← 020 T · MS 200 · MS 200 T

Stihl 1129 · Section E · 4 of 12 · 20 parts

Chain sprocket cover

Fits 020 T, 020.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161722021223456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (20)

PosPart numberDescriptionQty
1 1129 640 1702 Chain sprocket cover Fitment / change note → 1
2 1120 162 5200 Pin 1
3 1129 640 5000 Insert 1
4 9378 543 2700 Notched pin 5x30 Fitment / change note → 1
5 1129 656 7701 Chain catcher Fitment / change note → 1
6 1129 162 6600 Limit stop Fitment / change note → 1
7 9104 003 3004 Self-tapping screw P4x14 Fitment / change note → 2
8 1129 792 9100 Hand guard 1
9 0000 967 3724 Instruction label 1
10 1129 792 9101 Hand guard 1
11 1128 160 5000 Lever 1
12 1123 160 5400 Brake band 1
13 1129 162 7800 Flat spring 1
14 0000 997 1018 Tension spring 1
15 1129 648 7700 Cover 1
16 1123 648 6600 Bumper strip 1
17 0000 955 0801 Hexagon nut M8 1
20 0000 961 1408 Ring 1
21 1114 656 7705 Chain catcher Fitment / change note → → replaced by 1129 656 7701 TI 43/1998 1
22 9104 003 3004 Self-tapping screw P4x14 Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 020 T

020 T chain sprocket cover: assembly discontinued, separate cover revised

Assembly 1129 640 1705 is discontinued; separate cover 1129 640 1701 becomes 1129 640 1702.

  • TI 44/1996 explicitly names MODEL 020 T, series 1129 in the original heading (the retained text truncates the series). It does not establish the same change for 020, MS 200T, MS 200 or MC200 merely because catalog sheets share parts.
  • The chain sprocket cover assembly WITH HAND GUARD is discontinued and is to be supplied as separate parts. Item 1 is 1129 640 1705, including item 2; its new-number cell is a dash. This is not a direct assembly supersession to the separate cover.
  • Item 2 changes from 1129 640 1701 to 1129 640 1702, with modified printing. The notice does not describe additional geometry changes or assign a new hand-guard number. All other parts remain as before.
  • Introduction is IN PROGRESS, with no numeric serial boundary. Remark 1: original assembly no longer factory-available; remark 2: original separate cover supplied only while existing stocks last. These are distinct historical supply conditions.
  • This is historical source guidance, not present stock or a verified physical interchange. Later IPL sheets are navigation, not a reconstruction of the 1996 configuration. No hardware operation was performed.

Source: TI 44/1996, p. 1 — 020 T chain sprocket cover: assembly discontinued, separate cover revised.

Part numbers (3)
  • 1129 640 1705 — Chain sprocket cover assembly with hand guardDiscontinued assembly · 020 T; includes separate cover item 2; no new assembly number
  • 1129 640 1701 — Chain sprocket coverOriginal separate cover · 020 T; historical stocks-only supply
  • 1129 640 1702 — Chain sprocket coverNew separate cover · 020 T; modified printing

Historical fitment · 020 T

020 T: modified sprocket cover keeps the same number

Cover 1129 640 1702 changes for chip flow; its number alone does not identify the version.

  • Page 1 says the cover was modified to optimize chip flow. Page 2 item 1 prints 1129 640 1702 in BOTH original and new columns; remark 1 says only the modified version is available from the factory. No new order number or dimensional interchange is invented.
  • The summary describes the cover as including items 2 through5, but the new column has no screw at item 5. Preserve this version-dependent table wording; do not turn the range into a claim that the new cover includes the old screw or that the new chain catcher stays attached to the cover.
  • The cover change is in progress, with no serial cutoff. Serial 1 41 340 992 belongs to the separate flywheel change, not the cover, catcher, stop or pin.
  • Historical TI 43/1998 names Model 020 T, series 1129 only. Its broader extracted title and shared later 020 T/020 catalog sheets do not extend these changes to the older 020/series 1114, 015, MC 200 or MS 200 successors. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 43/1998, p. 1 · TI 43/1998, p. 2 — Full cover introduction; page2 item1, inclusion range, remark1 and in-progress line.

Part numbers (1)
  • 1129 640 1702 — Original and modified chain sprocket cover; item1Unchanged number; modified-only factory supply · 020 T; TI 43/1998 only

Conditional replacement · 020 T

020 T: chain catcher moves to the crankcase bumper

New catcher 1129 656 7701 replaces 1114 656 7705 in the modified design; the old catcher remains a spare.

  • Page 1 and figure 142TI005 KN locate the new chain catcher on the spiked bumper on the crankcase. The drawing shows its mounting screw but supplies no screw number, torque or universal mounting procedure.
  • The prose says the old catcher is deleted and replaced; page 2 item 2 remark 2 expressly retains the original catcher as a spare. Item5 original spline screw IS-PT4x14, 9104 003 3004, also has remark 2 and a dash in the new column. Deleted from the new design does not mean unavailable for repairing the original design.
  • The later 2012 cover sheet lists 9104 003 3004 at positions 7 (quantity 2) and 22 (quantity 1). This does not establish that either is the unnumbered new bumper screw in the TI drawing, or override the 1998 table. No automatic screw equivalence is inferred.
  • This replacement is not established for the older 020 or the 015, even though those machines use the same original catcher number. Use the original 020 T heading to determine scope; a broader catalog title or shared part number is not evidence of compatibility.
  • Historical TI 43/1998 names Model 020 T, series 1129 only. Its broader extracted title and shared later 020 T/020 catalog sheets do not extend these changes to the older 020/series 1114, 015, MC 200 or MS 200 successors. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 43/1998, p. 1 · TI 43/1998, p. 2 — 142TI005 KN and catcher text; page2 items2/5, remark2; bounded derived-link correction.

Part numbers (3)
  • 1114 656 7705 — Original chain catcher; item2Retained historical spare · 020 T; TI 43/1998 only
  • 1129 656 7701 — New chain catcher; item2Crankcase spiked-bumper mounting · 020 T; TI 43/1998 only
  • 9104 003 3004 — Original spline screw IS-PT4x14; item5Retained spare; no new-column number · 020 T; TI 43/1998 only

Conditional replacement · 020 T

020 T: retrofit stop and longer locating pin

Stop 1129 162 6600 may be used in older machines; the longer 5x30 pin replaces 5x24.

  • Stop 1129 162 6600 is installed in the chain sprocket cover to help reduce brake-spring vibration; figure 142TI006 KN shows the insertion location and the pin. Page 2 item 3 has no original part number and remark 3 explicitly permits this new STOP in older machines. Do not spread that remark to the entire cover or flywheel.
  • The original notched pin 5x24,9378 543 2640, is replaced by longer 5x30,9378 543 2700, to simplify cover assembly. Item4 remark 4 limits original-pin factory supply to existing stocks; it is not the indefinite spare statement used for catcher and screw.
  • No separate introduction serial or reverse pin interchange is stated. Neither illustration establishes a pin protrusion dimension or insertion depth.
  • Historical TI 43/1998 names Model 020 T, series 1129 only. Its broader extracted title and shared later 020 T/020 catalog sheets do not extend these changes to the older 020/series 1114, 015, MC 200 or MS 200 successors. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 43/1998, p. 1 · TI 43/1998, p. 2 — Stop/pin paragraphs and142TI006 KN; page2 items3/4 and remarks3/4.

Part numbers (3)
  • 1129 162 6600 — Stop; item3Express older-machine use · 020 T; TI 43/1998 only
  • 9378 543 2640 — Original notched pin5x24; item4Factory stocks only · 020 T; TI 43/1998 only
  • 9378 543 2700 — New notched pin5x30; item4Longer replacement · 020 T; TI 43/1998 only

Service note · 020 T

020 T: clean the cylinder locating bore before fitting the cover

The arrow identifies the locating bore in the cylinder, not a drilling or enlargement instruction.

  • Before fitting the new version of the chain sprocket cover with stop and chain catcher, the service note calls for cleaning the locating bore in the cylinder with a suitable tool. Figure142TI007 KN points to the bore beside the flywheel; it does not point to the flywheel hub.
  • The TI gives no cleaning-tool number, bore diameter, drilling instruction, insertion force or torque. The arrow and the cover orientation are service-location evidence, not permission to enlarge the hole. This is a bounded historical service note, not a complete chain-brake overhaul procedure.
  • Historical TI 43/1998 names Model 020 T, series 1129 only. Its broader extracted title and shared later 020 T/020 catalog sheets do not extend these changes to the older 020/series 1114, 015, MC 200 or MS 200 successors. Availability is historical, not current stock. No hardware operation was performed.

Source: TI 43/1998, p. 1 — Complete service note and locating-bore arrow142TI007 KN.

No additional parts-table entry added.

Wrong number or missing part for the 020 T, 020? Report a correction →