Stihl 1128 · Section J · 9 of 16 · 40 parts
Tank housing
Fits 046.
Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 350 0845 | Tank housing | 1 |
| 2 | 1128 122 6603 | Collar screw | 2 |
| 3 | 1128 358 7703 | Hose | 1 |
| 4 | 0000 350 5800 | Tank vent Fitment / change note → → replaced by 0000 350 5804 TI 41/2003 | 1 |
| 5 | not sold separately | O-ring not available as a separate item | 1 |
| 6 | 1128 656 1500 | Guard | 1 |
| 7 | 9099 021 2770 | Self-tapping screw 3.9x13 | 1 |
| 8 | 0000 967 3662 | Warning pictogram MS | 1 |
| 9 | 1128 180 0910 | Switch shaft Fitment / change note → | 1 |
| 10 | 0000 997 0227 | Compression spring | 1 |
| 11 | 1128 182 1700 | Slide control | 1 |
| 12 | 1128 180 3501 | Switch housing | 1 |
| 13 | 1128 442 1600 | Contact spring | 1 |
| 14 | 1128 442 1601 | Contact spring | 1 |
| 15 | 9099 021 1760 | Self-tapping screw 2.9x9.5 | 1 |
| 16 | 0000 350 3504 | Pickup body | 1 |
| 17 | 0000 350 0525 | Filler cap Fitment / change note → | 1 |
| 18 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 19 | 1128 182 1005 | Throttle trigger | 1 |
| 20 | 1128 182 1500 | Throttle rod | 1 |
| 21 | 1117 182 4500 | Torsion spring | 1 |
| 22 | 9371 470 2640 | Cylindrical pin 5x24 | 1 |
| 23 | 1117 182 0805 | Lockout lever | 1 |
| 24 | 1128 791 0600 | Handle molding | 1 |
| 25 | 9074 478 3076 | Pan head self-tapping screw IS-P4x19 | 1 |
| 26 | 0000 967 3605 | Warning pictogram Filler cap | 1 |
| 27 | 0000 967 3405 | Instruction label no longer available from factory | 1 |
| 28 | 0000 967 3500 NLA | Instruction label | 1 |
| 28 | 0000 967 3685 | Instruction label not illustrated | 1 |
| 32 | 1122 358 1800 | Filter Fitment / change note → | 1 |
| 33 | 1128 350 5802 | Tank vent Fitment / change note → → replaced by 0000 350 5800, 0000 350 5800 TI 5/2001 | 1 |
| 34 | 0000 350 0520 | Filler cap Fitment / change note → → replaced by 1127 350 0500 TI 48/1995 | 1 |
| 35 | 0000 359 1220 | Sealing ring | 1 |
| 36 | 0000 350 0900 | Rope | 1 |
| 37 | 1121 358 1800 | Filter Fitment / change note → → replaced by 1122 358 1800 TI 31/2000 | 1 |
| 38 | 1121 358 2500 | Cap Fitment / change note → | 1 |
| 39 | 1122 350 5851 NLA | Tank vent Fitment / change note → | 1 |
| 40 | 1128 353 1600 | Valve Fitment / change note → | 1 |
| 41 | 1121 442 0400 | Hose no longer available from factory | 1 |
| 42 | 0000 967 3692 | Warning pictogram Filler cap | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
IPL correction · 044 / 046
Switch shaft: 044 and 046 differ
The original switch shaft can be used in the 044, but the 046 requires the newer wedge-lever shaft.
- 1128 180 0900 is permitted in the 044, not in the 046.
- 1128 180 0910 is documented for both 044 and 046. The 046 used it from launch; the 044 change was in progress, with no serial cutoff supplied.
- The drawing labels original lever section A and new wedge-shaped choke-operating lever section B. These are shape identifiers, not part-order suffixes or installation dimensions.
- Original shaft 1128 180 0900 is deleted and no longer available from the factory in the summary. Existing stock may be used up in 044 only; the new 046 shaft was fitted from market launch despite the erroneous parts-list information. Historical deletion does not prohibit the explicitly allowed 044 use-up.
Source: TI 5/1996, p. 1 — Section 1: Switch shaft and service notes.
Part numbers (2)
- 1128 180 0900 — Switch shaftOriginal / restricted · 044 only; explicitly excluded for 046
- 1128 180 0910 — Switch shaftCorrected / new version · 044 and 046
Historical fitment · 046
046 tank valve: unchanged housing number
Tank housing 1128 350 0806 retained its number when valve 4114 353 1600 changed to 1128 353 1600.
Later reviewed guidance: 046: revised tank housing and inward-only valve
X 33 986 053 — New valve introduced in the specified 046 tank housing.
- This change applies to the 046 section of TI 25/1996; its shared 044/046 header does not make this a 044 valve change.
- New valve introduced from X 33 986 053. The TI identifies it by fully separated sealing lips and a white dot.
- The unchanged tank-housing number alone cannot identify which valve version is installed.
- Original valve sealing lips are joined at their ends; the new lips are separated over their whole width. The source claims easier tank air admission and improved starting behavior, not a measured project result.
- The tank-housing summary includes the valve as item2. Only the modified housing is supplied from the factory. The original valve remains a spare for other models, without a named other-model list; that is not approval to install it in the revised046 configuration. These are historical availability statements, not current stock.
Source: TI 25/1996, p. 1 — Complete section1: both valve drawings, tank/valve inclusion, changeover and both availability remarks.
Part numbers (3)
- 1128 350 0806 — Tank housingSame number, modified contents · 046 tank housing; inspect valve version
- 4114 353 1600 — Tank valveOriginal equipment · 046 before this change; later supply for other models is not 046 fitment
- 1128 353 1600 — Tank valveNew version · 046 modified tank housing
Conditional replacement · 046
046: tank-vent retrofit depends on dome shape
TI 11/2000 separates the new tank housing/vent from retrofit kit 1122 350 5851 for the previous housing.
1 46 173 746 — Introduction of the modified tank housing on 046 only.
- New 046 tank housing 1128 350 0822 replaces 1128 350 0812; it uses filter 1122 358 1800 and vent 1128 350 5802.
- For the previous housing, use retrofit kit 1122 350 5851 after removing cap 1121 358 2500 and filter 1121 358 1800; the kit is not the same part as the new-housing vent.
- Slotted dome: hose with internal spring and high thrust ring. Unslotted dome: hose without internal spring and low thrust ring. Inspect the actual housing; do not choose by model name alone.
- The summary confirms introduction from 1 46 173 746 on the 046; the preceding housing range ends at 1 46 173 745. Check the installed housing when selecting retrofit parts.
- The new-housing vent 1128 350 5802 consists of cap (2), hose (3) and vent insert (4) in drawing 145TI037 KN; these are not separately available. Filter 1122 358 1800 is a separate summary row, not one of those three inseparable vent pieces.
- Retrofit kit 1122 350 5851 instead has connector (3), secured to the housing with thrust ring (4), and hose (5) containing a vent insert, as shown in 145TI026 KN. Its component parts are not available separately in this TI. Do not confuse these drawing numbers with the different new-housing vent drawing.
- After removing the old cap and filter and selecting the dome-specific hose/ring, place the tank vent in position. Hold it with suitable pliers and press it into the dome by carefully tapping the pliers once or twice with a mallet (145TI030/031 KN). Then fit the proper thrust ring (145TI032 KN).
- Position suitable pliers on top of the thrust ring and press the ring onto the dome by carefully tapping the pliers once or twice (145TI033 KN). Finally position the hose correctly as illustrated in 145TI034 KN. The original page 3 drawing supplies its routing; no numerical insertion depth, impact force or pressure-test specification is given.
- Summary items 1 and 2 describe the respective tank housings as including items 3–5. Item 3 has previous cap 1121 358 2500 and a dash in New; item 4 changes the filter; item 5 introduces vent 1128 350 5802 with no Previous number. Preserve that historical column context: the old cap is not an additional component to fit with the new complete vent. Item 6 introduces the separate retrofit kit, not a replacement for item 5.
- Summary remark 1: previous tank housings are no longer factory-supplied. Remark 2: the previous cap and filter remain available for older machines. Remark 3: kit 1122 350 5851 is for upgrading the previous housing. These are historical supply statements, not present stock or unrestricted interchange.
- Page 1 states the housing change from 1 46 173 746 and older housing through 1 46 173 745 without a model qualifier; page 3 explicitly assigns the introduction to 046 and says 044 is in progress. Preserve both statements and the narrower model-specific summary; no numeric 044 production boundary is established.
- These instructions cover the 044/046 dome-dependent retrofit in this TI. They do not recover the separate kit instruction sheet referenced by TI52/1999 or establish a high/low ring part-number assignment; the latter TI’s named source gap remains separate.
Source: TI 11/2000, p. 1 · TI 11/2000, p. 2 · TI 11/2000, p. 3 — Sections 1–1.3: tank vent, dome assignment and model-specific summary; complete installation/identification drawings and supply remarks reviewed.
Part numbers (7)
- 1128 350 0812 — Tank housingOriginal equipment · 046 previous housing
- 1128 350 0822 — Tank housingNew version · 046 modified vent mounting
- 1121 358 2500 — Vent capOriginal equipment removed for retrofit · 046 previous housing
- 1121 358 1800 — Vent filterOriginal equipment removed for retrofit · 046 previous housing
- 1122 358 1800 — Vent filterNew-housing component · 046 modified housing
- 1128 350 5802 — Tank ventNew-housing component · 046 modified housing, not retrofit kit
- 1122 350 5851 — Tank vent retrofit kitConditional retrofit · 046 previous housing; dome-dependent hose and thrust ring
Conditional replacement · 046
046: AV stop openings are a separate change
TI 03/1999 separates the AV stop changes from the earlier 046 deep-thread crankcase introduction.
1 41 628 724 — 046 AV change, distinct from crankcase screw-depth and bearing changes.
- AV changes from 1 41 628 724 add crankcase stop buffer 1125 791 2810 and tank plug 1110 145 9001 in the provided openings. Insert the crankcase stop from the tank-housing side.
- Tank housing 1128 350 0809 → 1128 350 0812 is assigned to this AV cutoff.
- Crankcase 1128 020 2118 was already introduced for deeper cylinder screw holes at a different earlier cutoff. Its number alone must not be used as proof of the later AV opening.
- The summary lists tank housing item 10 including plug item 4. Remark 1 says original tank housing 1128 350 0809 was no longer available from the factory at the bulletin date; this is not a current stock claim.
- The summary describes replacement crankcase item 5 as including stop buffer item 2 and both bearings (items 8 and 9), although its introduction row uses the earlier 1 41 354 621 cutoff. This replacement-supply description does not prove that every production crankcase at that earlier serial had the later AV opening or optimized bearings.
- The AV introduction also says annular buffers were modified without identifying a separate numbered or dimensional annular-buffer revision.
Source: TI 3/1999, p. 1 · TI 3/1999, p. 2 · TI 3/1999, p. 3 — Sections 1–3: separate AV and case introductions.
Part numbers (5)
- 1128 350 0809 — Tank housingOriginal version · 046
- 1128 350 0812 — Tank housingModified AV version · 046 with plug opening
- 1125 791 2810 — Stop bufferAV component · 046 crankcase with provided opening
- 1110 145 9001 — Plug / stop bufferAV component · 046 modified tank housing
- 1128 020 2118 — CrankcaseNumber shared across staged changes · 046; inspect AV opening and screw-depth revision
Conditional replacement · 046 / MS 460
046 repair / MS 460 transition: tank housing and matching cap
The revised tank housing uses a different filler opening; TI 05/2001 allows the housing-and-cap combination for 046 repairs.
- Tank housing 1128 350 0822 → 1128 350 0833. The new housing is matched to cap 0000 350 0525 and includes the new vent configuration.
- This is not a cap-only retrofit: the filler opening is modified. Do not fit the new cap alone to the old tank opening.
- The source says the new cap would be supplied with replacement tanks for about three years, enabling 046 repairs. That historical packaging period is not a current kit-content guarantee.
- Old cap 0000 350 0520 remains available for older machines in the source. Introduction is in progress; no serial cutoff is stated.
- Retained edition is english / USA. This record does not prove every regional or equipment variant.
- Section 1 renames 046 as STIHL MS 460 within the new naming structure (TI25/2000); the new nameplate stays on the shroud. This naming history is not a universal parts-interchange approval or a serial-identification range.
- The tool-free cap has a grip for operation and is the same type for fuel and oil. To open, raise the grip upright, turn about one-quarter turn counterclockwise, and remove. To close, fit with grip upright and the cap/opening marks aligned, turn about one-quarter turn clockwise to the stop, then fold the grip down. The closing check is that the grip’s lug engages the recess; merely folding the grip down is not the stated check. Drawings 176TI001–004 KN show this sequence for the matching opening.
- Summary item 1 includes items 2–5: filler cap and vent with its valve/filter contents. The nested contents are not additional separately orderable new vent internals. Remark 1 marks the previous housing no longer available from the factory at the time of this TI; remark 2 preserves the previous cap for older machines. Neither is a current stock statement.
Source: TI 5/2001, p. 1 · TI 5/2001, p. 2 · TI 5/2001, p. 3 · TI 5/2001, p. 4 — Complete sections 1–7: 046/MS460 naming, cap operation, tank and crankcase matching assemblies, vent construction/function, clutch and all summary rows.
Part numbers (5)
- 1128 350 0822 — Tank housingPrevious version · 046 previous tank configuration
- 1128 350 0833 — Tank housingNew matching assembly · MS 460 transition; 046 repair with matching cap
- 0000 350 0520 — Filler capPrevious configuration · Older tank opening
- 0000 350 0525 — Filler capRequired matching cap · New tank opening only
- 0000 350 5800 — Tank ventNew tank configuration · MS 460 revised tank assembly
Service note · 046
046: tank-vent directions and conflicting item labels
Air enters near 0.05 bar vacuum and leaves near 0.1 bar pressure; the prose and drawing disagree on the valve item number.
Later reviewed guidance: 046: revised tank housing and inward-only valve
- The source gives approximate vacuum magnitude 0.05 bar (0.725 psi) for inward air flow and pressure 0.1 bar (1.45 psi) for outward flow. These are descriptive operating values, not a complete leak-test procedure or absolute-pressure specification.
- The cap shields the sintered filter from surface icing and permits air circulation in a low-dust region of the carburetor box; the filter limits valve contamination.
- The drawing labels cap 3, sintered filter 2 and valve 1. The prose instead calls both filter and valve item 2. This original item-number conflict is retained; no part number or silent correction is inferred.
Source: TI 46/1995, p. 5 — 1.7: complete tank-vent explanation and diagrams.
No additional parts-table entry added.
Service note · 046
046: historical carburetor and ignition specifications
The original fuel and ignition settings are release-specific reference data, not universal replacement-carburetor settings.
- The original all-position diaphragm carburetor has an integral fuel pump; standard H and L settings are each one turn open. No carburetor type or limiter configuration is specified, so these settings are not assigned to every carburetor listed on the linked later IPL sheets.
- Fuel capacity is 0.94 l (2 US pt). The 1995 source specifies minimum pump octane 89 unleaded, 50: 1 with STIHL 50: 1 two-stroke oil, and 25: 1 with other brand-name air-cooled two-stroke oils. This is historical formulation-dependent guidance, not a new recommendation for current oils.
- Breakerless electronic magneto ignition: module/flywheel air gap 0.15–0.30 mm (0.006–0.012 in), timing 2.0–3.0 mm (0.080–0.12 in) before top dead center.
- Suppressed Bosch WSR 6 F spark plug: 0.5 mm (0.020 in) electrode gap, M14 × 1.25 thread, 9.5 mm (0.37 in) thread length and printed heat range 200. No alternative plug or STIHL part number is inferred.
Source: TI 46/1995, p. 6 · TI 46/1995, p. 7 — 2.2–2.3: fuel, ignition and spark-plug specification.
No additional parts-table entry added.
Service note · 046
046: handle, buffer and cutting-attachment fastener torques
Handle, AV-buffer, bumper and chain-catcher rows keep distinct torques even when thread sizes match.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Switch housing B2.9×9.5: 1 Nm (0.75 lbf.ft); handle molding B3.9×19: 1.6 Nm (1.2 lbf.ft). Buffer/crankcase IS-M4×16: 5 Nm (3.7 lbf.ft), Loctite 242.
- Spiked bumper top with nut IS-M5×12: 7.5 Nm (5.5 lbf.ft); bottom bumper/chain catcher IS-M5×16: 7.5 Nm (5.5 lbf.ft).
- Wrap-around handle with bracket IS-M5×20: 7 Nm (5.2 lbf.ft); left hand guard IS-M5×30: 7 Nm (5.2 lbf.ft).
- Front handle top/bottom IS-P6×19: 8 Nm (5.9 lbf.ft), Loctite 649. Front and rear buffer/tank-housing IS-P6×19: 5.5 Nm (4 lbf.ft); rear-left buffer/tank-housing IS-P6×32.5: 5.5 Nm (4 lbf.ft). Reuse the existing Plastoform thread as page 12 directs.
- Self-locking M5 nut for spiked bumper: 7.5 Nm (5.5 lbf.ft); self-locking M5 nut for chain catcher/spiked bumper: 6 Nm (4.4 lbf.ft). These are separate rows, not interchangeable tightening values.
- The guide-bar collar-nut row prints M8×21.5,23 Nm (17 lbf.ft), remark 2/Loctite 242. That unusual adhesive assignment is retained as printed, not generalized to all bar nuts or silently removed; verify the exact repair context before applying it.
Source: TI 46/1995, p. 11 · TI 46/1995, p. 12 — 5.3: handles, buffers, bumper, guard and guide-bar rows.
No additional parts-table entry added.
Service note · 046
046 C: catalyst fuel and speed limits
Accurate tachometer required; full-throttle limits are 13,000–13,500 rpm.
- For the 046 C catalytic-converter version, corrections to high-speed screw H are permitted only with an accurate tachometer to check that maximum permissible engine speed 13,500 rpm is not exceeded, with a properly tensioned chain. Minimum full-throttle speed must not be below 13,000 rpm. These are not idle-speed specifications or verified measurements.
- The printed fuel requirement is unleaded brand-name gasoline mixed with STIHL 50:1 high-performance two-stroke engine oil or STIHL HT plus 50:1 synthetic engine oil. This records the 1997 catalyst-version instruction, not a new fuel recommendation for every 046 or successor.
- The source also refers to TI11/1993 section1.5, absent from the retained corpus. The locally printed requirement is retained without inventing that missing section. Linked carburetor sheets are navigation aids, not proof that every carburetor variant fits 046 C.
Source: TI 5/1997, p. 2 — Complete sections1.2–1.3.
No additional parts-table entry added.
Historical fitment · 046
046: revised tank housing and inward-only valve
Valve 1110 353 1600 requires the modified housing; tank pressure may remain after stopping.
- Tank housing 1128 350 0806 is modified to accommodate new valve 1110 353 1600 and becomes 1128 350 0809. The summary includes the valve with the housing and identifies original valve 1128 353 1600. It does not authorize fitting the new valve alone into an unmodified housing.
- The upper diagram compares original housing on the left with the new valve construction on the right; the lower diagram arrows show air entering via 1110 353 1600 as fuel volume decreases. Air cannot flow from inside outwards through the new valve. No opening-pressure value is supplied.
- The source warns that sunlight or other heating can build tank pressure while the engine is stopped. Always open the fuel filler cap slowly so accumulated pressure releases gradually and fuel does not spurt out unexpectedly.
- Modification introduction is in progress; no serial cutoff is printed. The original housing is no longer factory-supplied; the original valve remains a spare for older machines and the new valve is already in inventory. These are 1997 supply remarks, not current stock or unrestricted interchange.
- This is a later, explicitly changed housing/valve construction. It does not erase the earlier TI46/1995 item-label conflict or retroactively remove that earlier vent description’s outward flow. TI25/1996 concerns the preceding valve revision with unchanged housing number; its serial is not this 1997 changeover. Last-TI reference43/1996 and page imprint are reviewed, not additional fitment evidence.
Source: TI 5/1997, p. 4 — Entire section4, both diagrams145TI016/017, all summary rows and supply remarks.
Part numbers (4)
- 1128 350 0806 — Original tank housing including valveOriginal assembly · 046 before this housing change
- 1128 350 0809 — Modified tank housing including valveNew assembly · 046; accommodates 1110 353 1600
- 1128 353 1600 — Original tank valveRetained spare · older machines; not blanket interchange
- 1110 353 1600 — New inward-only tank valveNew version · 046 modified housing 1128 350 0809
Conditional replacement · 044 / 046
044 / 046: extra thrust ring in the revised tank-vent package
The added 1128 353 0200 ring is required only on 044 and 046, not on 064/066.
Later reviewed guidance: 044: tank-vent retrofit depends on dome shape · 046: tank-vent retrofit depends on dome shape
- Section 2 replaces complete tank vent 1122 350 5850 with 1122 350 5851 in connection with 044/046 changes. The summary says introduction is in progress, with no numeric serial. The previous complete vent is no longer available from the factory (remark 1); this is a 1999 supply statement.
- The new complete vent includes items 2–4: tank vent 1122 350 5802 and thrust ring 1122 353 0200 retain their numbers, while thrust ring 1128 353 0200 is added. Remark 2 requires the added 1128 ring only for 044 and 046; inclusion in the package is not a requirement to install it on 064/066.
- A detailed instruction sheet is supplied with the vent. It is not reproduced here and was not identified in the bounded 43-file retained docs inventory. Its full installation procedure remains a named source gap; do not infer it from this parts table. TI36/1997 is retained and pending separate review, not missing or automatically reviewed by this citation.
- This 1999 TI gives no high/low ring dimensions, slotted/unslotted dome assignment or hose-spring procedure. Later TI11/2000 provides separate dome-dependent retrofit guidance for 044/046; follow those source-linked conditions without pretending this missing kit instruction sheet has been recovered.
- Historical TI52/1999 instructions and spare-availability statements are not present stock or physical interchange verification. Base-model catalog sheets are navigation anchors; printed R/M variant restrictions remain controlling. No applicability to MS 640, MS 650 or MS 660 is inferred.
Source: TI 52/1999, p. 2 — Section 2, package contents and explicit 044/046-only ring remark.
Part numbers (5)
- 1122 350 5850 — Complete tank vent, previousReplaced; no longer factory-supplied in this TI · 044 / 046 retrofit package only; not universal current-housing fitment
- 1122 350 5851 — Complete tank vent, newIncludes items 2–4; installation is model-specific · 044 / 046 retrofit package only; not universal current-housing fitment
- 1122 350 5802 — Tank vent componentUnchanged item 2 · 044 / 046 retrofit package only; not universal current-housing fitment
- 1122 353 0200 — Thrust ringUnchanged item 3 · 044 / 046 retrofit package only; not universal current-housing fitment
- 1128 353 0200 — Additional thrust ringNew item 4; required only for 044/046 · 044 / 046 retrofit package only; not universal current-housing fitment
Wrong number or missing part for the 046? Report a correction →