Stihl 1129 · Section H · 7 of 12 · 29 parts
Air filter 020 T
Fits 020 T.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1129 120 1602 | Air filter | 1 |
| 2 | 1129 120 1607 | Air filter, fleece Fitment / change note → | 1 |
| 3 | 1129 120 3402 | Filter base | 1 |
| 4 | 1129 122 0100 | Foam insert | 1 |
| 5 | 1129 140 1902 | Carburetor box cover | 1 |
| 6 | 1129 148 9200 | Twist lock Fitment / change note → | 1 |
| 7 | 0000 997 0927 | Compression spring | 1 |
| 8 | 9460 624 0500 | E-clip 5 | 1 |
| 9 | 1129 967 1505 | Model plate 020 T, 020 | 1 |
| 10 | 1113 141 1805 | Sleeve | 1 |
| 11 | 1129 141 2200 | Manifold | 1 |
| 12 | 1129 141 3300 | Supporting plate | 1 |
| 13 | 1129 121 8600 | Washer | 1 |
| 14 | 1129 120 0606 | Carburetor WT-326D Fitment / change note → → replaced by 1129 120 0651 TI 37/2000 | 1 |
| 15 | 1129 120 0650 | Carburetor C1Q-S32 | 1 |
| 16 | 1129 122 3300 | Connector | 1 |
| 17 | 9216 261 0700 | Hexagon nut M5 | 2 |
| 18 | 1129 123 7502 | Grommet → replaced by 1129 123 7505 TI 20/2003 | 1 |
| 19 | 1129 790 9900 | Annular buffer | 1 |
| 20 | 9104 003 3004 | Self-tapping screw P4x14 | 2 |
| 21 | 9022 313 0680 | Spline screw IS-M4x16 | 2 |
| 22 | 1116 790 9600 | Annular buffer | 1 |
| 23 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 24 | 1129 791 6100 | Screw | 2 |
| 25 | 1129 790 9902 | Annular buffer | 1 |
| 40 | 1129 967 1500 | Model plate 020 T Fitment / change note → | 1 |
| 41 | 0000 974 1000 | Round head rivet 3x6 Fitment / change note → | 2 |
| 42 | not sold separately | Carburetor C1Q-S16A | 1 |
| 43 | 1129 120 3400 | Filter base Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 020 T
020 T: fleece filter under unchanged numbers
Fleece replaces flocked wire cloth; old stock, cleaning direction and replacement limits remain distinct.
- TI38/1996 replaces flocked wire cloth with fleece under UNCHANGED replacement-part numbers. Introduction is IN PROGRESS, without a serial cutoff. Remark 1 says the unmodified version is supplied until existing stocks are exhausted. A number alone therefore does not identify the material of an old-stock filter; this is a historical supply statement, not a current stock guarantee.
- Page 1 names 020 T, Series 1129, and page 2 prints 1129 120 1606. The later combined 020 T/020 catalog product does not broaden the TI to rear-handle 020 or MS200. Bind only the explicitly titled 020 T filter sheet, not the separate 020 sheet. The TI number is historical evidence even where absent from the later sheet.
- The source calls fleece especially suitable for dry and dusty conditions. Its rougher surface may look heavily contaminated when only lightly loaded; appearance alone does not establish loading. Clean DAILY OR when there is a noticeable loss of power during cutting. The observation about appearance does not cancel that interval.
- If possible, carefully blow out at LOW PRESSURE from the CLEAN AIR SIDE. For stubborn dirt or caked fleece, wash in a clean, NON-FLAMMABLE solution, for example warm soapy water. DO NOT CLEAN WITH A BRUSH: it forces dirt into the fleece. No pressure value, drying time or alternate solvent is specified.
- The source attributes improved filtering efficiency to the material structure, not a measured result here. Some trapped particles cannot be cleaned out; replace the filter when cleaning intervals become too short for practical use, or when noticeable cutting-power loss persists after thorough cleaning.
- Historical guidance for these named models and filter configurations only; no successor-model fitment, universal interchange or material identity inferred from a shared part number. No hardware operation was performed.
Source: TI 38/1996, p. 1 · TI 38/1996, p. 2 — Complete filter-material and servicing guidance; exact model summary rows and remarks.
Part numbers (1)
- 1129 120 1606 — Air filterunchanged material-revision number · 020 T; TI38/1996 row and configuration conditions
Historical fitment · 020 T
020 T carburetor cover: plastic-to-metal twist lock
1113 140 9200 → 1129 148 9200; cover assembly 1129 140 1900 keeps its number.
- The original twist lock 1113 140 9200 is PLASTIC; the replacement 1129 148 9200 is METAL, with a slot for fastening using the screwdriver end of the combination wrench. Drawing 142TI002KN identifies original1 and new2; it is not a separate ordering-number table or a specified tightening torque.
- The section 2 summary keeps carburetor box cover 1129 140 1900 unchanged and includes item 2, the twist lock. Only the modified cover is factory-available in this notice; the original plastic lock remains available FOR OTHER MODELS, which are not named here. Do not turn that statement into fitment for every model using the lock.
- Introduction is IN PROGRESS, no numeric cutoff. Section 3 independently changes the nameplate mounting with the same cover number; the number alone cannot identify either lock material or countersunk-hole generation.
- The exact020T air-filter sheet retains metal lock 1129 148 9200 but lists later cover 1129 140 1902. This is navigation only; TI 44 does not establish a1900-to1902 supersession.
- This is historical source guidance, not present stock or a verified physical interchange. Later IPL sheets are navigation, not a reconstruction of the 1996 configuration. No hardware operation was performed.
Source: TI 44/1996, p. 1 · TI 44/1996, p. 2 — 020 T carburetor cover: plastic-to-metal twist lock.
Part numbers (3)
- 1129 140 1900 — Carburetor box coverUnchanged assembly number · 020 T; includes twist lock; contents modified
- 1113 140 9200 — Plastic twist lockOriginal version · 020 T original; historical supply retained for unspecified other models
- 1129 148 9200 — Metal slotted twist lockNew version · 020 T; fastened with screwdriver end of combination wrench
Historical fitment · 020 T
020 T nameplate: plastic plate requires countersunk cover holes
1129 967 1500 aluminium plate becomes 1129 967 1501 plastic; the plastic plate cannot fit the original cover.
- Riveted ALUMINIUM nameplates are to be replaced in the near future by clip-in PLASTIC nameplates. Two retaining lugs hold the new plate in the carburetor box cover; the two mounting holes are countersunk for this purpose.
- PLASTIC NAMEPLATES CANNOT BE FITTED IN THE ORIGINAL COVER because its holes are not countersunk. Aluminium nameplates and round head rivets remain replacements for older machines. This restriction is not permission to drill or modify an original cover.
- The section 3 summary retains cover 1129 140 1900, including item 2, nameplate. Nameplate 1129 967 1500 becomes 1129 967 1501. Item 3 is TWO round head rivets3x6, 0000 974 1000, with a dash in the new column; not a new rivet number or a quantity-zero instruction for the older assembly.
- Only the modified cover is factory-available in the notice; original nameplate and rivets remain older-machine spares. Introduction is IN PROGRESS, without numeric serials. Unchanged cover number does not prove a loose cover has countersunk holes.
- Later exact020T IPL navigation uses its air-filter/cover sheet and retained rivet number, not a fabricated1900-to1902 replacement claim. Last-TI 33.94 and documentation 5905/copyright 1996 are bibliographic, not additional applicability boundaries.
- This is historical source guidance, not present stock or a verified physical interchange. Later IPL sheets are navigation, not a reconstruction of the 1996 configuration. No hardware operation was performed.
Source: TI 44/1996, p. 2 — 020 T nameplate: plastic plate requires countersunk cover holes.
Part numbers (4)
- 1129 140 1900 — Carburetor box coverUnchanged number with revised holes · 020 T; includes nameplate; inspect original versus countersunk mounting
- 1129 967 1500 — Aluminium nameplateOriginal riveted version · 020 T; retained spare for original cover
- 1129 967 1501 — Plastic nameplateNew clip-in version · 020 T; requires countersunk cover holes; not original cover
- 0000 974 1000 — Round head rivet 3x6Original mounting hardware · Two; retained for older machines with aluminium plate
Service note · 020 T
020 T plastic-fabric filter: before the promised compensator
Plastic filter from X 36 503 801; future fleece combination not yet introduced.
X 36 503 801 — 020 T plastic-fabric filter introduction only; not a compensator or general 020 changeover.
- Section 4 is explicitly 020 T ONLY. To comply with emission regulations, plastic-fabric air filter 1129 120 1605 is to replace fleece filter 1129 120 1606 FROM X 36 503 801. Plastic-fabric 1605 is already in the product line; the text does not name a particular emissions jurisdiction or certify a later retrofit.
- A carburetor WITH COMPENSATOR is announced for these versions IN THE FORESEEABLE FUTURE. The eventual combination is FLEECE CLOTH FILTER AND COMPENSATOR CARBURETOR. This is a future announcement, NOT evidence that the compensator or fleece combination began at X 36 503 801. No carburetor number or later introduction date is supplied.
- Do not extend this 020 T-only cutoff to rear-handle 020 or sections 1–3. The shared catalogue sheet label does not override the explicit section restriction. Last-TI references 020:10.97 and 020 T:44.96 are bibliography, not delegated service instructions. Footer copyright1997/document6035 supplies no exact issue day.
- Historical 1997-20 evidence for 020 T only; not later MS successors or unlisted variants. Source-era factory supply is not current stock. No reciprocal interchange or physical verification inferred. No hardware operation was performed.
Source: TI 20/1997, p. 1 · TI 20/1997, p. 3 — 020 T plastic-fabric filter: before the promised compensator.
Part numbers (2)
- 1129 120 1605 — Plastic-fabric air filter020 T production replacement · 020 T; 020 T plastic-fabric filter: before the promised compensator; stated configuration only
- 1129 120 1606 — Fleece air filterReplaced in stated pre-compensator configuration · 020 T; 020 T plastic-fabric filter: before the promised compensator; stated configuration only
Conditional replacement · 020 T
020 T: fleece filter closes the top-right window
Filter 1129 120 1607 replaces 1129 120 1606 in preparation for future carburetor changes.
- The new fleece air filter closes off the top right-hand window, shown shaded and arrowed in figure 142TI008 KN. This is a revision-identification feature, not an instruction to seal or modify an old filter.
- Summary item1 replaces 1129 120 1606 with 1129 120 1607; remark1 says the original version is no longer available from the factory. Introduction is in progress, with no numeric serial cutoff.
- The changes prepare for future carburetor changes. This bulletin does not identify an installed compensator carburetor, authorize a carburetor swap or establish equivalence with the other filter options on the later combined catalog sheet.
- TI 04/1999 USA names Model 020 T, series 1129. The broader extracted title and shared catalog labels do not extend these assertions to rear-handle 020, earlier series 1114, MC 200 or MS 200 successors. Factory availability is historical, not current stock; physical interchange has not been tested. No hardware operation was performed.
Source: TI 4/1999, p. 1 — Section1 filter paragraph,142TI008 KN,summary item1,remark1 and introduction line.
Part numbers (2)
- 1129 120 1606 — Original fleece air filter; item1Replaced; factory supply ended · 020 T; TI 04/1999 only
- 1129 120 1607 — Modified fleece air filter; item1New version; closed top-right window · 020 T; TI 04/1999 only
Historical fitment · 020 T
020 T: revised filter base keeps number 1129 120 3400
The base is prepared for a future compensator; its unchanged number does not identify its revision.
- The filter base is revised to prepare for future changes (compensator). Figure 142TI000 KN marks the changed upper-right area; no drilling dimension, retrofit machining or complete compensator conversion is specified.
- Summary item2 prints 1129 120 3400 in BOTH previous and new columns. Remark2 says only the modified version is available from the factory. The modification is in progress; no serial cutoff is given, and the number alone does not distinguish the old and modified base.
- The later 2012 catalog sheet also lists base 1129 120 3402. This 1999 bulletin does not replace 1129 120 3400 with that later number or establish interchange between them.
- TI 04/1999 USA names Model 020 T, series 1129. The broader extracted title and shared catalog labels do not extend these assertions to rear-handle 020, earlier series 1114, MC 200 or MS 200 successors. Factory availability is historical, not current stock; physical interchange has not been tested. No hardware operation was performed.
Source: TI 4/1999, p. 1 — Section1 filter-base paragraph,arrow142TI000 KN,summary item2 and remark2.
Part numbers (1)
- 1129 120 3400 — Original and revised filter base; item2Unchanged number; modified-only factory supply · 020 T; TI 04/1999 only
Service note · 020 T
020 T WT 326: trim gasket and metering diaphragm flush
After repairs to carburetor 1129 120 0606, the illustrated protruding edges must be flush with the body.
- After repairs to carburetor 1129 120 0606, always trim away the gasket AND metering diaphragm flush with the carburetor body. Figure 142TI010 KN shows the edge enlarged and a scissor-cut illustration; it does not prescribe a recess, depth or separate component part numbers.
- The TI heading says WT 326 without a suffix; the retained later sheet labels 1129 120 0606 WT-326D. The part-number binding is explicit, but the TI is not evidence that every WT326 suffix is identical. Do not apply the trimming instruction to C1Q-S32, C1Q-S16A, pump diaphragms or all carburetors on the shared air-filter sheet.
- TI 04/1999 USA names Model 020 T, series 1129. The broader extracted title and shared catalog labels do not extend these assertions to rear-handle 020, earlier series 1114, MC 200 or MS 200 successors. Factory availability is historical, not current stock; physical interchange has not been tested. No hardware operation was performed.
Source: TI 4/1999, p. 2 — Complete section3 service note and enlarged scissor detail142TI010 KN.
Part numbers (1)
- 1129 120 0606 — WT 326 carburetor named by service noteRepair-specific gasket/metering-diaphragm trimming · 020 T; TI 04/1999 only
Wrong number or missing part for the 020 T? Report a correction →