Stihl 1130 · Section C · 3 of 10 · 40 parts
Rewind starter, Ignition system
Fits 017.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1130 080 1800 | Fan housing Fitment / change note → | 1 |
| 2 | 1110 084 9102 | Bushing | 1 |
| 3 | 1123 195 0400 | Rope rotor | 1 |
| 4 | 1125 195 7200 | Pawl | 1 |
| 5 | 0000 958 0923 | Washer | 1 |
| 6 | 1118 195 3500 | Spring | 1 |
| 7 | 1129 190 0601 | Rewind spring | 1 |
| 8 | 0000 195 8200 | Starter rope Ø 3x800 mm | 1 |
| 9 | 1121 195 3400 | Starter grip | 1 |
| 10 | 0000 190 3402 | Starter grip ElastoStart Ø 3 mm | 1 |
| 11 | 0000 195 8200 | Starter rope Ø 3x800 mm | 1 |
| 12 | 0000 195 7001 | Cap | 1 |
| 13 | 1130 967 1500 | Model plate 017 Fitment / change note → | 1 |
| 14 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 3 |
| 15 | 9104 003 8733 | Self-tapping screw P4x16 | 1 |
| 16 | 1130 400 1201 | Flywheel | 1 |
| 17 | 1130 400 1200 | Flywheel Fitment / change note → | 1 |
| 18 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 19 | 9075 478 3022 | Pan head self-tapping screw IS-D4x20 | 2 |
| 20 | 1130 400 1302 | Ignition module | 1 |
| 21 | 1128 405 1000 | Spark plug boot | 1 |
| 22 | 0000 998 0604 | Torsion spring | 1 |
| 24 | not sold separately | Terminal socket 4.8-1 not available as a separate item | 1 |
| 25 | 0751 030 8467 | Grommet no longer available from factory | 1 |
| 26 | 0751 030 8490 | Terminal socket 3.5 no longer available from factory | 1 |
| 27 | 1130 440 2201 | Ground wire 125 mm / 4 15/16'' | 1 |
| 28 | 0751 030 8969 | Terminal socket A5-1.5 no longer available from factory | 1 |
| 29 | 0751 030 8953 NLA | Terminal socket 4.8-1 no longer available from factory | 1 |
| 30 | 1130 448 1201 | Lead retainer | 1 |
| 31 | 1130 405 8000 | Insulator | 1 |
| 32 | 1130 400 1300 | Ignition module Fitment / change note → | 1 |
| 33 | 1130 405 1000 | Spark plug boot | 1 |
| 34 | 0000 998 0614 | Torsion spring | 1 |
| 35 | 1130 440 1100 | Short circuit wire 225 mm / 8.9'' | 1 |
| 36 | not sold separately | Terminal socket 6.3-1 not available as a separate item | 1 |
| 37 | 1130 440 2200 | Ground wire 125 mm / 4 15/16'' | 1 |
| 38 | 0751 030 8950 NLA | Terminal socket A 4-1 no longer available from factory | 1 |
| 39 | 1130 448 1200 | Lead retainer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1130 080 2100 | Fan housing with rewind starter Fitment / change note → | 1 |
| — | 1130 080 2105 NLA | Fan housing with rewind starter | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 017
017: series 1130 replacement ignition assignment
1130 400 1300 and the listed flywheel pairing for series 1130; ignition lead not replaceable.
- Listed configuration: 1130 400 1300 with flywheel 1130 400 1200.
- The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.
Part numbers (2)
- 1130 400 1300 — Replacement ignition moduleAssigned replacement · 017, series 1130, only with the listed flywheel branch
- 1130 400 1200 — Listed configuration flywheelRequired pairing · 017, series 1130; listed configuration only
Service note · 017
017 engine, starter and dimensions: original 30.1 cm³ specification
37-mm bore, 28-mm stroke and 3.8-kg dry powerhead; attachment weight excluded.
- Single-cylinder two-stroke engine with special impregnated cylinder bore; displacement 30.1 cm³ (1.84 cu.in), bore 37 mm (1.46 in), stroke 28 mm (1.10 in), compression ratio 9.5:1 and engine power 1.1 kW (1.5 bhp). No bore coating composition is named.
- Maximum torque 1.5 Nm (1.1 lb.ft) at 6500 rpm; mean idle 3200 rpm. These are not maximum unloaded speed or clutch engagement speed.
- One-piece drop-forged crankshaft; TWO deep-groove ball main bearings; crankpin diameter 11.35 mm (0.45 in); cageless cylindrical-roller big end; connecting rod length 51 mm (2 in); piston pin diameter 8 mm (0.3 in); needle-cage small end. No rod-length measurement datum is supplied.
- Lining-free centrifugal clutch diameter 67 mm (2.64 in); engagement approximately 4100 rpm. Pawl starter with automatic rope rewind; rope diameter 3.0 mm (0.12 in), length 800 mm (31.5 in). Later 017 C sheet also lists 3x800-mm rope, but does not make every listed starter/ignition revision original 1995 equipment.
- Dry powerhead WITHOUT BAR AND CHAIN weighs 3.8 kg (8.4 lb). Dimensions WITHOUT BAR AND CHAIN: length 380 mm (14.96 in), width 230 mm (9.0 in), height 250 mm (9.84 in). These are not fueled operating weight or overall cutting-attachment dimensions.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 3 · TI 23/1995, p. 7 · TI 23/1995, p. 8 — Sections 4.1, 4.6 and 4.7.
No additional parts-table entry added.
Service note · 017
017 ignition: air gap, timing and suppressed plugs
0.15–0.30-mm air gap and timing referenced specifically to 8000 rpm.
- Breakerless electronic magneto ignition; module air gap 0.15–0.30 mm (0.006–0.012 in). Ignition timing 1.0–1.6 mm (0.04–0.063 in) BEFORE TOP DEAD CENTER at 8000 rpm; this is piston travel, not crankshaft degrees or a universal static setting.
- Suppressed spark plugs CHAMPION RCJ 6Y or BOSCH WSR 6 F; electrode gap 0.5 mm (0.020 in), thread M14x1.25, thread length 9.5 mm (0.37 in), printed heat range 200. Do not reinterpret 200 as a universal modern cross-brand heat-range equivalence.
- Later 017 B sheet lists Bosch WSR 6 F and NGK BPMR7A. The later NGK listing does not erase the TI Champion option or establish an undocumented 1995 supersession. No plug ordering number is printed in this TI section.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 3 — Section 4.3 ignition system.
No additional parts-table entry added.
Service note · 017
017 fastener torques and DG-thread reuse
The same DG 5x24 thread has different crankcase and fan-housing torques.
- Spline screws: IS-DG 4x20 ignition module/cylinder 5.0 Nm (3.7 lbf.ft); IS-DG 5x24 crankcase 9.5 Nm (7.0); IS-DG 5x24 fan housing/crankcase 4.5 Nm (3.3); IS-DG 5x26 crankcase/cylinder/bar mounting 9.5 Nm (7.0). Same thread size does NOT imply the same component torque.
- M8 collar screw into crankcase 16.0 Nm (11.8 lbf.ft), secured with adhesive 0786 111 1101 (LOCTITE 243), per remark 1. M12x1L clutch collar nut 50.0 Nm (37.0): retain the LEFT-HAND thread suffix L.
- M5 carburetor nut 3.5 Nm (2.6 lbf.ft); M5 muffler/cylinder nut 7.0 Nm (5.2); M8x1 flywheel collar nut 27.5 Nm (20.2); M14x1.25 spark plug 25.0 Nm (18.5). These figures are distinct from valve or bar-fastener values.
- IS-P 4x12 hand guard/fan housing screw 1.7 Nm (1.25 lbf.ft). ONLY THIS ROW carries remark 2: torque may be reduced by approximately 1 Nm (0.7 lbf.ft) when refitting in an existing thread. Do not apply that reduction to every DG screw or all listed fasteners.
- DG screws form a permanent thread in polymer on first installation. To reuse: turn COUNTERCLOCKWISE until the screw drops slightly into the existing thread, then clockwise to specified torque. A torque wrench is essential; cutting a new parallel thread is not the prescribed procedure.
- The TI notes adhesive-secured screws are easier to release after heating adhesive with a hot-air blower/hair dryer; DO NOT OVERHEAT POLYMER COMPONENTS. No heating temperature/time is specified. This is retained historical guidance, not a performed repair.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 7 — Section 4.5, every torque row, DG refitting procedure and remarks.
Part numbers (1)
- 0786 111 1101 — LOCTITE 243 adhesiveremark 1; M8 crankcase collar screw · 017; Section 4.5, every torque row, DG refitting procedure and remarks
Service note · 017
017 piston, ignition, clutch and holding tools
Exact tool applications, including hookless snap rings and 13/19-mm sockets.
- Locking strip 0000 893 5903 blocks crankshaft; clip 1120 893 9100 holds big-end bearing; drift 1114 893 4700 installs piston pin; installing tool 8 5910 890 2208 fits HOOKLESS piston snap rings. The printed 8 is a tool designation, not eight tools.
- Assembly tube 1117 890 0900 fits clutch spring; M8 stud puller 5910 893 0501 unscrews bar-mounting studs. Setting gauge 1111 890 6400 sets ignition module/flywheel air gap. Assembly tool 1116 893 4800 rewinds the rewind spring; hook 5910 893 8800 removes the FUEL pickup body, not the oil pickup.
- Assembly stand 5910 890 3100 holds the saw; clamping bar 5910 890 2000 mounts it to the stand. Crimping tool 5910 890 8210 attaches electrical-wire connectors; puller 1116 893 0800 removes flywheel.
- Socket 5910 893 5608 is 13 mm for the FLYWHEEL NUT; socket 5910 893 5612 is 19 mm for the CLUTCH. No complete interchange or machining specification for these tools is inferred.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 9 — Section 5.2, assembly/holding, electrical, starter and socket rows.
Part numbers (15)
- 0000 893 5903 — Piston locking stripblock crankshaft · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1120 893 9100 — Cliphold big-end bearing · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1114 893 4700 — Assembly driftinstall piston pin · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 2208 — Installing tool 8fit hookless piston snap rings · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1117 890 0900 — Assembly tubefit clutch spring · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 0501 — M8 stud pullerunscrew bar-mounting studs · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1111 890 6400 — Setting gaugeignition module/flywheel air gap · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1116 893 4800 — Assembly toolrewind starter spring · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 8800 — Assembly hookremove fuel pickup body · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 3100 — Assembly standhold saw for repairs · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 2000 — Clamping barmount saw to stand · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 8210 — Crimping toolattach electrical connectors · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1116 893 0800 — Flywheel pullerremove flywheel · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 5608 — 13-mm socketflywheel nut · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 5612 — 19-mm socketclutch · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
Service note · 017
017 servicing aids: grease, low-temperature lubricant and HTR lead
Grease and starter lubricant have different listed applications.
- Lubricating grease 0781 120 1111: oil seals, oil-pump drive, chain-sprocket bearing and switch shaft/contact spring. Low-temperature lubricant 0781 417 1315: REWIND STARTER. Do not silently interchange these application lists.
- Ignition lead HTR, 10 m, is listed as 0000 930 2251 with a BLANK application cell. The 10 m is the listed lead supply length, not a required installed 017 lead length; no cutting length, resistance specification or additional application is supplied.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 10 — Section 5.3, all servicing-aid rows.
Part numbers (3)
- 0781 120 1111 — Lubricating greaseoil seals, pump drive, sprocket bearing, switch shaft/contact spring · 017; Section 5.3, all servicing-aid rows
- 0781 417 1315 — Low-temperature lubricantrewind starter · 017; Section 5.3, all servicing-aid rows
- 0000 930 2251 — Ignition lead HTR, 10 mlisted supply length; application cell blank · 017; Section 5.3, all servicing-aid rows
Service note · 017
017: flywheel keyway revision and reported engine power
Changed keyway moves ignition timing from 22° to 27° before TDC; unchanged flywheel number is not revision identification.
- Section 2 says the flywheel keyway position was changed, moving ignition timing FROM 22 degrees TO 27 degrees BEFORE top dead center. The flywheel part number is UNCHANGED but no numeric flywheel part number is printed here. This describes the factory design change, not an instruction to machine a keyway or alter timing.
- The bulletin attributes mean engine power 1.2 kW (1.6 bhp) to BOTH the timing change and the piston/ring improvement in section 1. It does not establish that either change alone produces this output or give an old power value, measured gain or peak-power specification.
- X 33 249 875 is explicitly attached to the section 1 piston/ring introduction and its summary table. Section 2 prints no separate flywheel introduction serial; do not silently promote that cutoff into a proven flywheel boundary.
- Later sheet C lists flywheels 1130 400 1200 and 1130 400 1201, but TI 28 does not identify which number denotes this unchanged-number revision. Neither catalog number is admitted as the TI flywheel identity. The source also gives no standalone flywheel retrofit instruction.
- Applies to model 017 only; no 018 or MS 170 timing/power inheritance. Historical source description, not a completed hardware adjustment. No hardware operation was performed.
Source: TI 28/1996, p. 1 · TI 28/1996, p. 2 — Complete sections1–2, original comparison drawing, all summary rows and remarks.
No additional parts-table entry added.
Historical fitment · 017
017: model name moves to the fan housing
The redesigned fan housing includes nameplate 1130 967 1500 without changing either housing order number.
- The model designation will no longer appear on top of the shroud. The fan housing was redesigned to accommodate a nameplate; figure 143TI014 KN shows the STIHL 017 plate on its face. Nameplate 1130 967 1500 will be included with the fan housing.
- The second summary repeats fan housing 1130 080 1800 in both version columns and separately repeats fan housing with rewind starter 1130 080 2100. BOTH rows include item 3, nameplate 017, 1130 967 1500. The bare housing and starter assembly are not the same orderable part.
- Second-table remark 1 applies to both housing rows: only the modified version is available from the factory. Do not carry over the first table’s stock-exhaustion remark 1. The new plate has a dash for the original version; the TI does not specify attaching it to an old housing.
- The later 01-2012 exact 017 rewind-starter sheet retains housing 1800 at position 1, assembly 2100 in an unnumbered row and model plate 1500 at position 13. Its additional 2105 assembly is not a replacement established by this TI. The footer reference to TI12/1998 is bibliographic, not an additional fitment dependency or cutoff.
- TI 46/1998 names Model 017, series 1130 only. Shared part numbers in 018 or MS 170/MS 180 catalogs do not extend this historical change to those models. Both modification introductions are in progress, with no serial cutoff. Factory availability statements describe 1998, not current stock; no physical interchange or retrofit procedure is established.
Source: TI 46/1998, p. 1 · TI 46/1998, p. 2 — Complete page2 section2 and143TI014 KN; second summary all three rows, inclusion statements, remark1 and introduction line.
Part numbers (3)
- 1130 080 1800 — Fan housing; second table item1Unchanged number; modified version includes nameplate item3 · 017; TI 46/1998 only
- 1130 080 2100 — Fan housing with rewind starter; second table item2Unchanged number; modified assembly includes nameplate item3 · 017; TI 46/1998 only
- 1130 967 1500 — Nameplate 017; second table item3Newly included with both modified housing versions · 017; TI 46/1998 only
Wrong number or missing part for the 017? Report a correction →