← 044/046 · MS 440/460/461

Stihl 1128 · Section P · 15 of 16 · 11 parts

Tools, Extras

Fits 046.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
123440415678
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (11)

PosPart numberDescriptionQty
1 1129 890 3401 Combination wrench 1
2 0812 370 1000 Screwdriver T27x120x70 1
3 0000 890 2300 NLA Screwdriver 1
4 0000 891 0801 NLA Tool roll 1
5 0000 792 9129 Chain scabbard 1
6 0000 792 9132 Chain scabbard extension up to 63 cm Fitment / change note → option 1
7 1110 893 4000 Filing gauge option 1
8 0000 890 2305 Screwdriver 1
40 0781 867 7540 HD filter oil 100 ml 1
41 0781 867 8540 HD filter oil 300 ml 1
Not numbered on the diagram — assemblies, kits and options
— 1121 890 1400 Tool kit 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 046

046: sprocket options and market-dependent standard equipment

Seven- and eight-tooth 3/8-inch sprockets are separate options; only the starred seven-tooth entries may be standard in some markets.

  • The bulletin says 046 can use the same cutting attachments as 044. It does not list every bar length, gauge or drive-link count, and does not waive matching the complete bar/chain/sprocket configuration.
  • The asterisks apply only to the seven-tooth rim kit and seven-tooth spur sprocket: these may be standard equipment in some markets. Neither eight-tooth entry carries that remark.
  • The repair-kit contents are not listed. No equivalence is inferred between the repair kit, sprocket kits and complete clutch assemblies.

Source: TI 46/1995, p. 5 · TI 46/1995, p. 7 — 1.10 and3: cutting attachment and user accessory roster.

Part numbers (6)
  • 1128 900 5001 — 046 repair kitListed user accessory · 046; contents unspecified
  • 1128 007 1000 — 3/8-inch seven-tooth rim sprocket kitStarred option · May be standard in some markets
  • 1128 007 1001 — 3/8-inch eight-tooth rim sprocket kitUnstarred option · 046
  • 1128 640 2000 — 3/8-inch seven-tooth spur sprocketStarred option · May be standard in some markets
  • 1128 640 2005 — 3/8-inch eight-tooth spur sprocketUnstarred option · 046
  • 0000 792 9132 — Chain scabbard extensionListed user accessory · 046

Historical fitment · 046

046: leakage-test and piston tool applications

The service roster distinguishes exhaust sealing, test flange, crankcase vacuum equipment and piston assembly tools.

  • Tool applications are a roster, not a test sequence. The decompression valve must be closed for locking-strip use and replaced by the specified plug for leakage testing. The unlabeled test-object headings on page 10 remain unresolved.
  • The vacuum pump is listed for crankcase leakage; the combined tester is listed for carburetor and crankcase leakage. That tool distinction does not recover the missing page 10 test-object labels.
  • The sleeves appear under the test flange; nipple and fuel line appear under the vacuum pump. No quantity or universal hose substitution is inferred. Installing tool 12 is specifically for hookless piston snap rings.

Source: TI 46/1995, p. 7 · TI 46/1995, p. 8 · TI 46/1995, p. 9 · TI 46/1995, p. 10 — 4.1 and5.1: leakage and piston tools with prerequisites.

Part numbers (13)
  • 0000 893 5903 — Locking strip; crankshaft blocking with valve closedListed tool application · 046
  • 0000 855 8106 — Exhaust sealing plateListed tool application · 046
  • 1108 893 4800 — Wooden piston assembly blockListed tool application · 046
  • 0000 893 2600 — Piston-ring clamping strapListed tool application · 046
  • 1128 850 4200 — Leak-test flangeListed tool application · 046
  • 0000 963 1008 — Test-flange sleevesListed tool application · 046
  • 1106 850 2905 — Carburetor and crankcase testerListed tool application · 046
  • 0000 850 3501 — Crankcase vacuum pumpListed tool application · 046
  • 0000 855 9200 — Vacuum-pump nippleListed tool application · 046
  • 1110 141 8600 — Vacuum-pump fuel lineListed tool application · 046
  • 1122 025 2200 — Plug in place of decompression valveListed tool application · 046
  • 1111 893 4700 — Piston-pin assembly driftListed tool application · 046
  • 5910 890 2212 — Installing tool 12 for hookless snap ringsListed tool application · 046

Historical fitment · 046

046: keep starter-side and clutch-side tools distinct

Oil-seal sleeves, bearing arbors and crankshaft tools have explicit side-specific applications.

  • Starter-side seal protection uses guide 1123 894 7700. The two oil-seal press sleeves and two bearing press arbors are not interchangeable merely because each pair has similar names.
  • AS 5910 007 2205 removes the crankshaft at the clutch side; its sleeve 5910 893 2420 installs the crankshaft. ZS 5910 007 2220 removes the crankshaft at the starter side; sleeve 5910 893 2409 draws the crankcase halves together.
  • The source prints AS 5910 007 2205. The existing later-source 890/0072205 conflict remains unresolved; this roster does not establish an alias or approve a substitute tool.

Source: TI 46/1995, p. 8 — 4.1: seals, bearings and crankshaft tools.

Part numbers (13)
  • 0000 890 4400 — Oil-seal pullerListed side/application · 046
  • 0000 893 3706 — Puller jaws No.3.1Listed side/application · 046
  • 0000 893 3700 — Puller jaws No.1Listed side/application · 046
  • 1115 893 4600 — Oil-seal sleeve, starter sideListed side/application · 046
  • 1118 893 4602 — Oil-seal sleeve, clutch sideListed side/application · 046
  • 1123 894 7700 — Seal-protection guide, starter sideListed side/application · 046
  • 5910 007 2205 — AS crankshaft tool, clutch sideListed side/application · 046
  • 5910 893 2420 — AS screw sleeve, crankshaft installationListed side/application · 046
  • 5910 007 2220 — ZS crankshaft tool, starter sideListed side/application · 046
  • 5910 893 2409 — Screw sleeve, crankcase joiningListed side/application · 046
  • 1118 893 7200 — Bearing press arbor, clutch sideListed side/application · 046
  • 1120 893 7200 — Bearing press arbor, starter sideListed side/application · 046
  • 0811 611 8380 — A19 DIN5254 pliers, crankshaft retaining ringListed side/application · 046

Historical fitment · 046

046: Plastoform refitting and workshop-tool limits

Re-engage the existing polymer thread and tighten with a torque wrench; the T-handle is release-only on Plastoform screws.

  • For refitting a Plastoform screw, rotate counterclockwise until it drops into the existing thread, then tighten clockwise to the specified torque. This avoids forming a second thread; no new-hole torque is supplied here.
  • The QI-T27x 150 T-handle is for releasing only on Plastoform screws. The roster calls for a torque wrench when tightening them. Optical/acoustic signalling is specifically noted for wrench 0302 and 0312.
  • The lower wrench range is printed as 0.5–18 Nm (0.325–13.5 lbf.ft), the higher as 6–80 Nm (4.5–60 lbf.ft). Preserve printed units/rounding; these ranges are not component torque values.
  • Hot air is described as an aid to releasing adhesive-secured screws, with explicit care around polymer components. No temperature or heating duration is specified.
  • The assembly tube 1117 890 0900 appears twice, once for brake springs and once for clutch springs. The stand/clamping-bar pairing is historical 046 guidance, not resolution of the later support-kit screw conflict.

Source: TI 46/1995, p. 8 · TI 46/1995, p. 12 — 4.1 remarks and5.3 continuation: general tools and existing threads.

Part numbers (17)
  • 1117 890 0900 — Assembly tube, brake and clutch springsListed tool application · 046
  • 5910 893 0501 — M8 bar-stud pullerListed tool application · 046
  • 1111 890 6400 — Ignition air-gap gaugeListed tool application · 046
  • 1116 893 4800 — Rewind-spring assembly toolListed tool application · 046
  • 5910 893 8800 — Fuel-pickup assembly hookListed tool application · 046
  • 5910 890 3100 — Assembly standListed tool application · 046
  • 5910 890 2005 — Clamping bar for mounting sawListed tool application · 046
  • 5910 890 0301 — Torque wrench, lower rangeListed tool application · 046
  • 5910 890 0302 — Torque wrench, lower range with signalListed tool application · 046
  • 5910 890 0311 — Torque wrench, higher rangeListed tool application · 046
  • 5910 890 0312 — Torque wrench, higher range with signalListed tool application · 046
  • 5910 890 2400 — QI-T27x 150 T-handleListed tool application · 046
  • 5910 890 8210 — Electrical connector crimping toolListed tool application · 046
  • 1110 893 4500 — Flywheel pullerListed tool application · 046
  • 5910 893 5608 — 13 mm flywheel-nut socketListed tool application · 046
  • 5910 893 5613 — 19 mm clutch socketListed tool application · 046
  • 0812 542 2104 — T27x 125 IS screwdriverListed tool application · 046

Historical fitment · 046

046: original servicing aids and adhesive distinctions

Lubricants have separate stated applications; Loctite 242,270 and 649 are not presented as interchangeable.

  • Lubricating grease 0781 120 1111 is listed for oil seals, oil-pump drive and sprocket bearing. The same application column also prints “Cleaning crankshaft stub” without a separately named cleaner. Preserve that anomalous row; do not infer grease is a cleaning solvent.
  • Special lubricant 0781 417 1315 is for the rope-rotor bearing bore and starter-cover rewind spring. Multipurpose grease 0781 120 1109 is for the ignition module high-voltage output.
  • The electrician’s repair kit has no contents/application detail on this page. Gasket panel 0457 281 1704 is labeled 044/046, not a claim that their cylinder gaskets interchange.
  • The source lists medium-strength Loctite 242 and high-strength 270/649. Component-specific page 11 remarks determine which is called for; later formulation equivalents are not established.

Source: TI 46/1995, p. 9 · TI 46/1995, p. 11 — 4.2 and5.3 remarks: servicing aids and adhesive assignments.

Part numbers (5)
  • 0781 120 1111 — Lubricating greaseHistorical servicing aid · 046 roster; no current substitute inferred
  • 0781 417 1315 — STIHL special lubricantHistorical servicing aid · 046 roster; no current substitute inferred
  • 0000 007 1013 — Electrician’s repair kitHistorical servicing aid · 046 roster; no current substitute inferred
  • 0781 120 1109 — STIHL multipurpose greaseHistorical servicing aid · 046 roster; no current substitute inferred
  • 0457 281 1704 — Gasket panel 044/046Historical servicing aid · 046 roster; no current substitute inferred

Service note · 046

046: handle, buffer and cutting-attachment fastener torques

Handle, AV-buffer, bumper and chain-catcher rows keep distinct torques even when thread sizes match.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Switch housing B2.9×9.5: 1 Nm (0.75 lbf.ft); handle molding B3.9×19: 1.6 Nm (1.2 lbf.ft). Buffer/crankcase IS-M4×16: 5 Nm (3.7 lbf.ft), Loctite 242.
  • Spiked bumper top with nut IS-M5×12: 7.5 Nm (5.5 lbf.ft); bottom bumper/chain catcher IS-M5×16: 7.5 Nm (5.5 lbf.ft).
  • Wrap-around handle with bracket IS-M5×20: 7 Nm (5.2 lbf.ft); left hand guard IS-M5×30: 7 Nm (5.2 lbf.ft).
  • Front handle top/bottom IS-P6×19: 8 Nm (5.9 lbf.ft), Loctite 649. Front and rear buffer/tank-housing IS-P6×19: 5.5 Nm (4 lbf.ft); rear-left buffer/tank-housing IS-P6×32.5: 5.5 Nm (4 lbf.ft). Reuse the existing Plastoform thread as page 12 directs.
  • Self-locking M5 nut for spiked bumper: 7.5 Nm (5.5 lbf.ft); self-locking M5 nut for chain catcher/spiked bumper: 6 Nm (4.4 lbf.ft). These are separate rows, not interchangeable tightening values.
  • The guide-bar collar-nut row prints M8×21.5,23 Nm (17 lbf.ft), remark 2/Loctite 242. That unusual adhesive assignment is retained as printed, not generalized to all bar nuts or silently removed; verify the exact repair context before applying it.

Source: TI 46/1995, p. 11 · TI 46/1995, p. 12 — 5.3: handles, buffers, bumper, guard and guide-bar rows.

No additional parts-table entry added.

Wrong number or missing part for the 046? Report a correction →