Stihl 1130 · Section D · 4 of 10 · 29 parts
Hand guard, Chain brake
Fits 017.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1130 792 9100 | Hand guard | 1 |
| 2 | 0000 967 3630 | Instruction label | 1 |
| 3 | 1128 160 5000 | Lever | 1 |
| 4 | 0000 958 0521 | Washer | 1 |
| 5 | 1123 162 5800 | Strap | 1 |
| 6 | 9460 624 0400 | E-clip 4 | 1 |
| 7 | 1123 160 5400 | Brake band | 1 |
| 8 | 1123 162 7800 | Flat spring | 1 |
| 9 | 1123 162 7900 | Tension spring → replaced by 1123 162 7902 TI 46/2006 | 1 |
| 10 | 1130 021 1100 | Cover | 1 |
| 11 | 1123 640 7105 | Worm → replaced by 1123 640 7102 TI 5/2005 | 1 |
| 12 | 1123 647 2400 | Spring | 1 |
| 13 | 1123 160 2050 | Clutch | 1 |
| 14 | 1129 162 0800 | Clutch shoe | 3 |
| 15 | 1127 162 3000 | Retainer | 3 |
| 16 | 0000 997 5515 | Tension spring | 3 |
| 17 | 1121 162 1001 | Cover washer | 1 |
| 18 | 1121 162 3000 | Retainer | 3 |
| 19 | 1123 640 2003 | Chain sprocket 3/8" Picco 6T | 1 |
| 20 | 1123 640 2007 NLA | Chain sprocket 1/4" 8T option | 1 |
| 21 | 9512 933 2260 | Needle cage 10x13x10 | 1 |
| 22 | 0000 958 1022 | Washer Ø 27 mm | 1 |
| 23 | 9460 624 0801 | E-clip 8x1.3 | 1 |
| 24 | 1120 664 1500 | Tensioning nut | 1 |
| 25 | 1123 664 1605 | Adjusting screw | 1 |
| 26 | 1123 664 2205 | Cover | 1 |
| 27 | 1123 640 1705 | Chain sprocket cover | 1 |
| 28 | 0000 955 0801 | Hexagon nut M8 | 2 |
| 29 | 1123 656 7700 | Chain catcher option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 017
017 introduction: fixed jet, spark screen and tool-free shroud
Original 1995 equipment includes AV handles and an inertia-tripped chain brake.
- The compact lightweight entry-level saw is described for homeowners/DIY cutting around house and garden. Reliability, ease of use, ergonomics, favorable price and matched cutting attachment are source descriptions, not measured present-day performance.
- Equipment: AV handle system, electronic magneto ignition, inertia-tripped chain brake and exhaust spark-arresting screen. The muffler screen is specified in ALL MARKETS; the exploded figure shows the screen between muffler body and cover, not an optional US-only item.
- The carburetor has a FIXED JET and NO HIGH-SPEED SCREW. The central shroud can be removed WITHOUT TOOLS. The figures give component layout, not an undisclosed part number, carburetor maker/type or conversion procedure.
- The TI attributes meeting US CARB emissions standards to the fixed-jet carburetor and engine tuning. This is a historical source claim, not verification of current emissions compliance or permission to modify emissions equipment.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 1 · TI 23/1995, p. 2 — Sections 1–3, overview and figures 143TI001–003.
No additional parts-table entry added.
Service note · 017
017 fastener torques and DG-thread reuse
The same DG 5x24 thread has different crankcase and fan-housing torques.
- Spline screws: IS-DG 4x20 ignition module/cylinder 5.0 Nm (3.7 lbf.ft); IS-DG 5x24 crankcase 9.5 Nm (7.0); IS-DG 5x24 fan housing/crankcase 4.5 Nm (3.3); IS-DG 5x26 crankcase/cylinder/bar mounting 9.5 Nm (7.0). Same thread size does NOT imply the same component torque.
- M8 collar screw into crankcase 16.0 Nm (11.8 lbf.ft), secured with adhesive 0786 111 1101 (LOCTITE 243), per remark 1. M12x1L clutch collar nut 50.0 Nm (37.0): retain the LEFT-HAND thread suffix L.
- M5 carburetor nut 3.5 Nm (2.6 lbf.ft); M5 muffler/cylinder nut 7.0 Nm (5.2); M8x1 flywheel collar nut 27.5 Nm (20.2); M14x1.25 spark plug 25.0 Nm (18.5). These figures are distinct from valve or bar-fastener values.
- IS-P 4x12 hand guard/fan housing screw 1.7 Nm (1.25 lbf.ft). ONLY THIS ROW carries remark 2: torque may be reduced by approximately 1 Nm (0.7 lbf.ft) when refitting in an existing thread. Do not apply that reduction to every DG screw or all listed fasteners.
- DG screws form a permanent thread in polymer on first installation. To reuse: turn COUNTERCLOCKWISE until the screw drops slightly into the existing thread, then clockwise to specified torque. A torque wrench is essential; cutting a new parallel thread is not the prescribed procedure.
- The TI notes adhesive-secured screws are easier to release after heating adhesive with a hot-air blower/hair dryer; DO NOT OVERHEAT POLYMER COMPONENTS. No heating temperature/time is specified. This is retained historical guidance, not a performed repair.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 7 — Section 4.5, every torque row, DG refitting procedure and remarks.
Part numbers (1)
- 0786 111 1101 — LOCTITE 243 adhesiveremark 1; M8 crankcase collar screw · 017; Section 4.5, every torque row, DG refitting procedure and remarks
Conditional replacement · 017 / 018 / 018 C
018 with PMN: only the revised 3905/3909 guide bars
The optimized-nose Rollomatic Mini bars also fit 017; the old 4105/4109 numbers are not approved here for 018 with PMN.
Model-specific manual evidence: 017/018: later .043 PICCO Mini bar and chain reference · 017/018: later .050 PICCO options and carving-table limits · 017/018 Mini bars: later special-label identities are not supersessions
- The TI says 018 uses the same cutting attachments as 017, but immediately delegates the detailed combinations to the Chains/Bars catalog and adds a specific PMN restriction. The general statement must not override that restriction.
- An optimized nose sprocket changes the Rollomatic Mini guide-bar numbers from 3005 000 4105/4109 to 3005 000 3905/3909. The new versions can also be installed on 017. For PMN (Picco Micro Mini) on 018, ONLY 3005 000 3905/3909 may be installed; their bar label is additionally marked “018”.
- The full four numbers below expand the shared printed prefix; no bar length, gauge, drive-link count, chain part number or unrestricted backward/forward interchange is invented from the TI. The historical former bars are searchable negative/restricted context, not positive 018-PMN fitment. The exact 1998 Chains/Bars catalog was not established in the bounded retained-resource, manual-collection and alternate-database inventory. The linked 2011 references retain later combinations and conflicts separately; they do not replace the missing edition.
- Chain-brake/sprocket-cover sheets are exact-model navigation anchors, not new bar rows or proof that those sheets contain the 1998 cutting attachment. The note does not extend this PMN restriction to every chain type or to successors.
- Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.
Source: TI 42/1998, p. 3 — Complete section2.4,including printed shorthand bar numbers and018-label requirement.
Part numbers (4)
- 3005 000 4105 — Rollomatic Mini guide bar; former numberFormer bar · Former number only; not admitted for 018 with PMN
- 3005 000 4109 — Rollomatic Mini guide bar; former numberFormer bar · Former number only; not admitted for 018 with PMN
- 3005 000 3905 — Rollomatic Mini guide bar; optimized nose sprocketRestricted new bar · 018 with PMN; also installable on 017 per TI
- 3005 000 3909 — Rollomatic Mini guide bar; optimized nose sprocketRestricted new bar · 018 with PMN; also installable on 017 per TI
Service note · 017 / 018
017/018: later .043 PICCO Mini bar and chain reference
The 2011 catalog lists Mini bars and 61 PMMC3 chains; retain its drive-link caveat and the different 1998 bar prefix.
- This is a later USA catalog reference (12th edition, effective January 2011), not the exact catalog cited by TI42/1998. Only the explicitly named 017 and 018 are bound here; the group also contains other models, but no blanket successor or 018 C applicability is inferred. Keep the separate 1998 PMN-only 3905/3909 restriction unchanged.
- The catalog recommends green-labeled reduced-kickback bars together with green-labeled low-kickback chains. Green does not mean kickback-free or tested with every possible powerhead/bar combination. Yellow chains carry increased kickback risk and are intended only for users with extraordinary cutting needs, experience and specialized training. Historical ANSI B175.1-2000 statements are source context, not a new current-compliance certification.
- Bar length is in inches, gauge is the drive-link/bar-groove width in inches, and pitch must match the chain and sprocket. Bar-nose tooth counts are not drive-sprocket tooth counts. The printed 3005 bar-tail template is identification context, not a dimensionally calibrated screen image or proof that every 3005 bar fits. Verify the actual saw, chain, sprocket and bar markings; no physical interchange test or hardware operation was performed.
- PDF28, printed46–47, .043-inch 3/8 P group: 10-inch / 39 drive links — Mini Light 3005 008 7603; 12-inch / 44 links — Mini 3005 000 3905 or Mini Light 3005 000 7605; 14-inch / 50 links* — Mini 3005 008 3909 or Mini Light 3005 000 7609; 16-inch / 55 links* — Mini 3005 008 3913. All listed bar noses have 7 teeth. Blank cells are not additional bar options.
- The bar-table asterisk applies to the 14- and 16-inch rows: add ONE drive link only with BOTH a 7-tooth chain sprocket AND quick chain tensioner (51 and 56 respectively). It is not a universal increase for every 7-tooth sprocket, every bar length or every tensioner.
- PDF17, printed26–27, .043-inch chain group explicitly includes 017/018 and lists green 61 PMMC3 44 (12-inch), 61 PMMC3 50 (14-inch) and 61 PMMC3 55 (16-inch), with a 5/32-inch file. The chain selection page does NOT repeat the bar-table asterisk or list a 39-link 10-inch loop for this group. Preserve that mismatch: do not manufacture 61 PMMC3 51/56 or a 39-link recommendation from the bar table alone. PDF16 identifies PMMC3 .043 PICCO family prefix 3610; this is not a complete order number.
- Across both .043 and .050 3/8 P groups, the sprocket half of the table lists spur 1123 640 2073 with 6 teeth, spur 1123 640 2072 with 7 teeth, rim-sprocket kit 1123 007 1025 with 7 teeth, and replacement rim 0000 642 1240 with 7 teeth. These are grouped alternatives, not claims that a 12-inch bar must use six teeth or a 14-inch bar must use seven, nor proof of individual-saw clutch/kit compatibility.
- The 14-inch Mini bar is printed 3005 008 3909 in the 2011 selection table; TI42/1998 prints 3005 000 3909. This is an unresolved cross-edition prefix difference, not a proved supersession or permission to equate them. The 2011 PMMC3 designation is not silently substituted for the TI’s PMN designation.
TI dependency: TI 42/1998, p. 3 — TI42/1998 section2.4 dependency; later2011 catalog reference, not values printed in the TI.
Later manual evidence: STIHL Bar & Chain Catalog, 12th edition (2011-01), section Selection/warning context printed1–9; chain-family/selection25–27, bar-tail context42–43 and017/018 bar/sprocket groups46–47, PDF pages 3, 4, 5, 6, 7, 16, 17, 26, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · 017 / 018
017/018: later .050 PICCO options and carving-table limits
The 2011 catalog lists green 63 PMC3, 63 PS3 and 63 PD3 separately from yellow 63 PMC; its 1/4-inch model lists differ.
- This is a later USA catalog reference (12th edition, effective January 2011), not the exact catalog cited by TI42/1998. Only the explicitly named 017 and 018 are bound here; the group also contains other models, but no blanket successor or 018 C applicability is inferred. Keep the separate 1998 PMN-only 3905/3909 restriction unchanged.
- The catalog recommends green-labeled reduced-kickback bars together with green-labeled low-kickback chains. Green does not mean kickback-free or tested with every possible powerhead/bar combination. Yellow chains carry increased kickback risk and are intended only for users with extraordinary cutting needs, experience and specialized training. Historical ANSI B175.1-2000 statements are source context, not a new current-compliance certification.
- Bar length is in inches, gauge is the drive-link/bar-groove width in inches, and pitch must match the chain and sprocket. Bar-nose tooth counts are not drive-sprocket tooth counts. The printed 3005 bar-tail template is identification context, not a dimensionally calibrated screen image or proof that every 3005 bar fits. Verify the actual saw, chain, sprocket and bar markings; no physical interchange test or hardware operation was performed.
- PDF28 .050-inch 3/8 P group: 12-inch / 44 drive links — 3005 000 4805; 14-inch / 50 links* — 3005 000 4809 or E Light 3005 000 7409; 16-inch / 55 links* — 3005 008 4813 or E Light 3005 000 7413. These Rollomatic E bars have 9-tooth noses. The asterisk again adds one link only with BOTH a 7-tooth drive sprocket AND quick chain tensioner.
- PDF17 .050-inch 3/8 P chain group including 017/018: green 63 PMC3, 63 PS3 and 63 PD3, each listed with 44 links (12-inch), 50 links (14-inch) or 55 links (16-inch); the same three types also list 51 links (14-inch) and 56 links (16-inch), each marked ** for BOTH the 7-tooth chain sprocket AND quick chain tensioner. Yellow 63 PMC has the same 44/50/55 and conditional 51/56 entries but is NOT classified low-kickback. The file column shows 5/32 inch. PDF16 chain-family prefixes are 3636 (PMC3), 3616 (PS3), 3612 (PD3), and 3613 (PMC); those prefixes are not complete order numbers.
- In the same PDF28 bar-model group, 1/4-inch/.050-inch carving entries are Duromatic C 3005 003 4203 (10-inch, 56 links) and 3005 003 4205 (12-inch, 64 links), with 8-tooth sprocket kit 1123 007 1029. Footnote1 restricts these carving bars to 13 RMC or 13 RMS chain. The bar cells are green, but this does not make the separately listed chains green.
- Unresolved cross-table scope: the PDF17 1/4-inch chain group lists later MS models and others but does NOT explicitly name 017 or 018, unlike PDF28’s carving-bar group. Do not promote 13 RMC/RMS to a fully verified 017/018 cutting combination. The chain page says no recommended green low-kickback chain is available for 1/4-inch sprockets and limits 13 RMC/13 RMS to carving bars. A bar-only listing is not complete chain approval.
- These later .050 and carving entries do not authorize former 4105/4109 Mini bars for 018 with PMN, change the 1998 restriction, or establish that a listed conversion kit is present on an individual saw.
TI dependency: TI 42/1998, p. 3 — TI42/1998 section2.4 dependency; later2011 catalog reference, not values printed in the TI.
Later manual evidence: STIHL Bar & Chain Catalog, 12th edition (2011-01), section Selection/warning context printed1–9; chain-family/selection24–27, bar context40–43 and017/018 bar/sprocket groups46–47, PDF pages 3, 4, 5, 6, 7, 16, 17, 25, 26, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · 017 / 018
017/018 Mini bars: later special-label identities are not supersessions
Five relevant special-label rows preserve their exact standard-bar numbers, including conflicting 000/008 prefixes.
- This is a later USA catalog reference (12th edition, effective January 2011), not the exact catalog cited by TI42/1998. Only the explicitly named 017 and 018 are bound here; the group also contains other models, but no blanket successor or 018 C applicability is inferred. Keep the separate 1998 PMN-only 3905/3909 restriction unchanged.
- The catalog recommends green-labeled reduced-kickback bars together with green-labeled low-kickback chains. Green does not mean kickback-free or tested with every possible powerhead/bar combination. Yellow chains carry increased kickback risk and are intended only for users with extraordinary cutting needs, experience and specialized training. Historical ANSI B175.1-2000 statements are source context, not a new current-compliance certification.
- Bar length is in inches, gauge is the drive-link/bar-groove width in inches, and pitch must match the chain and sprocket. Bar-nose tooth counts are not drive-sprocket tooth counts. The printed 3005 bar-tail template is identification context, not a dimensionally calibrated screen image or proof that every 3005 bar fits. Verify the actual saw, chain, sprocket and bar markings; no physical interchange test or hardware operation was performed.
- PDF27, printed44, says specially labeled bars are omitted from the saw/guide-bar assignment table. These five Mini-family entries are label-to-standard identities stated by that table, not newly approved 017/018 combinations or dated supersession edges.
- 3005 803 3909 (MiniBoss) — table states identical with standard guide bar 3005 008 3909.
- 3005 804 3905 (TIMBERSPORTS) — table states identical with standard guide bar 3005 008 3905.
- 3005 811 3909 (MiniBoss) — table states identical with standard guide bar 3005 008 3909.
- 3005 811 3913 (MiniBoss) — table states identical with standard guide bar 3005 008 3913.
- 3005 815 3909 (MiniBoss) — table states identical with standard guide bar 3005 000 3909.
- The 3005 804 3905 TIMBERSPORTS row points to 3005 008 3905, but the PDF28 selection table and TI42/1998 use 3005 000 3905. The 3005 815 3909 MiniBoss row points to 3005 000 3909, unlike the other two 3909 label rows and the 2011 selection row, which point to 3005 008 3909. Preserve all printed prefixes; no silent correction, equivalence between 000 and 008, or chronology is established.
- Other special-label rows on printed44 concern different bars and are outside this 017/018 Mini review. Printed45 is a blank notes page and was visually inspected. No replacement graph, raw IPL row or general model fitment is changed.
TI dependency: TI 42/1998, p. 3 — TI42/1998 section2.4 dependency; later2011 catalog reference, not values printed in the TI.
Later manual evidence: STIHL Bar & Chain Catalog, 12th edition (2011-01), section Selection/warning context printed1–9; bar-tail context42–43, special-label table44, blanknotes45 andbar selection46–47, PDF pages 3, 4, 5, 6, 7, 26, 27, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the 017? Report a correction →