← 044/046 · MS 440/460/461

Stihl 1128 · Section L · 11 of 16 · 47 parts

Carburetor HD-14B, HD-16B, HD-24C

Fits 046.

Parts diagrams →

Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526272829293303133343434343535363738394404142424356789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (47)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 4116 121 5000 Inlet control lever 1
3 1128 122 3002 Spring 1
4 1113 121 9200 Spindle 1
5 1114 122 7400 Round head screw 1
6 4117 122 9402 Plug 1
7 1128 121 5405 Valve jet 1
8 1128 121 5602 Fixed jet 0.70 Fitment / change note → → replaced by 1128 121 5603 TI 47/1997 1
9 1128 129 0906 Gasket 1
10 4116 121 4700 Metering diaphragm 1
11 1128 121 0801 End cover 1
12 1121 122 7101 Screw 4
13 1114 121 7800 Strainer 1
14 4116 121 4800 Pump diaphragm 1
15 4116 129 0902 Gasket 1
16 1127 122 3205 Torsion spring 1
17 1127 120 7100 Throttle shaft with lever 1
18 1117 122 9000 E-clip 1
19 1128 121 3302 Throttle shutter 1
19 1128 121 3303 Throttle shutter 1
20 1115 122 7400 Round head screw 1
21 1127 122 3200 Torsion spring 1
22 1127 120 7200 Choke shaft with lever 1
23 1123 122 9000 E-clip 1
24 1122 121 2900 Choke shutter 1
25 1110 122 7400 Round head screw 1
26 1127 122 6200 Idle speed adjustment screw 1
27 1127 121 0800 End cover 1
28 1114 122 7100 Screw 1
29 1128 122 3003 Spring Fitment / change note → 2
30 1127 122 6701 High speed adjustment screw Fitment / change note → 1
31 1128 122 6805 Low speed adjustment screw → replaced by 1128 122 6807 TI 35/1999 1
33 1128 122 6804 Low speed adjustment screw Fitment / change note → → replaced by 1128 122 6806 TI 35/1999 1
34 4203 122 3600 Sealing ring 1
35 4203 121 2700 Cap Fitment / change note → 2
36 1128 121 5603 Fixed jet 0.68 Fitment / change note → 1
37 1128 129 1100 Gasket 1
38 1128 430 6002 Heating element 1
39 1118 431 6600 NLA Terminal pin no longer available from factory 1
40 1118 431 6700 NLA Terminal socket no longer available from factory 1
41 1124 121 9100 Bushing 1
42 1128 121 5605 Fixed jet 0.66 Fitment / change note → option 1
43 1128 121 5604 Fixed jet 0.76 1
Not numbered on the diagram — assemblies, kits and options
— 1128 120 0624 Carburetor HD-14B Fitment / change note → 1
— 1128 120 0623 Carburetor HD-16B Fitment / change note → 1
— 1128 120 0626 Carburetor HD-24C 1
— 1128 007 1066 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046: carburetor replacement depends on equipment

TI 47/1997 distinguishes HD-14 service replacements for older non-EPA machines from HD-16 carburetors for the EPA-equipped version.

  • Older 046 without EPA equipment: replace HD-8A (1128 120 0610) with HD-14 (1128 120 0624).
  • The EPA-equipped 046 uses HD-16 (1128 120 0623). Do not treat the two replacement branches as unconditional substitutes.
  • The source requires new limiter caps after removal during repair; adjustment and cap-fitting procedure remains in the TI, not inferred from a parts match.
  • Introduction is stated as the start of EPA-version production, with no numeric serial cutoff.
  • Except for limiter caps and adjusting screws, the non-EPA service HD-14 is stated to be technically the same as its EPA counterpart HD-16; this does not remove the equipment-dependent replacement rule.
  • The summary lists original HD-8A with items 7, 9, 10 and 12; new HD-14 includes 7, 9, 10, 12, 14 and 15; EPA HD-16 includes 8, 9, 11, 13 to 16. These are printed inclusion lists, not permission to infer omitted items.
  • Original complete carburetor no longer available from the factory; all other parts remain as before. These are dated 1997 supply statements, not current stock. The separate cap-setting notes retain lean-stop versus screw-seat reference points.

Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 · TI 47/1997, p. 5 — Sections 1–1.7: carburetor and service branches; full section, drawing and summary context reviewed in batch26.

Part numbers (3)
  • 1128 120 0610 — Carburetor HD-8AOriginal equipment · 046 original configuration
  • 1128 120 0624 — Carburetor HD-14Conditional service replacement · 046 older machine without EPA equipment
  • 1128 120 0623 — Carburetor HD-16EPA configuration · 046 EPA-equipped version only

Conditional replacement · 044 / 046

044 / 046: valve-jet revision in the 1997 carburetor change

TI 47/1997 changes valve jet 1128 121 5403 to 1128 121 5404 in the described HD carburetor revision.

  • Applies to the described HD-15/HD-17 (044) and HD-14/HD-16 (046) configurations, not every carburetor fitted to these models.
  • The previous valve jet remains available as a spare in the source table. A table revision is not permission to mix all other old/new carburetor components.
  • The bulletin attributes the valve-jet change to optimized part-load behavior and reduced fuel consumption; these are manufacturer claims, not measured results. Diagram139TI015 identifies valve jet(1) separately from fixed jet(2).
  • O-rings on both adjusting screws improve sealing against secondary air. Knurled screw heads retain the limiter caps; molded stops in the insert bores limit cap travel. Diagram139TI011 defines items1–5; its visible item6 is not defined by the printed legend, so no component identity is invented.

Source: TI 47/1997, p. 2 · TI 47/1997, p. 5 — Sections 1 and 1.7: valve jet; full section, drawing and summary context reviewed in batch26.

Part numbers (2)
  • 1128 121 5403 — Valve jetPrevious version · 044 / 046 described HD carburetors
  • 1128 121 5404 — Valve jetRevised version · 044 HD-15/HD-17 and 046 HD-14/HD-16 change

Conditional replacement · 046

046: HD-16 uses jet 68; HD-14 retains jet 70

The 046 EPA HD-16 and non-EPA HD-14 use different fixed jets in the 1997 table.

  • HD-16 EPA includes item 8: jet 68 (1128 121 5603). HD-14 service carburetor includes item 7: jet 70 (1128 121 5602).
  • Do not apply the HD-16 jet change to HD-14 or to 044 merely because the parts share a bulletin.
  • The original jet 70 remains available as a spare; this is configuration selection, not universal supersession.

Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 · TI 47/1997, p. 5 — Sections 1, 1.2 and 1.7: fixed jet and carburetor inclusions.

Part numbers (2)
  • 1128 121 5602 — Fixed jet 70Non-EPA configuration · 046 HD-14; also original HD-8A table
  • 1128 121 5603 — Fixed jet 68EPA configuration · 046 HD-16 only in this change

Conditional replacement · 046

046: non-EPA carburetor screw and spring revisions

The service carburetor has its own adjusting screws and springs, distinct from the EPA screw/cap configuration.

  • Applies to HD-14 service carburetor for older 046 without EPA equipment, not HD-16 EPA.
  • Low-speed screw: 4116 122 6800 → 1128 122 6803. High-speed screw: 1127 122 6700 → 1127 122 6701. Two springs: 4116 122 3001 → 1128 122 3003.
  • The new service carburetor includes sealing rings (item 15), but the bulletin gives no separate order number for them.
  • Previous screws and springs remain available as spares. This record does not authorize fitting non-EPA screws to an EPA carburetor.
  • The summary specifies two sealing rings and explicitly marks them unavailable as separate items, not merely lacking a printed order number. Adjusting-screw O-rings seal against the carburetor body. Introduction is from the start of EPA-version production; all other parts remain as before.

Source: TI 47/1997, p. 2 · TI 47/1997, p. 5 — Sections 1.2 and 1.7: non-EPA carburetor subparts; full section, drawing and summary context reviewed in batch26.

Part numbers (6)
  • 4116 122 6800 — Low-speed screwPrevious version · 046 original non-EPA HD configuration
  • 1128 122 6803 — Low-speed screwRevised non-EPA version · 046 HD-14
  • 1127 122 6700 — High-speed screwPrevious version · 046 original non-EPA HD configuration
  • 1127 122 6701 — High-speed screwRevised non-EPA version · 046 HD-14
  • 4116 122 3001 — SpringPrevious version · 046 original non-EPA HD configuration
  • 1128 122 3003 — SpringRevised version; two · 046 HD-14

Conditional replacement · 046

046: EPA screws require new limiter caps after servicing

EPA adjusting screws and caps form a distinct configuration; removed caps must not be reused.

  • HD-16 EPA uses low-speed screw 1128 122 6804, high-speed screw 1128 122 6703 and two caps 4203 121 2700.
  • After repair and specified adjustment, fit new limiter caps. Removed caps must not be reused.
  • The table includes two springs 1128 122 3003 and sealing rings; the rings are not available separately in this bulletin.
  • Do not substitute the non-EPA screw set. This parts note is not a standalone carburetor adjustment procedure.
  • The summary specifies two sealing rings and explicitly marks them unavailable as separate items, not merely lacking a printed order number. Adjusting-screw O-rings seal against the carburetor body. Introduction is from the start of EPA-version production; all other parts remain as before.

Source: TI 47/1997, p. 2 · TI 47/1997, p. 5 — Sections 1–1.7: EPA screws and limiter caps; full section, drawing and summary context reviewed in batch26.

Part numbers (4)
  • 1128 122 6804 — EPA low-speed screwEPA configuration · 046 HD-16
  • 1128 122 6703 — EPA high-speed screwEPA configuration · 046 HD-16
  • 4203 121 2700 — Limiter capRequired new caps; two · 046 HD-16 after servicing
  • 1128 122 3003 — SpringConfiguration component; two · 046 HD-16

Historical fitment · 046

046: optional high-altitude jet for HD-14 / HD-16

TI 29/1998 lists the optional 0.66 mm jet by stamped carburetor type; this is not the standard jet or a universal replacement.

  • Select by the type stamped on the carburetor body, not the saw model or assembly part number alone. The cited rows name HD-14 and HD-16 without later revision suffixes.
  • Optional jet 1128 121 5605 has a 0.66 mm bore. The source restricts the smaller-bore option to very high altitude when the normal adjustment range is insufficient.
  • Do not use the smaller-bore high-altitude jet at lower altitudes: the source warns of an overly lean mixture and engine damage. No universal altitude threshold is supplied.
  • Replacement is for trained personnel; press-fit positioning depends on the separate Carburetors handbook. This lookup is not a complete installation or adjustment procedure.
  • The scan table has no USA-only asterisk on these rows. This does not establish universal regulatory approval or applicability to later carburetor suffixes.
  • This bulletin does not establish the missing HD-15 to HD-15 A revision or override later variant-specific instructions.

Source: TI 29/1998, p. 1 · TI 29/1998, p. 2 — Important notes and table: HD-14 / HD-16 rows.

Part numbers (3)
  • 1128 120 0624 — Carburetor HD-14Source type association · 046; stamped HD-14 only
  • 1128 120 0623 — Carburetor HD-16Source type association · 046; stamped HD-16 only
  • 1128 121 5605 — High-altitude fixed jet, 0.66 mmOptional, not standard · HD-14 / HD-16; high-altitude conditions only

Service note · 046

046: historical carburetor and ignition specifications

The original fuel and ignition settings are release-specific reference data, not universal replacement-carburetor settings.

  • The original all-position diaphragm carburetor has an integral fuel pump; standard H and L settings are each one turn open. No carburetor type or limiter configuration is specified, so these settings are not assigned to every carburetor listed on the linked later IPL sheets.
  • Fuel capacity is 0.94 l (2 US pt). The 1995 source specifies minimum pump octane 89 unleaded, 50: 1 with STIHL 50: 1 two-stroke oil, and 25: 1 with other brand-name air-cooled two-stroke oils. This is historical formulation-dependent guidance, not a new recommendation for current oils.
  • Breakerless electronic magneto ignition: module/flywheel air gap 0.15–0.30 mm (0.006–0.012 in), timing 2.0–3.0 mm (0.080–0.12 in) before top dead center.
  • Suppressed Bosch WSR 6 F spark plug: 0.5 mm (0.020 in) electrode gap, M14 × 1.25 thread, 9.5 mm (0.37 in) thread length and printed heat range 200. No alternative plug or STIHL part number is inferred.

Source: TI 46/1995, p. 6 · TI 46/1995, p. 7 — 2.2–2.3: fuel, ignition and spark-plug specification.

No additional parts-table entry added.

Service note · 046

046 C: catalyst fuel and speed limits

Accurate tachometer required; full-throttle limits are 13,000–13,500 rpm.

  • For the 046 C catalytic-converter version, corrections to high-speed screw H are permitted only with an accurate tachometer to check that maximum permissible engine speed 13,500 rpm is not exceeded, with a properly tensioned chain. Minimum full-throttle speed must not be below 13,000 rpm. These are not idle-speed specifications or verified measurements.
  • The printed fuel requirement is unleaded brand-name gasoline mixed with STIHL 50:1 high-performance two-stroke engine oil or STIHL HT plus 50:1 synthetic engine oil. This records the 1997 catalyst-version instruction, not a new fuel recommendation for every 046 or successor.
  • The source also refers to TI11/1993 section1.5, absent from the retained corpus. The locally printed requirement is retained without inventing that missing section. Linked carburetor sheets are navigation aids, not proof that every carburetor variant fits 046 C.

Source: TI 5/1997, p. 2 — Complete sections1.2–1.3.

No additional parts-table entry added.

Service note · 044 / 046

044 / 046 EPA: capped standard setting

H = 3/4 and L = 1/4 open from the lean stop; not from screw seats.

  • This note applies to the described EPA HD-17(044) and HD-16(046) carburetors with limiter caps. Factory optimum setting is the standard setting: H = 3/4 turn and L = 1/4 turn open, starting from the lean stop in each case. It is not the uncapped basic setting and not a setting for every HD carburetor.
  • The integral stops in the insert bores limit corrections to 270 degrees. Caps are retained by the knurled screw heads and sit flush with the insert, at the bottom of the dome. The source describes this range as permitting high-altitude leaning while limiting enrichment beyond its EPA limits.
  • For unsatisfactory high-altitude running, the printed sequence is check standard setting, warm engine, then slight clockwise(leaner) corrections of H and L. Too lean a setting exceeds maximum permissible speed and risks engine damage. No numeric maximum speed or altitude threshold is printed here; no value is borrowed from the046 C catalyst instruction.

Source: TI 47/1997, p. 2 · TI 47/1997, p. 3 — Complete sections1.1–1.3 and cap-stop diagram132TI022.

No additional parts-table entry added.

Service note · 044 / 046

044 / 046 EPA: cap removal and basic setting

Uncapped H and L each start one full turn open from their seats.

  • Applies to the described EPA HD-17(044) and HD-16(046) configuration, not every carburetor on these model sheets. Remove caps to replace screws or clean the carburetor. First turn the caps/screws counterclockwise to their stops, then screw puller5910 890 4500 into each cap counterclockwise until it comes off. Do not reuse removed caps.
  • After fitting adjusting screws and with caps removed, start with screws against their seats: open H one full turn and L one full turn. This seat-referenced basic setting must not be confused with the capped standard setting measured from lean stops.
  • Always fit new caps. Insert with lug positions exactly as drawing132TI023, then push onto screws until flush with insert(1). The source says the resulting position equals the standard setting, but prints cross-reference1.2 where the standard-setting section is1.3. Preserve this reference mismatch; the source drawing remains the lug-orientation reference.
  • Set idle speed to2500 rpm with idle-speed screw LA and use a tachometer. This is not the maximum permissible engine speed. This historical procedure does not authorize unattended adjustment or hardware operation.

Source: TI 47/1997, p. 3 · TI 47/1997, p. 4 — Complete sections1.2,1.4–1.4.3; diagrams139TI013 and132TI023.

Part numbers (1)
  • 5910 890 4500 — Limiter-cap pullerSpecified service tool · 044 HD-17 /046 HD-16 EPA cap removal

Service note · 044 / 046

044 / 046: EPA label and 50:1 approval context

The1997 approval used50:1; referenced TI27/1997 remains unavailable in this corpus.

  • The cover states that the described modifications achieve EPA compliance except sections4.2,5.2 and6.1. There is no body subsection6.1 in this issue: front hand guard is section6 and flush-cut version is7.1. The exception label remains unresolved; do not silently assign an emission role to either change.
  • The illustrated factory IMPORTANT ENGINE INFORMATION label states conformity to US EPA Phase1 utility/lawn-and-garden engine regulations and refers to the owner manual for maintenance specifications and adjustment. Its engine-family/type/displacement/date fields are an example, not an observed machine identity or evidence that any repaired machine is compliant.
  • Section1.5 says EPA approval was obtained with50:1 fuel/oil mix and no emission measurements are available for other ratios. This is the scope of the original approval evidence, not a claim that alternate ratios were tested or a universal fuel recommendation.
  • Cover and sections1.5–1.6 refer to TI27/1997, including Federal Emission Control Systems Utility Engines. TI27/1997 is absent from the retained690-TI inventory and tipages scan filenames; that referenced detail remains a source gap, not proof of absence everywhere.

Source: TI 47/1997, p. 1 · TI 47/1997, p. 4 — Cover compliance statement/label and complete sections1.5–1.6.

No additional parts-table entry added.

Wrong number or missing part for the 046? Report a correction →