Stihl 1130 · Section J · 9 of 10 · 38 parts
Carburetor WT-325A (05.2000)
Fits 017.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (38)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1115 121 5401 | Valve jet | 1 |
| 2 | 4117 122 9402 | Plug | 1 |
| 3 | 1130 121 5400 | Fixed jet 0.54 | 1 |
| 4 | 4133 120 8600 | Non-return valve | 1 |
| 5 | 4116 121 5100 | Inlet needle | 1 |
| 6 | 1130 122 3000 | Spring Fitment / change note → | 1 |
| 7 | 1113 121 5000 | Inlet control lever | 1 |
| 8 | 1113 121 9200 | Spindle | 1 |
| 9 | 1114 122 7400 | Round head screw | 1 |
| 10 | 1113 129 0900 | Gasket Fitment / change note → | 1 |
| 11 | 1113 121 4705 | Metering diaphragm Fitment / change note → | 1 |
| 12 | 1113 121 0800 | End cover | 1 |
| 13 | 1106 122 7400 | Round head screw | 4 |
| 14 | 1114 121 7800 | Strainer | 1 |
| 15 | 1121 121 4801 | Pump diaphragm | 1 |
| 16 | 1120 129 0905 | Gasket | 1 |
| 17 | 1123 121 0802 | End cover | 1 |
| 18 | 1114 122 7100 | Screw | 1 |
| 19 | 4117 122 3006 | Spring | 1 |
| 20 | 4117 122 6200 | Idle speed adjustment screw | 1 |
| 21 | 1130 122 3200 | Torsion spring | 1 |
| 22 | 1130 120 7100 | Throttle shaft with lever | 1 |
| 23 | 1130 121 3300 | Throttle shutter | 1 |
| 24 | 1115 122 7400 | Round head screw | 1 |
| 25 | 1117 122 9000 | E-clip | 1 |
| 26 | 1130 122 6800 | Low speed adjustment screw Fitment / change note → | 1 |
| 27 | 1115 122 3002 | Spring | 1 |
| 28 | 1111 121 8605 | Washer | 1 |
| 29 | 4124 122 3600 | Sealing ring | 1 |
| 30 | 1123 122 3201 | Torsion spring | 1 |
| 31 | 1123 120 7201 | Choke shaft with lever | 1 |
| 32 | 1110 122 7400 | Round head screw | 1 |
| 33 | 1123 122 9000 | E-clip | 1 |
| 34 | 1130 121 2900 | Choke shutter | 1 |
| 35 | 1129 121 5600 | Fixed jet 0.50 Fitment / change note → option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1130 120 0600 | Carburetor WT-325A Fitment / change note → → replaced by 1130 120 0601 TI 5/2000 | 1 |
| — | 1123 007 1061 | Set of carburetor parts | 1 |
| — | 1130 007 1001 | Repair kit for carburetor Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 017
017: WT325 repair kit upgrades to WT325A standard
Four-component kit targets acceleration; X 37 672 609 describes WT325A factory installation, not the housing or vent changes.
X 37 672 609 — WT325A factory installation from this machine number. Repair kit separately in progress; not a housing/oil-tank cutoff.
- Repair kit 1130 007 1001 is AVAILABLE FOR WT325 and designed to HELP IMPROVE ACCELERATION. Installation of the parts contained in the kit upgrades WT325 to the SAME STANDARD AS WT325A. This is a source-stated upgrade, not measured performance, a universal carburetor substitution or an instruction to replace an already correct carburetor.
- WT325A is installed FROM MACHINE NUMBER X 37 672 609. The summary separately says modification introduction IN PROGRESS. Preserve the printed X marker and distinguish the WT325A factory cutoff from repair-kit availability; no numeric-only universal model cutoff or automatic end date for repair eligibility is established.
- Kit includes summary items 2–5: low speed adjusting screw 1130 122 6800, spring 1130 122 3000, metering diaphragm 1113 121 4705 and gasket 1113 129 0900. ALL FOUR components are ALREADY IN INVENTORY (remark 1). No additional kit contents, mixture setting, metering-lever dimension or tuning procedure is supplied.
- Exact 017 WT-325A IPL retains kit 1130 007 1001 and all four listed components. The kit spring 1130 122 3000 is distinct from the separately cataloged spring beside the low-speed screw; do not substitute a nearby row. Other 017 carburetor sheets are C1Q variants, not recipients of this WT325 kit by shared model name. Footer last TI 28.96, copyright 1998 and documentation 6274 are bibliographic context, not a delegated repair dependency.
- Historical TI 12/1998, model 017, series 1130; 017 C is expressly distinguished in the housing section. Shared parts do not extend these instructions to 018, MS170 or MS180. Factory supply statements are historical, not current availability. Source-stated repair permission is not physical-fit verification. No hardware operation was performed.
Source: TI 12/1998, p. 2 — Section 3 complete prose, WT325A cutoff, five summary rows, in-progress introduction, inventory remark and footer.
Part numbers (5)
- 1130 007 1001 — Repair kit for WT325 carburetorIncludes items 2–5; WT325 to WT325A standard · 017; exact variant/component restrictions in this note
- 1130 122 6800 — Low speed adjusting screwKit item 2; already in inventory · 017; exact variant/component restrictions in this note
- 1130 122 3000 — SpringKit item 3; already in inventory · 017; exact variant/component restrictions in this note
- 1113 121 4705 — Metering diaphragmKit item 4; already in inventory · 017; exact variant/component restrictions in this note
- 1113 129 0900 — GasketKit item 5; already in inventory · 017; exact variant/component restrictions in this note
Historical fitment · 017
017: optional 0.50 mm jet for WT-325 A
Optional high-altitude jets selected by stamped carburetor type; exact table associations and restrictions retained.
- Use ONLY the type designation stamped on the carburetor body, not the saw model or carburetor part number alone. Each row below retains its exact printed suffix; later suffixes and MS successor models are not admitted by a shared number or sheet.
- These are OPTIONAL smaller-bore high-altitude jets, not standard jets or unconditional replacements. For adjustable carburetors WITH a semi-fixed jet, TI29/1998 permits leaner adjustment down to H = 0 if necessary; the smaller-bore option is for very high altitude when that range is insufficient. This is not a universal H setting for other designs and no numeric altitude threshold is supplied.
- Do NOT use the smaller-bore high-altitude jets at lower altitudes: an overly lean mixture can cause engine damage. Replacement is for trained personnel; press-fit positioning depends on the separate Carburetors handbook. No complete installation procedure, regulatory approval or physical interchange test is claimed. No hardware operation was performed.
- WT 325 A: carburetor 1130 120 0600; optional fixed jet 1129 121 5600, bore 0.50 mm; source model 017. No USA-only asterisk is printed on this row.
- The exact retained WT-325A sheet also lists 0.54 mm jet 1130 121 5400. The TI optional 0.50 mm choice does not overwrite or universally replace that standard row.
Source: TI 29/1998, p. 1 · TI 29/1998, p. 2 — Page 1 complete guidance and page 2 WT 325 A table rows.
Part numbers (2)
- 1130 120 0600 — Carburetor WT 325 ASource type association · 017; stamped WT 325 A only
- 1129 121 5600 — High-altitude fixed jet, 0.50 mmOptional, not standard · WT 325 A; 017; high-altitude conditions only
Wrong number or missing part for the 017? Report a correction →