Stihl 1130 · Section B · 2 of 10 · 30 parts
Cylinder
Fits 017.
Historical fitment & changes (10) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1130 020 1207 | Cylinder with piston Ø 37 mm — 30.1 cc | 1 |
| 1 | 1130 020 1200 | Cylinder with piston Ø 37 mm Fitment / change note → — 30.1 cc | 1 |
| 2 | 1130 020 1207 | Cylinder with piston Ø 37 mm — 30.1 cc | 1 |
| 2 | 1130 020 1202 | Cylinder with piston Ø 37 mm — 30.1 cc no longer available from factory | 1 |
| 3 | 1130 030 2000 | Piston Ø 37 mm Fitment / change note → — 30.1 cc | 1 |
| 4 | 1130 034 3003 | Piston ring Ø 37x1.2 mm — 30.1 cc | 2 |
| 5 | 1130 034 1500 | Piston pin 8x4x25 → replaced by 1132 034 1501 TI 6/2000 | 1 |
| 6 | 9463 650 0807 | Snap ring 8x0.7 | 2 |
| 7 | 1123 020 9400 | Decompression valve | 1 |
| 8 | 1132 030 0401 | Crankshaft | 1 |
| 9 | 9503 003 0311 | Grooved ball bearing 6002 | 2 |
| 10 | 9638 003 1581 | Oil seal 15x25x5 | 2 |
| 10 | 9639 003 1585 | Oil seal 15x25x5 | 2 |
| 11 | 9468 621 1520 | Circlip 15x1 | 1 |
| 12 | 1130 021 2505 | Engine pan Fitment / change note → | 1 |
| 13 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 Fitment / change note → | 8 |
| 14 | 1123 148 1201 | Screw M5x65 | 2 |
| 16 | 1130 141 9000 | Screen | 1 |
| 17 | 1130 145 2900 | Muffler cover | 1 |
| 18 | 9216 261 0700 | Hexagon nut M5 | 2 |
| 19 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 19 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 20 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| 40 | 1130 034 3001 | Piston ring Ø 37x1.5 mm Fitment / change note → — 30.1 cc | 1 |
| 41 | 1130 034 3000 | Piston ring Ø 37x1.5 mm Fitment / change note → → replaced by 1130 034 3001 TI 28/1996 — 30.1 cc | 1 |
| 42 | 1130 028 0200 | Collar screw Fitment / change note → | 4 |
| 43 | not sold separately | Connecting rod no longer available from factory | 1 |
| 44 | 1130 007 1000 | Set of cylindrical rollers Fitment / change note → | 1 |
| 45 | 1130 021 2500 | Engine pan Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1130 030 0450 | Set of crankshaft / engine pan Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 017
017 introduction: fixed jet, spark screen and tool-free shroud
Original 1995 equipment includes AV handles and an inertia-tripped chain brake.
- The compact lightweight entry-level saw is described for homeowners/DIY cutting around house and garden. Reliability, ease of use, ergonomics, favorable price and matched cutting attachment are source descriptions, not measured present-day performance.
- Equipment: AV handle system, electronic magneto ignition, inertia-tripped chain brake and exhaust spark-arresting screen. The muffler screen is specified in ALL MARKETS; the exploded figure shows the screen between muffler body and cover, not an optional US-only item.
- The carburetor has a FIXED JET and NO HIGH-SPEED SCREW. The central shroud can be removed WITHOUT TOOLS. The figures give component layout, not an undisclosed part number, carburetor maker/type or conversion procedure.
- The TI attributes meeting US CARB emissions standards to the fixed-jet carburetor and engine tuning. This is a historical source claim, not verification of current emissions compliance or permission to modify emissions equipment.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 1 · TI 23/1995, p. 2 — Sections 1–3, overview and figures 143TI001–003.
No additional parts-table entry added.
Service note · 017
017 engine, starter and dimensions: original 30.1 cm³ specification
37-mm bore, 28-mm stroke and 3.8-kg dry powerhead; attachment weight excluded.
- Single-cylinder two-stroke engine with special impregnated cylinder bore; displacement 30.1 cm³ (1.84 cu.in), bore 37 mm (1.46 in), stroke 28 mm (1.10 in), compression ratio 9.5:1 and engine power 1.1 kW (1.5 bhp). No bore coating composition is named.
- Maximum torque 1.5 Nm (1.1 lb.ft) at 6500 rpm; mean idle 3200 rpm. These are not maximum unloaded speed or clutch engagement speed.
- One-piece drop-forged crankshaft; TWO deep-groove ball main bearings; crankpin diameter 11.35 mm (0.45 in); cageless cylindrical-roller big end; connecting rod length 51 mm (2 in); piston pin diameter 8 mm (0.3 in); needle-cage small end. No rod-length measurement datum is supplied.
- Lining-free centrifugal clutch diameter 67 mm (2.64 in); engagement approximately 4100 rpm. Pawl starter with automatic rope rewind; rope diameter 3.0 mm (0.12 in), length 800 mm (31.5 in). Later 017 C sheet also lists 3x800-mm rope, but does not make every listed starter/ignition revision original 1995 equipment.
- Dry powerhead WITHOUT BAR AND CHAIN weighs 3.8 kg (8.4 lb). Dimensions WITHOUT BAR AND CHAIN: length 380 mm (14.96 in), width 230 mm (9.0 in), height 250 mm (9.84 in). These are not fueled operating weight or overall cutting-attachment dimensions.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 3 · TI 23/1995, p. 7 · TI 23/1995, p. 8 — Sections 4.1, 4.6 and 4.7.
No additional parts-table entry added.
Service note · 017
017 ignition: air gap, timing and suppressed plugs
0.15–0.30-mm air gap and timing referenced specifically to 8000 rpm.
- Breakerless electronic magneto ignition; module air gap 0.15–0.30 mm (0.006–0.012 in). Ignition timing 1.0–1.6 mm (0.04–0.063 in) BEFORE TOP DEAD CENTER at 8000 rpm; this is piston travel, not crankshaft degrees or a universal static setting.
- Suppressed spark plugs CHAMPION RCJ 6Y or BOSCH WSR 6 F; electrode gap 0.5 mm (0.020 in), thread M14x1.25, thread length 9.5 mm (0.37 in), printed heat range 200. Do not reinterpret 200 as a universal modern cross-brand heat-range equivalence.
- Later 017 B sheet lists Bosch WSR 6 F and NGK BPMR7A. The later NGK listing does not erase the TI Champion option or establish an undocumented 1995 supersession. No plug ordering number is printed in this TI section.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 3 — Section 4.3 ignition system.
No additional parts-table entry added.
Service note · 017
017 fastener torques and DG-thread reuse
The same DG 5x24 thread has different crankcase and fan-housing torques.
- Spline screws: IS-DG 4x20 ignition module/cylinder 5.0 Nm (3.7 lbf.ft); IS-DG 5x24 crankcase 9.5 Nm (7.0); IS-DG 5x24 fan housing/crankcase 4.5 Nm (3.3); IS-DG 5x26 crankcase/cylinder/bar mounting 9.5 Nm (7.0). Same thread size does NOT imply the same component torque.
- M8 collar screw into crankcase 16.0 Nm (11.8 lbf.ft), secured with adhesive 0786 111 1101 (LOCTITE 243), per remark 1. M12x1L clutch collar nut 50.0 Nm (37.0): retain the LEFT-HAND thread suffix L.
- M5 carburetor nut 3.5 Nm (2.6 lbf.ft); M5 muffler/cylinder nut 7.0 Nm (5.2); M8x1 flywheel collar nut 27.5 Nm (20.2); M14x1.25 spark plug 25.0 Nm (18.5). These figures are distinct from valve or bar-fastener values.
- IS-P 4x12 hand guard/fan housing screw 1.7 Nm (1.25 lbf.ft). ONLY THIS ROW carries remark 2: torque may be reduced by approximately 1 Nm (0.7 lbf.ft) when refitting in an existing thread. Do not apply that reduction to every DG screw or all listed fasteners.
- DG screws form a permanent thread in polymer on first installation. To reuse: turn COUNTERCLOCKWISE until the screw drops slightly into the existing thread, then clockwise to specified torque. A torque wrench is essential; cutting a new parallel thread is not the prescribed procedure.
- The TI notes adhesive-secured screws are easier to release after heating adhesive with a hot-air blower/hair dryer; DO NOT OVERHEAT POLYMER COMPONENTS. No heating temperature/time is specified. This is retained historical guidance, not a performed repair.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 7 — Section 4.5, every torque row, DG refitting procedure and remarks.
Part numbers (1)
- 0786 111 1101 — LOCTITE 243 adhesiveremark 1; M8 crankcase collar screw · 017; Section 4.5, every torque row, DG refitting procedure and remarks
Service note · 017
017 leak-test and oil-seal service tools
Keep exhaust sealing, pressure testing, vacuum testing and seal tools distinct.
- Sealing plate 0000 855 8106 seals the exhaust port for leakage testing; indented flange 1123 855 4200 and sleeve 1123 851 8300 remain associated tooling rows. Test flange 1118 850 4200 is separately listed for leakage testing. No unprinted quantity or complete-kit inclusion is inferred.
- Carburetor/crankcase tester 1106 850 2905 checks leakage; vacuum pump 0000 850 3501 checks crankcase leakage, with indented nipple 0000 855 9200 and fuel line 1110 141 8600 rows. These do not replace the distinct pressure/vacuum magnitudes specified in section 4.
- Oil-seal puller 0000 890 4400 and jaws 0000 893 3706 remove seals; press sleeve 1123 893 2400 installs seals; guide sleeve 1123 894 7700 PROTECTS THE STARTER-SIDE seal. No hidden pressure-decay criteria or tool assembly procedure is supplied.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 9 — Section 5.2, leakage-test and oil-seal tooling rows.
Part numbers (12)
- 0000 855 8106 — Sealing plateseal exhaust port for leakage test · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1123 855 4200 — Flangeindented sealing-tool row · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1123 851 8300 — Sleeveindented sealing-tool row · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1118 850 4200 — Test flangeleakage test · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1106 850 2905 — Carburetor and crankcase testerpressure leakage testing · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 0000 850 3501 — Vacuum pumpcrankcase leakage testing · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 0000 855 9200 — Nippleindented vacuum-pump row · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1110 141 8600 — Fuel lineindented vacuum-pump row · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 0000 890 4400 — Oil-seal pullerremoval · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 0000 893 3706 — Jawsindented puller row · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1123 893 2400 — Press sleeveinstall oil seals · 017; Section 5.2, leakage-test and oil-seal tooling rows
- 1123 894 7700 — Guide sleeveprotect starter-side oil seal · 017; Section 5.2, leakage-test and oil-seal tooling rows
Service note · 017
017 piston, ignition, clutch and holding tools
Exact tool applications, including hookless snap rings and 13/19-mm sockets.
- Locking strip 0000 893 5903 blocks crankshaft; clip 1120 893 9100 holds big-end bearing; drift 1114 893 4700 installs piston pin; installing tool 8 5910 890 2208 fits HOOKLESS piston snap rings. The printed 8 is a tool designation, not eight tools.
- Assembly tube 1117 890 0900 fits clutch spring; M8 stud puller 5910 893 0501 unscrews bar-mounting studs. Setting gauge 1111 890 6400 sets ignition module/flywheel air gap. Assembly tool 1116 893 4800 rewinds the rewind spring; hook 5910 893 8800 removes the FUEL pickup body, not the oil pickup.
- Assembly stand 5910 890 3100 holds the saw; clamping bar 5910 890 2000 mounts it to the stand. Crimping tool 5910 890 8210 attaches electrical-wire connectors; puller 1116 893 0800 removes flywheel.
- Socket 5910 893 5608 is 13 mm for the FLYWHEEL NUT; socket 5910 893 5612 is 19 mm for the CLUTCH. No complete interchange or machining specification for these tools is inferred.
- Historical TI guidance for model 017 as described in TI23/1995; shared series 1130 or tooling does not extend these specifications to 018, MS170, MS180 or later variants. No serial cutoff, present stock guarantee or physical interchange verification is implied. No hardware operation was performed.
Source: TI 23/1995, p. 9 — Section 5.2, assembly/holding, electrical, starter and socket rows.
Part numbers (15)
- 0000 893 5903 — Piston locking stripblock crankshaft · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1120 893 9100 — Cliphold big-end bearing · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1114 893 4700 — Assembly driftinstall piston pin · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 2208 — Installing tool 8fit hookless piston snap rings · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1117 890 0900 — Assembly tubefit clutch spring · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 0501 — M8 stud pullerunscrew bar-mounting studs · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1111 890 6400 — Setting gaugeignition module/flywheel air gap · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1116 893 4800 — Assembly toolrewind starter spring · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 8800 — Assembly hookremove fuel pickup body · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 3100 — Assembly standhold saw for repairs · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 2000 — Clamping barmount saw to stand · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 890 8210 — Crimping toolattach electrical connectors · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 1116 893 0800 — Flywheel pullerremove flywheel · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 5608 — 13-mm socketflywheel nut · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
- 5910 893 5612 — 19-mm socketclutch · 017; Section 5.2, assembly/holding, electrical, starter and socket rows
Historical fitment · 017
017: matched piston/ring revisions, not loose-ring interchange
From X 33 249 875, ring 1130 034 3001 uses an upper-edge peg; complete matched piston/ring assemblies interchange.
X 33 249 875 — Section1 piston/ring revision; do not independently assign this cutoff to the section 2 flywheel change.
- From X 33 249 875, the ring closes on a peg at the UPPER EDGE of the piston groove rather than its center. Drawing 143TI008 labels 1 original and 2 new; these are comparison versions, not the summary-table positions. Ring 1130 034 3000 becomes 1130 034 3001 in production.
- Original and new pistons are completely interchangeable ONLY as matched assemblies (piston WITH ring). The original ring CANNOT be combined with the new piston, and the new ring CANNOT be combined with the original piston. An unchanged piston part number is not proof that any loose ring fits its installed revision.
- Summary item 1 cylinder with piston 1130 020 1200 includes item 2 piston 1130 030 2000, which includes item 3 ring. Cylinder assembly and piston numbers are UNCHANGED across the revision; only their MODIFIED versions are available from the factory under remark 1. Original ring 1130 034 3000 remains available as a spare for older machines under remark 2. These are historical 1996 supply statements, not current availability.
- The source attributes improved gas-tight sealing, compression, performance and starting to the new ring. These are reported design effects, not measured results for an owner machine.
- Later SCS 01-2012 sheet B retains both historical ring numbers at positions 40/41, while also listing other cylinders and a 37x1.2 mm ring 1130 034 3003 at position 4 (quantity 2). Those later entries do not override this matched-revision restriction or establish a supersession chain to that other ring.
- Applies to named model 017 only, not 018, MS 170 or other series 1130 machines by family association. No hardware operation was performed.
Source: TI 28/1996, p. 1 · TI 28/1996, p. 2 — Complete sections1–2, original comparison drawing, all summary rows and remarks.
Part numbers (4)
- 1130 020 1200 — Cylinder with pistonUnchanged number; modified assembly only · 017; matched piston/ring revision
- 1130 030 2000 — Piston with ringUnchanged number; matched ring required · 017; matched piston/ring revision
- 1130 034 3000 — Piston ring for center-groove pegOriginal; retained older-machine spare · 017; matched piston/ring revision
- 1130 034 3001 — Piston ring for upper-edge pegNew; requires matching piston · 017; matched piston/ring revision
Conditional replacement · 017 / 017 C
017 / 017 C: housing bushings require the matching screws
Revised housings use four DG screws; original housings must retain collar screws.
in progress — Housing introduction only; no serial cutoff. Original housings require collar screws; four-year inclusion is historical.
- FOUR BUSHINGS will be pressed into the engine housing to optimize the housing/cylinder assembly. Housing 1130 020 3000 becomes 1130 020 3001 for 017; housing 1130 020 3010 becomes 1130 020 3011 for 017 C. These are separate model-specific replacements, not interchangeable housing variants.
- FOUR DG screws 9075 478 4159 replace collar screws 1130 028 0200 in the modified assembly. The summary specifies IS-DG 5x24 (4x). Service restriction: COLLAR SCREWS MUST STILL BE USED IN ORIGINAL HOUSINGS. This is not permission to put DG screws into an old housing or to press in unspecified retrofit bushings; no bushing part number, drilling procedure or torque is supplied.
- Each new housing includes four DG screws FOR THE NEXT FOUR YEARS, a historical temporary supply promise, not permanent present-day kit contents. Housing introduction is IN PROGRESS, with NO SERIAL CUTOFF. Original housings are supplied ONLY WHILE STOCKS LAST; the original collar screw REMAINS AVAILABLE AS A SPARE. The WT325A serial in section 3 does not govern the housings.
- Exact 017 engine-housing IPL retains both 3001 and 3011 plus later 3002. The 017 cylinder sheet retains collar screw 1130 028 0200 with quantity 4 and DG screw 9075 478 4159 with quantity 8 and description IS-D5x24. Its assembly-wide quantity and wording do not replace this TI’s four-screw inclusion and IS-DG label. Later 3002 is not silently substituted for the TI housing; its later bulletin remains in the serial queue.
- Historical TI 12/1998, model 017, series 1130; 017 C is expressly distinguished in the housing section. Shared parts do not extend these instructions to 018, MS170 or MS180. Factory supply statements are historical, not current availability. Source-stated repair permission is not physical-fit verification. No hardware operation was performed.
Source: TI 12/1998, p. 1 — Section 1 complete prose, service restriction, four summary rows, temporary screw inclusion and both supply remarks.
Part numbers (6)
- 1130 020 3000 — Original 017 engine housingStock-limited original · 017 only
- 1130 020 3001 — Modified 017 engine housingFour bushings; temporary four-DG-screw inclusion · 017 only
- 1130 020 3010 — Original 017 C engine housingStock-limited original · 017 C only
- 1130 020 3011 — Modified 017 C engine housingFour bushings; temporary four-DG-screw inclusion · 017 C only
- 9075 478 4159 — Screw IS-DG 5x24Four for modified assembly · 017 / 017 C; original versus modified housing restriction applies
- 1130 028 0200 — Original collar screwRequired in original housings; remains spare · 017 / 017 C; original versus modified housing restriction applies
Conditional replacement · 017
017: built-up crankshaft requires its matching engine pan
Crankshaft 1132 030 0400 requires engine pan 1130 021 2505; TI09/1999 retains conflicting original-machine and previous/new wording.
- The announcement replaces the original one-piece crankshaft with a built-up crankshaft. Summary item6 lists crankshaft/engine-pan set 1130 030 0450 in the New column, including item7 crankshaft 1132 030 0400 and item8 engine pan 1130 021 2505. This is a paired assembly, not an unconditional one-for-one crankshaft substitution.
- The service note says the new crankshaft may be installed only with engine pan 1130 021 2505. Remark4 likewise allows item7 in older machines only in conjunction with item8. Do not install the new crankshaft with original pan 1130 021 2500 on the authority of this TI.
- Unresolved source conflict: the very next service-note sentence says the new engine pan must not be fitted to original-type machines, while remark4 permits the crankshaft in older machines together with that pan. Both statements are printed in the original scan. Do not silently change the prohibition to a standalone-pan rule, infer that older and original-type machines are equivalent, or treat this note as a complete retrofit authorization.
- Unresolved chronology wording: the prose calls set 1130 030 0450 the previous version and says it will remain available for about 6 years, yet the summary puts that same set and its two components in the New column. The number and stated contents agree; the previous/new classification does not. About 6 years is an approximate historical supply statement, not an exact end date or guarantee of current supply.
- Summary item9 is a connecting rod with the new-number placeholder -*- and remark5: not available as a separate item. No order number is supplied. This does not cancel the separate original connecting-rod spare statement in item3.
- The retained SCS01-2012 USA exact 017 cylinder sheet lists set 1130 030 0450 in an unnumbered row and pan 1130 021 2505 at position12, but crankshaft 1132 030 0401 at position8 rather than this TI’s 1132 030 0400. Preserve the dated difference; TI09 supplies no 0400-to-0401 supersession, date or interchange rule. Catalog positions are not TI item numbers.
- No physical interchange or hardware work was performed. The explicit pair requirement is retained, but the conflicting original-machine wording remains unresolved.
- TI09/1999 names Model 017, series 1130. The mention of changes to model 018 explains the context, not applicability to 018, MS 170 or MS 180. Introduction is in progress, with no serial or exact production-date cutoff. Factory availability is a historical statement, not present-day stock. TI46/1998 is backward bibliography, not an additional prerequisite.
Source: TI 9/1999, p. 1 — Complete page: crankshaft announcement, service note, summary items1–9 and remarks1–5.
Part numbers (3)
- 1130 030 0450 — Crankshaft/engine-pan set; item6Includes items7 and8; prose previous versus table New conflict retained · 017; TI09/1999 restrictions apply
- 1132 030 0400 — Built-up crankshaft; item7Requires item8 engine pan; remark4 · 017; TI09/1999 restrictions apply
- 1130 021 2505 — Matching engine pan; item8Required with item7; original-type-machine prohibition retained · 017; TI09/1999 restrictions apply
Historical fitment · 017
017: original crankshaft and separate spare availability
Original crankshaft 1130 031 0500 is no longer available from the factory; the original pan, rod, needle sleeve and roller set have distinct retained-spare remarks.
- Summary item1 identifies original crankshaft 1130 031 0500, with no direct new number in its row. Remark1 says it is no longer available from the factory. The paired crankshaft/engine-pan change is separately listed in items6–8 and carries the service-note conflict, not a blanket replacement approval.
- Original engine pan 1130 021 2500 (item2), connecting rod 1130 030 1200 (item3) and set of cylindrical rollers 1130 007 1000 (item5) each carry remark2: they remain available as spares for older machines. Their New-column dashes do not mean universal discontinuation or fitment to the new built-up crankshaft.
- Item3 explicitly includes item4, needle sleeve 9513 003 1920, specified 8x12x10. Item4 carries remark3: the original version remains available as a spare. Preserve the inclusion relationship and its distinct remark; do not move the item9 non-separate connecting-rod restriction onto original item3.
- The later retained SCS01-2012 USA exact 017 cylinder sheet still lists roller set 1130 007 1000 at position44 and original pan 1130 021 2500 at position45. Its position43 connecting rod has no order number; original crankshaft 1130 031 0500, rod 1130 030 1200 and sleeve 9513 003 1920 are absent as numbered rows. Later absence does not erase the historical TI numbers or establish a later discontinuation date.
- TI09/1999 names Model 017, series 1130. The mention of changes to model 018 explains the context, not applicability to 018, MS 170 or MS 180. Introduction is in progress, with no serial or exact production-date cutoff. Factory availability is a historical statement, not present-day stock. TI46/1998 is backward bibliography, not an additional prerequisite.
Source: TI 9/1999, p. 1 — Complete page: crankshaft announcement, service note, summary items1–9 and remarks1–5.
Part numbers (5)
- 1130 031 0500 — Original one-piece crankshaft; item1No longer available from factory; remark1 · 017; TI09/1999 restrictions apply
- 1130 021 2500 — Original engine pan; item2Spare for older machines; remark2 · 017; TI09/1999 restrictions apply
- 1130 030 1200 — Original connecting rod; item3Spare for older machines; includes item4; remark2 · 017; TI09/1999 restrictions apply
- 9513 003 1920 — Needle sleeve 8x12x10; item4Included with item3; remains available as spare; remark3 · 017; TI09/1999 restrictions apply
- 1130 007 1000 — Set of cylindrical rollers; item5Spare for older machines; remark2 · 017; TI09/1999 restrictions apply
Wrong number or missing part for the 017? Report a correction →