← 019 T · MS 190 T · MS 191 T

Stihl 1132 · Section A · 1 of 9 · 25 parts

Cylinder with piston, Ignition system

Fits 019 T.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111111111213141516171819220212223345677889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (25)

PosPart numberDescriptionQty
1 1132 020 1200 Cylinder with piston Ø 40 mm — 35.2 cc 1
2 1132 030 2000 Piston Ø 40 mm — 35.2 cc 1
3 1132 034 3000 Piston ring Ø 40x1.5 mm — 35.2 cc 1
4 1130 034 1500 Piston pin 8x4x25 → replaced by 1132 034 1501 TI 6/2000 1
5 9463 650 0805 Snap ring 8x0.7 2
6 1132 030 0401 Crankshaft Fitment / change note → 1
7 9503 003 0311 Grooved ball bearing 6002 2
8 9638 003 1581 Oil seal 15x25x5 2
8 9639 003 1585 Oil seal 15x25x5 2
9 9468 621 1520 Circlip 15x1 1
10 1132 021 2505 Engine pan 1
11 9075 478 4159 Pan head self-tapping screw IS-D5x24 10
12 1132 140 0600 Muffler 1
13 1132 145 0600 Cover plate 1
14 1132 141 9000 Screen 1
15 9099 021 0810 Self-tapping screw 4.2x9.5 1
16 1132 400 1300 Ignition module Fitment / change note → 1
17 9075 478 3022 Pan head self-tapping screw IS-D4x20 2
18 1110 400 7005 Spark plug Bosch WSR 6 F 1
18 0000 400 7000 Spark plug NGK BPMR7A 1
19 1132 440 3000 Wiring harness 1
20 1130 400 1200 Flywheel Fitment / change note → 1
21 1132 442 9001 Grommet 1
22 0000 955 0802 Collar nut M8x1 1
23 0783 830 2000 Tube of sealant Dirko HT red 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 019 T

019 T: series 1132 replacement ignition assignment

1132 400 1300 and the listed flywheel pairing for series 1132; ignition lead not replaceable.

  • Listed configuration: 1132 400 1300 with flywheel 1130 400 1200.
  • The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.

Part numbers (2)
  • 1132 400 1300 — Replacement ignition moduleAssigned replacement · 019 T, series 1132, only with the listed flywheel branch
  • 1130 400 1200 — Listed configuration flywheelRequired pairing · 019 T, series 1132; listed configuration only

Service note · 019 T

019 T: engine, clutch and starter specifications

35.2 cm³, 40 mm bore, 28 mm stroke; 1.2 kW at 7,500 rpm; 12,000 rpm maximum WITH bar and chain.

  • Section 2.1: displacement 35.2 cm³ (2.15 cu.in); bore 40 mm (1.57 in); stroke 28 mm (1.10 in); compression ratio 10.5:1.
  • Engine power 1.2 kW (1.6 bhp) at 7,500 rpm; maximum torque 1.8 Nm (1.3 lb.ft) at 5,000 rpm. Maximum engine speed WITH BAR AND CHAIN is 12,000 rpm; mean idle speed is 2,800 rpm. These distinct conditions must not be collapsed into a no-load test setting.
  • Durable built-up crankshaft; TWO deep-groove ball main bearings; needle big-end bearing; connecting rod length 51 mm (2 in); piston pin diameter 8 mm (0.3 in); needle small-end bearing. These dimensions do not identify replacement part numbers.
  • Centrifugal clutch WITHOUT LININGS, 67 mm (2.64 in) diameter; engagement at APPROXIMATELY 3,700 rpm. Pawl-engagement rewind starter with automatic starter-rope rewind; rope 3.0 mm (0.12 in) diameter and 800 mm (31.5 in) long. Optional ElastoStart is listed separately on page 4.
  • Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 3 — engine, clutch and starter specifications.

No additional parts-table entry added.

Service note · 019 T

019 T: ignition timing, spark plugs and gaps

0.2 mm air gap; 1.6–2.3 mm BTDC; CHAMPION RCJ 6Y or NGK BPMR 7 A, 0.5 mm electrode gap.

  • Section 2.3: air gap 0.2 mm (0.008 in); ignition timing 1.6–2.3 mm (0.063–0.091 in) B.T.D.C. This is a linear piston-position specification, not crankshaft degrees or an instruction to alter a module.
  • SUPPRESSED spark plug: CHAMPION RCJ 6Y OR NGK BPMR 7 A. Electrode gap 0.5 mm (0.02 in); spark-plug thread M14x1.25; thread length 9.5 mm (0.37 in). No plug torque is printed here.
  • The later retained 2012 019 T A-sheet instead lists Bosch WSR 6 F and NGK BPMR7A. Both source-era lists remain unchanged; the catalog’s Bosch entry is not inserted into this 1996 TI, and no Champion ordering number or universal plug equivalence is manufactured.
  • Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 4 — ignition timing, spark plugs and gaps.

No additional parts-table entry added.

Service note · 019 T

019 T: engine and carburetor test data; torque-source gap

Engine pressure/vacuum each printed 0.6 bar (8.7 psi); carburetor pressure 0.4 bar (5.8 psi).

  • Section 5.2 ENGINE: pressure test 0.6 bar (8.7 psi); VACUUM test 0.6 bar (8.7 psi). The scan prints the same unsigned magnitude for both. Preserve the vacuum label; this is not a second positive-pressure test or an absolute-pressure specification.
  • Section 5.2 CARBURETOR: pressure test 0.4 bar (5.8 psi). Do not substitute the engine value. No test duration, acceptable leakage/drop, sealing fixture, crankshaft position, test sequence or instrument reference is printed on this page; these three values alone are not a complete test procedure.
  • Section 5.3 gives NO TIGHTENING TORQUES and refers to the STIHL 019 T service manual. An exact applicable manual was not identified in the bounded local document/PDF metadata, exact 019 T product links or resource/owner filename inventory. This is a documented local source gap, not proof no manual exists. No MS190T/MS191T torque table or generic fastener torque is substituted.
  • Historical TI40/1996, exact 019 T only. Later 2012 IPL sheets are navigation anchors, not proof of original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.

Source: TI 40/1996, p. 6 — engine and carburetor test data; torque-source gap.

No additional parts-table entry added.

Conditional replacement · 019 T

019 T: crankshaft with stronger needle-bearing cages

Improved crankshaft; introduction in progress, without a serial cutoff.

  • Section3 replaces1132 030 0400 with1132 030 0401. Needle sleeves with a STRONGER CAGE are installed in the new crankshaft to help increase bearing life. No separate sleeve number or stand-alone bearing conversion is supplied.
  • Introduction IN PROGRESS; previous crankshaft supplied only while existing stocks last. The fan-housing/ElastoStart cutoff does not apply to this section. Later019 T sheet A/doc85 lists0401; association alone proves no universal interchange.
  • Historical TI43/1999 english/USA evidence for 019 T, series1132 only. No extension to 019, 020 T, MS190 T or MS191 T from shared parts/series. Factory-availability remarks describe the historical issue, not current stock. No universal retrofit, numerical service setting or physical interchange verification is inferred.

Source: TI 43/1999, p. 3 — crankshaft with stronger needle-bearing cages.

Part numbers (2)
  • 1132 030 0400 — CrankshaftPrevious; stocks last · 019 T; TI43 section crankshaft
  • 1132 030 0401 — Crankshaft with stronger needle-sleeve cageNew · 019 T; TI43 section crankshaft

Wrong number or missing part for the 019 T? Report a correction →