the previous versions are no longer available from the factory at the time of this TI. This is not current stock information, a prohibition on the permitted old-cylinder combination, or permission to reverse the one-way piston interchange.
  • Drawing 145TI050 KN illustrates the two locating-pin angles marked a without giving numerical angles. The TI supplies no port-width dimensions, machining procedure or reliable visual measurement shortcut; packaging identification remains required.
  • The 6.0 HP / 4.5 kW pair is retained exactly as printed. No power percentage, conversion-based correction or transfer to earlier 046 C catalyst specifications is inferred.

Source: TI 44/2000, p. 1 · TI 44/2000, p. 2 — Complete sections 1–2: uprated engine, piston/cylinder service direction, 046 filter base, all summary rows and handle-specific cutoffs.

Part numbers (4)
  • 1128 020 1217 — Cylinder with pistonPrevious assembly · 046 previous cylinder version
  • 1128 020 1221 — Cylinder with pistonNew assembly · 046 new cylinder; old piston prohibited
  • 1128 030 2004 — PistonRestricted old version · 046 previous cylinder only
  • 1128 030 2009 — PistonNew version · 046 previous or new cylinder

Historical fitment · 046

046: close the decompression valve before using the locking strip

Locking strip 0000 893 5903 must not enter the spark-plug hole until the 046 decompression valve is closed.

  • The source warns that an open decompression valve may be bent by the force of the piston and locking strip. Closing the valve is an explicit prerequisite, not merely a starting instruction.
  • This is the 046 instruction from TI46/1995. Do not replace it with the separate 026 valve-removal instruction from TI31/1995, or generalize either rule to every model sharing a locking-strip or valve number.
  • This note does not give a complete locking or repair procedure, and does not establish the later MS460 procedure. It records source guidance, not a performed hardware operation.

Source: TI 46/1995, p. 9 — Section 5.1.1: complete locking-strip prerequisite.

Part numbers (1)
  • 0000 893 5903 — Locking stripCrankshaft locking service tool · 046 only with decompression valve closed

Historical fitment · 046

046: replace the decompression valve with a plug for leakage tests

Plug 1122 025 2200 must replace the decompression valve before the 046 leakage test.

  • The bulletin requires the plug in place of the decompression valve and refers to the service manual for the leakage test. The retained page alone is not a complete test procedure.
  • A standard deep-well 13-mm socket removes and installs the decompression valve. The stated 14 Nm (10.3 lbf.ft) is the decompression-valve tightening torque; it is not assigned here to the substitute plug or every 13-mm fastener.
  • Section 5.2.1.1 prints pressure 0.4 bar (5.8 psi) and vacuum 0.4 bar (5.8 psi); section 5.2.1.2 separately prints pressure 0.4 bar (5.8 psi). The original scan does not name the test object beside either subheading. Do not silently label one crankcase and the other carburetor, convert the printed vacuum magnitude into an absolute pressure, or infer dwell/leak limits.
  • Exact test-object mapping, apparatus configuration and acceptance limits require the version-appropriate service manual. No hardware test or safe bench readiness is implied.

Source: TI 46/1995, p. 10 — Sections 5.1.4 and 5.2: valve closure, valve torque and incompletely labeled test data.

Part numbers (1)
  • 1122 025 2200 — Cylinder plugRequired instead of decompression valve · 046 leakage-test closure; valve torque not assigned to this plug

Service note · 046

046: release the base gasket before lifting the cylinder

Separate the gasket from the cylinder base before taking the 046 cylinder off the piston.

  • The source specifies separating the gasket with a knife before lifting the cylinder, to avoid piston damage from snagging on the gasket edge. The illustration shows the base-gasket interface; it does not establish reuse of the gasket.
  • No gasket, cylinder or piston part number, replacement specification or fastener torque is supplied in this section. Do not promote a nearby catalog number into this source assertion.
  • This is a historical 046 service precaution, not a complete disassembly procedure or evidence of interchangeable 044/046 cylinders.

Source: TI 46/1995, p. 10 — Section 5.1.2: complete cylinder-removal precaution.

No additional parts-table entry added.

Historical fitment · 046

046: decompression valve and dust cover arrangement

Cover 1122 084 1405 sits between cylinder and shroud; the raised shroud opening protects the valve.

  • The valve body carries an axially moving conical plunger retained in either position by three spring-loaded balls. Pushing it down opens the passage for starting; ignition pressure raises the plunger and closes the passage.
  • The starting description is distinct from the closed-valve prerequisite for the locking strip. No valve opening pressure or valve part number is given here.
  • The shroud opening is raised to reduce accidental contact. The separate cover limits dirt entry; sharing this cover number does not establish cylinder or shroud interchangeability.

Source: TI 46/1995, p. 4 — 1.6: construction, operation and cover.

Part numbers (1)
  • 1122 084 1405 — Cover between cylinder and shroudDust-entry protection · 046 decompression opening

Service note · 046

046: original engine dimensions and construction

The 1995 046 specification is 76.5 cm³, 52 mm bore and 36 mm stroke; it is not a 044 interchange claim.

  • Compared with 044, the bulletin describes a wider big-end bearing, stronger crankcase, revised intake flange/baffle, cylinder cooling area increased by 10%, modified shroud/outlet plate and redesigned vibration buffers. No replacement numbers or retrofit permission are given.
  • The composite flywheel uses a steel hub, polymer fan, high-power magnets and magnesium starter-pawl bushing. Claimed weight reduction is about 30%, with cooling-air flow increased by 30%; these are source comparisons, not measurements made by this project.
  • The cylinder/crankcase uses 6 mm mounting screws and a sheet-steel gasket. The engine is a single-cylinder two-stroke with specially impregnated bore; compression ratio 9.6: 1. Three-part drop-forged crankshaft, two deep-groove main bearings, needle-cage big and small ends, 62 mm connecting rod and 12 mm piston pin are specified.
  • Rated power is 4.4 kW (5.9 bhp) at 9,500 rpm; maximum torque is 4.8 Nm (3.54 lb.ft) at 6,500 rpm. Maximum permissible speed is 13,500 rpm WITH Rollomatic bar and chain, not an unloaded powerhead test limit. Mean idle is 2,500 rpm.
  • The unlined centrifugal clutch is 76 mm diameter and engages at approximately 3,500 rpm. The ElastoStart rewind mechanism uses pawl engagement and 3.5 mm starter rope.
  • Powerhead weight excluding cutting attachment is 6.5 kg (14.3 lb). The page separately prints power-to-weight ratio 2.55 lbs/bhp; this does not agree with the printed 14.3 lb and 5.9 bhp (about 2.42). Preserve the discrepancy, not a silently recalculated replacement.
  • Specifications describe this historical 046 release; they do not identify all later 046/MS 460 variants or establish interchangeable engine, flywheel or AV parts.

Source: TI 46/1995, p. 1 · TI 46/1995, p. 3 · TI 46/1995, p. 5 · TI 46/1995, p. 6 · TI 46/1995, p. 7 — 1.3–1.5,1.8–1.9,1.11,2.1,2.4: original construction and specifications.

No additional parts-table entry added.

Historical fitment · 046

046: leakage-test and piston tool applications

The service roster distinguishes exhaust sealing, test flange, crankcase vacuum equipment and piston assembly tools.

  • Tool applications are a roster, not a test sequence. The decompression valve must be closed for locking-strip use and replaced by the specified plug for leakage testing. The unlabeled test-object headings on page 10 remain unresolved.
  • The vacuum pump is listed for crankcase leakage; the combined tester is listed for carburetor and crankcase leakage. That tool distinction does not recover the missing page 10 test-object labels.
  • The sleeves appear under the test flange; nipple and fuel line appear under the vacuum pump. No quantity or universal hose substitution is inferred. Installing tool 12 is specifically for hookless piston snap rings.

Source: TI 46/1995, p. 7 · TI 46/1995, p. 8 · TI 46/1995, p. 9 · TI 46/1995, p. 10 — 4.1 and5.1: leakage and piston tools with prerequisites.

Part numbers (13)
  • 0000 893 5903 — Locking strip; crankshaft blocking with valve closedListed tool application · 046
  • 0000 855 8106 — Exhaust sealing plateListed tool application · 046
  • 1108 893 4800 — Wooden piston assembly blockListed tool application · 046
  • 0000 893 2600 — Piston-ring clamping strapListed tool application · 046
  • 1128 850 4200 — Leak-test flangeListed tool application · 046
  • 0000 963 1008 — Test-flange sleevesListed tool application · 046
  • 1106 850 2905 — Carburetor and crankcase testerListed tool application · 046
  • 0000 850 3501 — Crankcase vacuum pumpListed tool application · 046
  • 0000 855 9200 — Vacuum-pump nippleListed tool application · 046
  • 1110 141 8600 — Vacuum-pump fuel lineListed tool application · 046
  • 1122 025 2200 — Plug in place of decompression valveListed tool application · 046
  • 1111 893 4700 — Piston-pin assembly driftListed tool application · 046
  • 5910 890 2212 — Installing tool 12 for hookless snap ringsListed tool application · 046

Service note · 046

046: engine fasteners and catalytic-muffler torque branches

Cylinder, crankcase, flywheel, clutch and muffler values retain thread and variant distinctions.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Cylinder/crankcase IS-M6×25: 15 Nm (11 lbf.ft); crankcase IS-M5×20: 11.5 Nm (8.5 lbf.ft); shroud/crankcase IS-M5×16: 7 Nm (5.2 lbf.ft).
  • Standard muffler top IS-M5×6: 6.5 Nm (4.8 lbf.ft), Loctite 242; muffler/cylinder IS-M5×16: 11.5 Nm (8.5 lbf.ft), Loctite 242.
  • Kat/catalytic muffler top IS-M5×30: 6.5 Nm (4.8 lbf.ft), Loctite 242; Kat muffler/cylinder IS-M6×18: 15 Nm (11 lbf.ft), Loctite 242. Separate muffler/crankcase IS-M6×18 row: 15 Nm (11 lbf.ft), with no adhesive remark printed.
  • Flywheel M8×1 nut: 32.5 Nm (24 lbf.ft); clutch M12×1 L carrier: 50 Nm (37 lbf.ft), with left-hand thread explicitly marked L.
  • Cylinder decompression valve M10×1: 14 Nm (10.3 lbf.ft), not the leakage-test plug; spark plug M14×1.25: 25 Nm (18.5 lbf.ft).

Source: TI 46/1995, p. 11 — 5.3: engine, exhaust and rotating assembly rows.

No additional parts-table entry added.

Wrong number or missing part for the 046? Report a correction →