← 020 T · MS 200 · MS 200 T

Stihl 1129 · Section D · 3 of 12 · 17 parts

Tank housing 020

Fits 020.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415234566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (17)

PosPart numberDescriptionQty
1 1129 350 0850 Tank housing Fitment / change note → 1
2 1129 351 3000 Reflector foil 1
3 1110 353 1600 Valve 1
4 1129 353 2000 Filter → replaced by 1129 350 5850 TI 49/2002 1
5 1129 351 4000 Insulating plate 1
6 9022 313 0680 Spline screw IS-M4x16 4
7 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
8 0000 359 1220 Sealing ring 1
9 0000 350 0900 Rope 1
10 0000 353 0600 Hook 1
11 1129 352 5500 Clamp 1
12 0000 967 3692 Warning pictogram Filler cap 1
13 1129 358 7701 Hose 1
14 not sold separately Hose 3.1x5.7x102 mm, R3 not available as a separate item 1
15 0000 350 3500 Pickup body 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1
— 1129 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 020

020 winter shutter: use preheating below about 10 °C

Return to summer position above about 10 °C to avoid running problems.

  • Heated cooling air flows over the carburetor and is drawn through the filter as preheated combustion air, helping prevent filter and carburetor icing in cold conditions.
  • The new tank housing and carburetor box (handle frame) provide cutout 1, opened or closed by shutter 2. Figure 144TI003 SC identifies those two features; the numerals are figure labels, not part numbers.
  • Activate intake-air preheating ONLY BELOW APPROXIMATELY 10 °C. Change back to the SUMMER POSITION ABOVE ABOUT 10 °C to avoid engine-running problems. The threshold is approximate; no exact-at-10 rule, automatic thermostat, universal winter kit, shutter-fastener torque or new screw identity is supplied.
  • Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.

Source: TI 10/1997, p. 3 — 020 winter shutter: use preheating below about 10 °C.

No additional parts-table entry added.

Service note · 020

020 handle fasteners: keep 5.3, 5.5 and 2.0 Nm distinct

These three rear-handle values are the exceptions to the 020 T torque baseline.

  • Plastorm screw P 6x32.5, FRONT HANDLE TO HANDLE FRAME: 5.3 Nm. Spline screw, STOP BUFFER TO TANK HOUSING: 5.5 Nm. Collar screw P 5, HANDLE FRAME (REAR HANDLE) TO STOP BUFFER: 2.0 Nm.
  • Only torques differing from 020 T are printed here; the TI calls all others identical. It does not give a full fastener part number, the spline-screw dimensions, an adhesive requirement, or a reused-thread torque reduction for these three exceptions. Do not assign the later IPL number simply by proximity.
  • The available 020 T manual has copyright 1999 and a separate model-specific torque table. In particular its front-handle/handle-housing P6x21.5 row is a DIFFERENT fastener from the TI P6x32.5 row. Do not replace the 020 values with 020 T values or borrow its footnotes without exact joint evidence. All 29 later-table rows and their footnotes are now reviewed separately in the later 020 T notes below; this does not make them rear-handle 020 exceptions.
  • Applies to the rear-handle 020 introduced in TI10/1997, series 1129; not the earlier 020 generation, 020 T or MS 200 by name similarity. No production serial cutoff, universal retrofit, tested interchange or current supply claim. No hardware operation was performed.

Source: TI 10/1997, p. 4 — 020 handle fasteners: keep 5.3, 5.5 and 2.0 Nm distinct.

No additional parts-table entry added.

Service note · 020 / 020 T

020/020 T tank housing: hose ordered separately

0800 to 0850 changes supply contents, not a hose supersession.

  • Tank housing 1129 350 0800 has been replaced by 1129 350 0850. To permit ALL-ROUND USE FOR 020 T AND 020, hose 1129 358 7700 is NO LONGER INCLUDED and must be ORDERED SEPARATELY in future.
  • The table includes item 2 wording must be read with the old hose number and the DASH in its new column: there is no new hose number and no claim that 0850 contains the hose. The original housing is NO LONGER AVAILABLE FROM FACTORY; the hose remains a separate item.
  • Prose says the housing has been replaced, while the summary says introduction IN PROGRESS. Both source statements are retained; neither yields a precise cutoff. Do not apply X 36 503 801 from the filter section to this supply change.
  • Historical 1997-20 evidence for 020, 020 T only; not later MS successors or unlisted variants. Source-era factory supply is not current stock. No reciprocal interchange or physical verification inferred. No hardware operation was performed.

Source: TI 20/1997, p. 2 — 020/020 T tank housing: hose ordered separately.

Part numbers (3)
  • 1129 350 0800 — Original tank housingNo longer supplied by factory · 020, 020 T; 020/020 T tank housing: hose ordered separately; stated configuration only
  • 1129 350 0850 — New common tank housingHose not included · 020, 020 T; 020/020 T tank housing: hose ordered separately; stated configuration only
  • 1129 358 7700 — Hose, item 2Order separately; not superseded · 020, 020 T; 020/020 T tank housing: hose ordered separately; stated configuration only

Wrong number or missing part for the 020? Report a correction →