Stihl 1129 · Section A · 1 of 12 · 37 parts
Crankcase
Fits 020 T, 020.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1129 020 2600 | Crankcase | 1 |
| 2 | 9531 003 0105 | Roller bearing 12x24.5x8.8 | 2 |
| 3 | 9640 003 1191 | Oil seal 12x20x5 | 2 |
| 4 | 0000 988 5211 | Connector | 1 |
| 5 | 1129 792 5500 | Bushing | 1 |
| 6 | 1129 020 2900 | Crankcase Fitment / change note → | 1 |
| 7 | 1128 640 9100 | Valve | 1 |
| 8 | 9416 868 5631 | Hollow rivet 5.5x0.5x6.8 | 2 |
| 9 | 1129 647 9400 | Hose | 1 |
| 10 | 1123 640 3800 | Pickup body | 1 |
| 11 | 0000 350 0510 | Filler cap | 1 |
| 12 | 0000 359 1210 | Sealing ring | 1 |
| 13 | 0000 350 0900 | Rope | 1 |
| 14 | 0000 353 0600 | Hook | 1 |
| 15 | 1129 029 0500 | Gasket | 1 |
| 16 | 1129 030 0400 | Crankshaft | 1 |
| 17 | 1120 036 8500 | Woodruff key 2x3.7 | 1 |
| 18 | 9022 313 0680 | Spline screw IS-M4x16 | 8 |
| 19 | 1129 029 2300 | Cylinder gasket | 1 |
| 20 | 1129 020 1201 | Cylinder with piston Ø 40 mm | 1 |
| 21 | 1129 030 2002 | Piston Ø 40 mm | 1 |
| 22 | 1120 034 1501 | Piston pin 9x5x23 | 1 |
| 23 | 9463 650 0900 | Snap ring 9x0.8 | 2 |
| 24 | 1114 034 3001 | Piston ring Ø 40x1.5 mm | 2 |
| 25 | 9512 003 2030 | Needle cage 9x12x10 | 1 |
| 26 | 9022 341 0980 | Spline screw IS-M5x16 | 4 |
| 27 | 1129 149 0600 | Muffler gasket | 1 |
| 29 | 1129 140 0601 | Muffler | 1 |
| 30 | 1129 140 2000 | Insert | 1 |
| 31 | 9075 478 3015 | Pan head self-tapping screw IS-D4x15 | 1 |
| 32 | 1129 145 1000 | Insert | 1 |
| 33 | 9331 630 0120 | Conical spring washer 5 | 2 |
| 34 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 35 | 1129 664 0500 | Bumper spike | 1 |
| 36 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 37 | 9022 341 0980 | Spline screw IS-M5x16 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1129 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 020 T
020 T: bonded muffler must not be opened
TI 33/1994 explicitly overrides service-manual chapter 4.1 muffler descriptions and illustrations.
- EXHAUST MUFFLER MUST NOT BE OPENED. Upper and lower casings are BONDED together. Mounting screws are secured with adhesive and MUST NOT BE UNDONE; attempting to loosen them can SHEAR THEM OFF. Once opened, muffler cannot be effectively sealed again. No heat, solvent, repair sealant or opening exception is authorized by this source.
- This explicitly corrects the descriptions AND illustrations of service manual chapter 4.1 Muffler. The source supplies no muffler part number, no production serial and no extension to 020 or MS 200 T. Shared020 T/020 catalog sheet is a navigation binding ONLY; model scope stays 020 T. Later catalog rows do not establish a historical part-number or screw-number attribution.
- Footer 20 June 1994; prior TI 25.93 reference is bibliography. This is an accepted manual correction, not whole-manual acceptance or a new manual import.
- Historical TI 33/1994 guidance only. No successor or unlisted model applicability inferred. No physical interchange test was performed. No hardware operation was performed.
Source: TI 33/1994, p. 1 — 020 T: bonded muffler must not be opened.
No additional parts-table entry added.
Service note · 020 T
020 T: remove muffler insert at an angle without removing the muffler
Only the insert’s 4x15 DG screw is removed; do not confuse it with the bonded-casing screws.
- For CLEANING OR REPLACING THE INSERT it is NOT necessary to remove the muffler. Remove the 4x15 DG screw, then pull the insert out AT AN ANGLE. This narrow exception is for insert access, not loosening the adhesive-secured muffler mounting/casing screws or opening the bonded muffler.
- Upper/lower muffler casings are bonded; muffler MUST NOT BE OPENED, adhesive-secured mounting screws MUST NOT BE UNDONE, risk of shearing and inability to reseal. No cleaning chemical, tightening torque, screw part number or alternate insert dimension supplied.
- Exact 020 T scope only, notwithstanding shared 020 T/020 IPL sheet. The later IPL has insert and IS-D4x15 screw rows but the TI itself provides no full part numbers; no fabricated TI number assertion. Chapter 4.1 correction only, not whole-manual acceptance.
- Historical TI 33/1994 guidance only. No successor or unlisted model applicability inferred. No physical interchange test was performed. No hardware operation was performed.
Source: TI 33/1994, p. 1 — 020 T: remove muffler insert at an angle without removing the muffler.
No additional parts-table entry added.
Service note · 020 / 020 T
020/020 T bar mounting: stud to collar screw
Same clutch-side crankcase number; production change in progress.
- Section 1 replaces M8 stud 0000 953 1402 with M8 collar screw 1129 664 2401 to optimize bar mounting. Drawing 142TI003 identifies 1 as ORIGINAL and 2 as NEW; the new screw has a visibly distinct collar. No dimensions or installation torque are given.
- Clutch-side crankcase 1129 020 2900 appears in BOTH original and new columns. Only the MODIFIED crankcase is available from the factory; original stud remains available as a spare. The unchanged crankcase number alone cannot identify which fastener arrangement it contains.
- The summary says including items 1 and 2, but old/new dashes distinguish original stud from new collar screw. This is not proof that both fasteners are supplied together. All other parts as before. Introduction is IN PROGRESS, with no printed machine-number cutoff; do not borrow the section 4 air-filter cutoff.
- The original cover reads Series 1129; retained extracted heading truncates it to Series 112. The original model labels are 020 and 020 T. No source text or primary catalogue metadata was silently corrected.
- Historical 1997-20 evidence for 020, 020 T only; not later MS successors or unlisted variants. Source-era factory supply is not current stock. No reciprocal interchange or physical verification inferred. No hardware operation was performed.
Source: TI 20/1997, p. 1 — 020/020 T bar mounting: stud to collar screw.
Part numbers (3)
- 1129 020 2900 — Clutch-side crankcaseSame number; modified version only · 020, 020 T; 020/020 T bar mounting: stud to collar screw; stated configuration only
- 0000 953 1402 — Original M8 stud, item 1Still supplied as spare · 020, 020 T; 020/020 T bar mounting: stud to collar screw; stated configuration only
- 1129 664 2401 — New M8 collar screw, item 2Production bar-mount change · 020, 020 T; 020/020 T bar mounting: stud to collar screw; stated configuration only
Conditional replacement · 020 T
020 T: two crankcase covers supplied as a complete set
Cover set 1129 020 1150 includes covers 1129 021 1100 and 1129 021 1105; separate supply ends.
- Section 2 says covers 1129 021 1100 and 1129 021 1105 will only be supplied as a complete set to ease replacement. The complete cover is ordered as 1129 020 1150. Summary item 1 includes items 2 and 3; this is a two-cover supply relationship, not two alternate complete-set numbers.
- The new-number column has dashes for individual items 2 and 3, and the previous-number column has a dash for the complete set. Do not read those dashes as additional replacements, zero quantities or new individual-cover numbers. Remark 1 says the previous covers are no longer available as separate items, not that they are absent from the complete set.
- The modification is in progress, without a serial cutoff. The TI gives no fastener/seal contents beyond the two named covers, no fitting procedure and no claim that the cover geometries were changed.
- The retained 01-2012 combined 020 T/020 crankcase sheet A contains none of these three numbers. Its exact-model assembly link provides context only: no drawing positions, later replacements or present-day set contents are invented. Shared sheet applicability does not extend the TI beyond 020 T.
- The retained TI17/1999 USA originals name Model 020 T, series 1129, and contain only tank-housing pickup hose and crankcase-cover sections. The extracted title mentioning a compensator carburetor and the catalog C1Q-S16A sheet labeled (17.1999) do not establish a carburetor change in these retained pages. Do not extend this evidence to rear-handle 020, earlier series 1114, MS 200 T/MS 200 or MC 200. Factory supply statements are historical, not current availability; no physical interchange has been tested.
Source: TI 17/1999, p. 1 · TI 17/1999, p. 2 — Both original USA pages: full sections 1 and 2, figure 142TI013 KN, both summary tables, introduction lines, remarks and bibliography.
Part numbers (3)
- 1129 020 1150 — Complete cover set; summary item 1Includes items 2 and 3 · 020 T; TI17/1999 USA
- 1129 021 1100 — Cover; summary item 2Included in complete set; no separate factory supply · 020 T; TI17/1999 USA
- 1129 021 1105 — Cover; summary item 3Included in complete set; no separate factory supply · 020 T; TI17/1999 USA
Wrong number or missing part for the 020 T, 020? Report a correction →