← 044/046 · MS 440/460/461

Stihl 1128 · Section K · 10 of 16 · 32 parts

AV system

Fits 046.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425263444404141425667789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 1128 791 8401 Ring 1
2 1128 791 8400 Ring 1
3 1122 790 9905 Annular buffer 1122/05 1
4 9074 478 4435 Pan head self-tapping screw IS-P6x19 3
5 1122 791 7301 Plug 1
6 1121 790 9904 Annular buffer 2
6 1125 790 9906 Annular buffer 1125/06 2
7 1125 791 7306 Plug 2
8 1128 790 9909 Annular buffer 1
8 1128 790 9908 Annular buffer 1
9 9416 868 5630 Hollow rivet 5.5x0.5x6.8 2
10 9022 313 0680 Spline screw IS-M4x16 2
11 1128 791 7200 Sleeve 1
12 1128 792 8500 Hose 1
13 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 1
14 1125 790 9910 Annular buffer 1125/10 1
15 1125 790 9904 Annular buffer 1125/04 1
16 1128 790 9911 Annular buffer 1
17 1133 791 5900 Stop buffer 1
18 1128 141 8600 Impulse hose 1
19 1110 145 9001 Plug Fitment / change note → 1
20 1117 141 1800 Sleeve 1
21 1128 121 8600 Washer 1
22 1128 120 0624 Carburetor HD-14B 1
22 1128 120 0626 Carburetor HD-24C 1
23 1128 120 0623 Carburetor HD-16B 1
24 1128 121 7000 Baffle 1
25 1128 182 0700 Grommet 1
26 1128 123 7502 Grommet 1
40 1128 790 9908 Annular buffer 1
41 1125 790 9906 Annular buffer 1125/06 2
42 not sold separately Carburetor HD-9A 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046: AV stop openings are a separate change

TI 03/1999 separates the AV stop changes from the earlier 046 deep-thread crankcase introduction.

1 41 628 724 — 046 AV change, distinct from crankcase screw-depth and bearing changes.

  • AV changes from 1 41 628 724 add crankcase stop buffer 1125 791 2810 and tank plug 1110 145 9001 in the provided openings. Insert the crankcase stop from the tank-housing side.
  • Tank housing 1128 350 0809 → 1128 350 0812 is assigned to this AV cutoff.
  • Crankcase 1128 020 2118 was already introduced for deeper cylinder screw holes at a different earlier cutoff. Its number alone must not be used as proof of the later AV opening.
  • The summary lists tank housing item 10 including plug item 4. Remark 1 says original tank housing 1128 350 0809 was no longer available from the factory at the bulletin date; this is not a current stock claim.
  • The summary describes replacement crankcase item 5 as including stop buffer item 2 and both bearings (items 8 and 9), although its introduction row uses the earlier 1 41 354 621 cutoff. This replacement-supply description does not prove that every production crankcase at that earlier serial had the later AV opening or optimized bearings.
  • The AV introduction also says annular buffers were modified without identifying a separate numbered or dimensional annular-buffer revision.

Source: TI 3/1999, p. 1 · TI 3/1999, p. 2 · TI 3/1999, p. 3 — Sections 1–3: separate AV and case introductions.

Part numbers (5)
  • 1128 350 0809 — Tank housingOriginal version · 046
  • 1128 350 0812 — Tank housingModified AV version · 046 with plug opening
  • 1125 791 2810 — Stop bufferAV component · 046 crankcase with provided opening
  • 1110 145 9001 — Plug / stop bufferAV component · 046 modified tank housing
  • 1128 020 2118 — CrankcaseNumber shared across staged changes · 046; inspect AV opening and screw-depth revision

Service note · 046

046: original engine dimensions and construction

The 1995 046 specification is 76.5 cm³, 52 mm bore and 36 mm stroke; it is not a 044 interchange claim.

  • Compared with 044, the bulletin describes a wider big-end bearing, stronger crankcase, revised intake flange/baffle, cylinder cooling area increased by 10%, modified shroud/outlet plate and redesigned vibration buffers. No replacement numbers or retrofit permission are given.
  • The composite flywheel uses a steel hub, polymer fan, high-power magnets and magnesium starter-pawl bushing. Claimed weight reduction is about 30%, with cooling-air flow increased by 30%; these are source comparisons, not measurements made by this project.
  • The cylinder/crankcase uses 6 mm mounting screws and a sheet-steel gasket. The engine is a single-cylinder two-stroke with specially impregnated bore; compression ratio 9.6: 1. Three-part drop-forged crankshaft, two deep-groove main bearings, needle-cage big and small ends, 62 mm connecting rod and 12 mm piston pin are specified.
  • Rated power is 4.4 kW (5.9 bhp) at 9,500 rpm; maximum torque is 4.8 Nm (3.54 lb.ft) at 6,500 rpm. Maximum permissible speed is 13,500 rpm WITH Rollomatic bar and chain, not an unloaded powerhead test limit. Mean idle is 2,500 rpm.
  • The unlined centrifugal clutch is 76 mm diameter and engages at approximately 3,500 rpm. The ElastoStart rewind mechanism uses pawl engagement and 3.5 mm starter rope.
  • Powerhead weight excluding cutting attachment is 6.5 kg (14.3 lb). The page separately prints power-to-weight ratio 2.55 lbs/bhp; this does not agree with the printed 14.3 lb and 5.9 bhp (about 2.42). Preserve the discrepancy, not a silently recalculated replacement.
  • Specifications describe this historical 046 release; they do not identify all later 046/MS 460 variants or establish interchangeable engine, flywheel or AV parts.

Source: TI 46/1995, p. 1 · TI 46/1995, p. 3 · TI 46/1995, p. 5 · TI 46/1995, p. 6 · TI 46/1995, p. 7 — 1.3–1.5,1.8–1.9,1.11,2.1,2.4: original construction and specifications.

No additional parts-table entry added.

Service note · 046

046: handle, buffer and cutting-attachment fastener torques

Handle, AV-buffer, bumper and chain-catcher rows keep distinct torques even when thread sizes match.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Switch housing B2.9×9.5: 1 Nm (0.75 lbf.ft); handle molding B3.9×19: 1.6 Nm (1.2 lbf.ft). Buffer/crankcase IS-M4×16: 5 Nm (3.7 lbf.ft), Loctite 242.
  • Spiked bumper top with nut IS-M5×12: 7.5 Nm (5.5 lbf.ft); bottom bumper/chain catcher IS-M5×16: 7.5 Nm (5.5 lbf.ft).
  • Wrap-around handle with bracket IS-M5×20: 7 Nm (5.2 lbf.ft); left hand guard IS-M5×30: 7 Nm (5.2 lbf.ft).
  • Front handle top/bottom IS-P6×19: 8 Nm (5.9 lbf.ft), Loctite 649. Front and rear buffer/tank-housing IS-P6×19: 5.5 Nm (4 lbf.ft); rear-left buffer/tank-housing IS-P6×32.5: 5.5 Nm (4 lbf.ft). Reuse the existing Plastoform thread as page 12 directs.
  • Self-locking M5 nut for spiked bumper: 7.5 Nm (5.5 lbf.ft); self-locking M5 nut for chain catcher/spiked bumper: 6 Nm (4.4 lbf.ft). These are separate rows, not interchangeable tightening values.
  • The guide-bar collar-nut row prints M8×21.5,23 Nm (17 lbf.ft), remark 2/Loctite 242. That unusual adhesive assignment is retained as printed, not generalized to all bar nuts or silently removed; verify the exact repair context before applying it.

Source: TI 46/1995, p. 11 · TI 46/1995, p. 12 — 5.3: handles, buffers, bumper, guard and guide-bar rows.

No additional parts-table entry added.

Wrong number or missing part for the 046? Report a correction →