← 044/046 · MS 440/460/461

Stihl 1128 · Section O · 14 of 16 · 27 parts

Handlebar, Heating element

Fits 046.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101010111112121313141415151617171718192202021222324252534404040405667789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (27)

PosPart numberDescriptionQty
1 1128 790 1753 Handlebar Fitment / change note → 1
2 1128 790 1754 Handlebar Fitment / change note → 1
3 1128 790 3616 Wrap around handlebar 1
4 1128 790 3619 Wrap around handlebar 1
5 not sold separately Handle hose 450 mm / 17 13/16'' 1
6 not sold separately Insulating hose not available as a separate item 1
7 0000 442 7000 NLA Contact sleeve no longer available from factory 1
8 not sold separately Handle hose 164 mm not available as a separate item 1
9 not sold separately Handle hose 373 mm not available as a separate item 1
10 9074 478 4435 Pan head self-tapping screw IS-P6x19 Fitment / change note → 2
11 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 Fitment / change note → 2
12 1128 791 5501 Elbow connector 1
13 1128 791 5500 Elbow connector → replaced by 1128 791 5501 TI 15/2007 1
14 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
15 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 2
16 1128 434 5000 NLA Heating element 1
17 1118 431 6700 NLA Terminal socket no longer available from factory 2
18 1118 431 6600 NLA Terminal pin no longer available from factory 1
19 1121 791 9000 NLA Clamp 1
20 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' 2
21 1128 430 0200 Switch 1
22 0000 958 1511 Washer 1
23 1128 432 2200 Hexagon nut 1
24 1110 432 9200 Grommet 1
25 9307 021 0120 Washer 5.3 1
40 9074 478 4435 Pan head self-tapping screw IS-P6x19 Fitment / change note → 4
Not numbered on the diagram — assemblies, kits and options
— 0000 791 2009 Handle hose Ø 19 mm x 5 m / 3/4x197'' not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046: stiffened handle needs matching version and screws

TI 11/2000 changes front handles and mounting screw length; heated variants must retain the correct electrical pairing.

  • Stiffened replacement handles require the longer IS-P6×21.5 screws 9074 478 4475 in place of IS-P6×19 screws 9074 478 4435. The TI describes historical supply with handles, not guaranteed current contents.
  • 046 non-heated: front handle 1128 790 1701 → 1128 790 1753.
  • 046 heated: front handle 1128 790 1706 → 1128 790 1754.
  • Do not assign the 044 heated replacement numbers 1751/1752 or their resistance table to the 046; its summary lists 1128 790 1754.
  • The stiffener adds thickness: drawing 145TI038 KN labels A without stiffener and B with stiffener. The longer screws are supplied with replacement handles according to page 4. Summary items 6 and 7 each specify two screws (2x); do not retain the shorter screws for the stiffened arrangement.
  • Each front-handle summary row literally says including items 6, 7, spanning the previous IS-P6 × 19 and new IS-P6 × 21.5 screw rows. Page 4 specifies replacement supply with the longer screws; the summary is not evidence that both lengths must be installed or are both supplied with a current replacement.
  • The modification is in progress, with no numeric stiffened-handle introduction serial. Previous short screw 9074 478 4435 has no new number in its own row and remains available for other, unnamed models (remark 3); the new long screw is separately item 7. This does not retain the short screw for a stiffened handle.
  • Summary remark 1 ends factory supply of previous 046 non-heated 1128 790 1701 and 046 W heated 1128 790 1706. The replacement 046 W handle is 1128 790 1754; its resistance is not specified by the 1751/1752 assignment table. No 044 serial restriction or resistance value is transferred to it.
  • Last-TI references 35/1999 for 044 and 28/1999 for 046 are bibliography, not supersession or authority to mix the two models’ electrical arrangements.

Source: TI 11/2000, p. 4 · TI 11/2000, p. 5 — Sections 2–2.2: front handle assignment and summary; complete installation/identification drawings and supply remarks reviewed.

Part numbers (6)
  • 1128 790 1701 — Front handleOriginal equipment · 046 non-heated
  • 1128 790 1753 — Stiffened front handleConditional replacement · 046 non-heated; longer screws required
  • 1128 790 1706 — Front handleOriginal equipment · 046 heated
  • 1128 790 1754 — Stiffened front handleConditional replacement · 046 heated; longer screws required
  • 9074 478 4435 — IS-P6×19 screwOriginal equipment · 046 original handle
  • 9074 478 4475 — IS-P6×21.5 screwRequired companion · 046 stiffened handle

Service note · 046

046: small-fastener torques, adhesives and ignition washer

The ignition-module screws require both Loctite 242 and a washer; nearby screws have different requirements.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Generator IS-M4×12: 3.5 Nm (2.6 lbf.ft), Loctite 649. Chain-tensioner cover plate IS-M4×8: 3 Nm (2.2 lbf.ft).
  • IS-M4×12 oil-pump cover at sprocket side: 3 Nm (2.2 lbf.ft); brake-band/crankcase: 3 Nm (2.2 lbf.ft), Loctite 242; oil pump: 3.5 Nm (2.6 lbf.ft).
  • IS-M4×12 segment/fan housing: 2.5 Nm (1.8 lbf.ft); sprocket-side crankcase cover: 3 Nm (2.2 lbf.ft).
  • M5 SK6 collar nut for carburetor/filter base/flange: 6 Nm (4.4 lbf.ft), remark 3/Loctite 270. The table calls the fastener a collar nut although its remark generically says screw; neither label is silently changed.
  • Fan housing IS-M5×20: 7 Nm (5.2 lbf.ft). Ignition module/crankcase IS-M5×20: 7 Nm (5.2 lbf.ft), Loctite 242 AND a washer under the screw head. Do not transfer this washer requirement to every M5 screw.

Source: TI 46/1995, p. 11 — 5.3: M4 rows, intake collar nut, fan housing and ignition.

No additional parts-table entry added.

Service note · 046

046: handle, buffer and cutting-attachment fastener torques

Handle, AV-buffer, bumper and chain-catcher rows keep distinct torques even when thread sizes match.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Switch housing B2.9×9.5: 1 Nm (0.75 lbf.ft); handle molding B3.9×19: 1.6 Nm (1.2 lbf.ft). Buffer/crankcase IS-M4×16: 5 Nm (3.7 lbf.ft), Loctite 242.
  • Spiked bumper top with nut IS-M5×12: 7.5 Nm (5.5 lbf.ft); bottom bumper/chain catcher IS-M5×16: 7.5 Nm (5.5 lbf.ft).
  • Wrap-around handle with bracket IS-M5×20: 7 Nm (5.2 lbf.ft); left hand guard IS-M5×30: 7 Nm (5.2 lbf.ft).
  • Front handle top/bottom IS-P6×19: 8 Nm (5.9 lbf.ft), Loctite 649. Front and rear buffer/tank-housing IS-P6×19: 5.5 Nm (4 lbf.ft); rear-left buffer/tank-housing IS-P6×32.5: 5.5 Nm (4 lbf.ft). Reuse the existing Plastoform thread as page 12 directs.
  • Self-locking M5 nut for spiked bumper: 7.5 Nm (5.5 lbf.ft); self-locking M5 nut for chain catcher/spiked bumper: 6 Nm (4.4 lbf.ft). These are separate rows, not interchangeable tightening values.
  • The guide-bar collar-nut row prints M8×21.5,23 Nm (17 lbf.ft), remark 2/Loctite 242. That unusual adhesive assignment is retained as printed, not generalized to all bar nuts or silently removed; verify the exact repair context before applying it.

Source: TI 46/1995, p. 11 · TI 46/1995, p. 12 — 5.3: handles, buffers, bumper, guard and guide-bar rows.

No additional parts-table entry added.

Historical fitment · 046

046: shared ignition module and higher-output generator

TI02/1996 also names 046 for the universal module and higher-output generator, not for the 066 crankshaft or flywheel.

Later reviewed guidance: 046: later ignition guidance replaces the universal-module rule

  • The 066 bulletin explicitly says a universal ignition module and higher-output generator will also be installed in 046. Sections 2.2 and 2.3 identify the new versions as 0000 400 1303 and 1128 404 3501.
  • This shared-component statement does not extend 066 flywheel numbers, crankshaft dimensions, crankcase compatibility, heater retrofit or X 33 917 066 changeover to 046.
  • No 046-specific introduction serial, old module/generator number or all-variant coverage is given here. The 066 old/new flywheel prohibition is not a complete 046 conversion procedure.

Source: TI 2/1996, p. 2 — 2.1–2.3: explicit 046 inclusion for module and generator.

Part numbers (2)
  • 0000 400 1303 — Universal ignition moduleExplicit shared-component statement · 046; variant and serial not supplied here
  • 1128 404 3501 — Higher-output generatorExplicit shared-component statement · 046; variant and serial not supplied here

Wrong number or missing part for the 046? Report a correction →